• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2013년도 추계 학술논문 발표대회
• /
• pp.188-189
• /
• 2013

The purpose of this research is to comprehend experimentally the characteristic of human dynamic load and provide the result as basic data to suggest a valid impact-resistance evaluation method. Human motions exerting dynamic load are classified to 3 types. Selecting 3 ranks of motion strength, 3 ranks of load plane stiffness (A:20kN/cm, B:4.7kN/cm, C:2.2kN/cm), and 30 male grownup inspectors in their twenties, load was measured when they applied force on load plane. Result of this research is as follows: (1) Human dynamic load has different nature from object collision in the highest load ratio depending on the load plane stiffness and action time (2) The highest load ratio for each motion was 10.06 for kicking, 4.44 for hitting with shoulder, and 5.58 for fist blow.

• 한국재난정보학회 논문집
• /
• 제13권1호
• /
• pp.73-80
• /
• 2017

이 논문에서는 프리캐스트 바닥판 위를 이동하는 차량하중에 의한 바닥판 접합거동 특성을 분석하였다. 하중 재하를 위하여 프레임을 제작하였고 각 측정 장치를 활용하여 거동을 파악하였다. 바닥판의 정적응답을 검토하여 이론값과 비교하였고 그 특성은 매우 합리적임을 알 수 있었다. 또한, 동적영향 평가를 위하여 가속도, 속도 및 변위를 측정하여 시험에서 이동하중의 특성을 분석하였다. 이동하중에 의한 동적응답을 위하여 바닥판 진동수를 측정한 결과 하중 범위 변화에 따라 진동 특성도 민감하게 반응하는 것으로 나타났다. 결과적으로 연결부의 동적 응답은 연결방법에 따라 특성이 다르므로 설계에 주의를 기울여야 할 것으로 판단된다.

• 한국지반공학회논문집
• /
• 제38권11호
• /
• pp.97-106
• /
• 2022

국내 매입말뚝 시공방법은 선굴착 후 최종단계의 항타 관입량으로 관리하는 것이 일반적이다. 관입량은 오래전부터 수기 측정방식에 의해 이루어지고 있으며, 작업자의 안전문제와 측정값의 신뢰도 부족 등에도 작업성의 한계와 비용 문제로 자동화 기술이 적용되지 않고 있다. 본 연구에서는 비접촉식 말뚝 관입량 측정 장치를 개발하고 기존 장치와 비교계측을 통해 현장 성능을 검증하였다. 또한 관입량 측정장치를 활용하여 현장 품질관리 방법에 대해 분석하였다. 실제 현장 실험을 통해 개발 장치를 활용한 관입량 측정과 수정 Hiley공식 및 동적감쇠계수 산정을 통해 보다 신뢰도 높은 지지력 추정이 가능한 것을 확인하였다. 연구결과에 따라 각 현장마다 수행된 동재하시험으로 부터 현장 보정 절차가 이루어지면 보다 신뢰성 높은 지지력 추정이 가능하며, 실제 현장에서는 동재하시험이 수행되지 않은 말뚝에 대해서도 지지력 관점의 말뚝 시공관리에 활용할 수 있을 것으로 판단된다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 춘계학술대회 논문집
• /
• pp.675-679
• /
• 2007

The control method of programmable dynamometer for overall test of machine is to load reference torque which is computed from torque transducer into motor under test. But the torque information detected from torque transducer have a lot of noise when the load torque of moter is a small quantity or changing. Thus, torque transducer must have a low pass filter to detect a definite torque information. But The torque delay generated by filter with torque transducer occur a torque trouble for moter torque of programmable dynamometer. Therefore, this kind of system could not perform dynamic and nonlinear load. In this paper, the control method using the load torque observer without a measure for torque transducer is proposed. The proposed system improved the problem of the torque measuring delay with torque transducer, and the load torque is estimated by the minimal order state observer based on the torque component of the vector control induction moter. Therefore, the torque controller is not affected by a load torque disturbance.

• 한국기계가공학회지
• /
• 제18권9호
• /
• pp.72-80
• /
• 2019

In this task, the tool dynamometer design and manufacture, and the Ansys S/W structural analysis program for tool attachment that satisfies the cutting force measurement requirements of the tool dynamometer system are used to determine the cutting force generated by metal cutting using 3-axis static structural analysis and the LabVIEW system. The cutting power in a cutting process using a milling tool for processing metals provides useful information for understanding the processing, optimization, tool status monitoring, and tool design. Thus, various methods of measuring cutting power have been proposed. The device consists of a strain-gauge-based sensor fitted to a new design force sensing element, which is then placed in a force reduction. The force-sensing element is designed as a symmetrical cross beam with four arms of a rectangular parallel line. Furthermore, data duplication is eliminated by the appropriate setting the strain gauge attachment position and the construction of a suitable Wheatstone full-bridge circuit. This device is intended for use with rotating spindles such as milling tools. Verification and machining tests were performed to determine the static and dynamic characteristics of the tool dynamometer. The verification tests were performed by analyzing the difference between strain data measured by weight and that derived by theoretical calculations. Processing test was performed by attaching a tool dynamometer to the MCT to analyze data generated by the measuring equipment during machining. To maintain high productivity and precision, the system monitors and suppresses process disturbances such as chatter vibration, imbalances, overload, collision, forced vibration due to tool failure, and excessive tool wear; additionally, a tool dynamometer with a high signal-to-noise ratio is provided.

• 항공우주시스템공학회지
• /
• 제12권2호
• /
• pp.30-36
• /
• 2018

본 연구에서는 무인복합형 회전익기 연구의 일환으로 축소형 Tip Jet 로터 시험장치를 개발하였으며, 이를 이용하여 Tip Jet 로터에 대한 성능 및 동특성 연구를 수행하였다. 축소로터는 시험장 여건 및 공압조건 등을 고려하여 2m급이 되도록 하였으며, 압축공기를 이용하여 구동된다. 축소로터의 회전속도는 압축공기의 압력을 이용하여 조절되며, 별도의 하중측정부를 두어 회전 시 발생하는 추력과 각 방향의 하중 데이터를 획득하게 된다. 동특성 시험을 위해 별도의 유압 가진기가 장착되어 있으며, 로터 가진 시 발생하는 블레이드의 flap, lag 및 torsion 방향에 대한 동적 응답을 확인하기 위해, 각 블레이드의 익근부에는 full-bridge strain gage를 부착하였다. 성능 및 동특성 시험은 로터 회전수 및 블레이드 피치각을 변경해가며 실시되었다. 아울러 시험 결과의 유효성을 확인하기 위해 CAMRAD II 해석 결과와 비교하였다.

• 한국정밀공학회지
• /
• 제31권10호
• /
• pp.905-911
• /
• 2014

A Loss-in-Weight (LIW) feeder, a type of automated measuring device, is a continuous feeder used in many mass production industries. Due to its versatility, there have been constant demands of LIW feeders in food production supply lines as well as chemical and pharmaceutical industries. In this paper, the process of designing a LIW feeder system with better performance will be examined and compared with commercial products. This system is characterized by low pass Butterworth filter and feed forward PI control. The filter is for noise disposal caused by dynamic condition of a LIW feeder. The feed forward PI control, based on linearity feature of feeders, is adequate for stable driving of the system. At the end, a possible evaluation method of LIW system will be proposed to verify the specific achievement of this paper.

• Earthquakes and Structures
• /
• 제12권5호
• /
• pp.479-487
• /
• 2017

Frictional dampers are used in structural engineering as means of passive control. Meanwhile, frictional damper shave a disadvantage compared to viscous rivals since the slippage force must be exceeded to activate the device, and cannot be ideal full range of possible events. The concept of semi-active control is utilized to overcome this shortcoming. In this paper, a new semi-active frictional damper called Smart Adjustable Frictional (SAF) damper is introduced. SAF damper consists of hydraulic, electronic units and sensors which are all linked with an active control discipline. SAF acts as a smart damper which can adapt its slippage threshold during a dynamic excitation by measuring and controlling the structural response. The novelty of this damper is, while it controls the response of the structure in real time with acceptable time delay. The paper also reports on the results of a series of experiments which have been performed on SAF dampers to obtain their prescribed hysteretic behavior for various control algorithms. The results show that SAF can produce the desired slippage load of various algorithms in real time. Numerical models incorporating control simulations are also made to obtain the hysteretic response of the system which agrees closely with test results.

• 한국정보통신학회논문지
• /
• 제17권11호
• /
• pp.2479-2485
• /
• 2013

본 논문에서는 순차 바이어스를 이용한 반도체 레이더용 SSPA를 설계 하였다. 전력증폭기의 상승/하강 바이어스 지연에 의해 발생되는 신호의 왜곡을 제거하기 위하여 가변확장 펄스 생성기를 적용하였다. 최적화된 임피던스 매칭회로는 GaN-전력 소자의 높은 효율을 갖기 위하여 로드-풀 방식을 통한 마이크로파 특성 측정으로 설계되었다. 설계된 SSPA는 X밴드 반도체 레이더에 적용하기 위하여 전치 증폭기, 구동 증폭기 그리고 주 증폭기의 3개의 단으로 구성되었다. 그 결과로 200W 출력 펄스 최대 53.67dBm을 가지고 평균 52.85dBm의 SSPA를 만들 수 있었다. 본 논문에 제시된 반도체 펄스 압축 레이더 트랜시버 모듈의 최적화 설계는 추가적인 디지털 레이더에 대한 연구를 통해 소형화와 동작향상이 가능하다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1995년도 가을 학술발표회 논문집
• /
• pp.15.2-22
• /
• 1995

Evaluating stiffness of near-surface materials has been one of the critically important tasks in many civil engineering works. It is the main goal of geotechnical characterization. The so-called deflection-response method evaluates the stiffness by measuring stress-strain behavior of the materials caused by static or dynamic load. This method, however, evaluates the overall stiffness and the stiffness variation with depth cannot be obtained. Furthermore, evaluation of a large-area geotechnical site by this method can be time-consuming, expensive, and damaging to many surface points of the site. Wave-propagation method, on the other hand, measures seismic velocities at different depths and stiffness profile (stiffness change with depth) can be obtained from the measured velocity data. The stiffness profile is often expressed by shear-wave (S-wave) velocity change with depth because S-wave velocity is proportional to the shear modulus. that is a direct indicator of stiffiiess. The crosshole and downhole method measures the seismic velocity by placing sources and receivers (geophones) at different depths in a borehole. Requirement of borehole installation makes this method also time-consuming, expensive, and damaging to the sites. Spectral-Analysis-of-Surface-Waves (SASW) method places both source and receivers at the surface, and records horizontally-propagating surface waves. Based upon the theory of surfacewave dispersion, the seismic velocities at different depths are calculated by analyzing the recorded surface-wave data. This method can be nondestructive to the sites. However, because only two receivers are used, the method requires multiple measurements with different field setups and, therefore, the method often becomes time-consuming and labor-intensive. Furthermore. the inclusion of noise wavefields cannot be handled properly, and this may cause the results by this method inaccurate. When multi-channel recording method is employed during the measurement of surface-waves, there are several benefits. First, usually single measurement is enough because multiple number (twelve or more) of receivers are used. Second, noise inclusion can be detected by coherency checking on the multi-channel data and handled properly so that it does not decrease the accuracy of the result. Third, various kinds of multi-channel processing techniques can be applied to f1lter unwanted noise wavefields and also to analyze the surface-wavefields more accurately and efficiently. In this way, the accuracy of the result by the method can be significantly improved. Fourth, the entire system of source, receivers, and recording-processing device can be tied into one unit, and the unit can be pulled by a small vehicle, making the survey speed very fast. In all these senses, multi-channel recording of surface waves is best suited for a routine method for geotechnical characterization in most of civil engineering works.