• The Journal of the Korea institute of electronic communication sciences
• /
• v.8 no.4
• /
• pp.611-617
• /
• 2013

Although tuberculosis can be recovered if patients take medicine consistently, Korea shows significantly high rate in terms of incident rate and death rate of the tuberculosis patients. Considering such a situation, this paper has developed a smart pillbox that facilitates for patients requiring a long-term administration to take medicine in a regular and consistent manner. The developed smart pillbox is equipped with a load cell that can measure the weight in unit of 0.1g so that it can determine whether or not the medicine is dispensed out of itself. In addition, a software has been developed to determine the status of patient's taking medicine based on the measurement result.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.13 no.3
• /
• pp.503-508
• /
• 2018

This study describes the design and implementation of EGSE for Digital Satellite Communication. The EGSE is a equipment that evaluates digital satellite communication and requires precise and accurate measurement. EGSE consists of a PLDIU and IIU(Instrument Interface Unit), Up/Down converter for SHF band, Modems to verify the Digital Satellite Communication. The EGSE was used for performance verification and space environment test such as thermal vacuum after developing digital satellite communication.

• Korean Journal of Biological Psychiatry
• /
• v.24 no.4
• /
• pp.196-203
• /
• 2017

Objectives Childhood trauma increases substantial risks for later developing not only mental health issues including psychotic illnesses such as schizophrenia but also physical illness. In this study, possible associations of childhood trauma with metabolic syndrome and physical heath indices were tested among outpatients with schizophrenia. Methods A final sample of 46 adult outpatients with schizophrenia was recruited from an outpatient psychiatric unit of Hanyang University Guri Hospital. Participants completed the Childhood Trauma Questionnaire-Short Form (CTQ-SF), laboratory tests and physical measurement including Body Mass Index (BMI) and Waist to hip ratio (WHR). The Clinical Global Impression (CGI) scale and the Global Assessment of Functioning scale (GAF) were also administered. Results We did not find significant correlations between total scores of childhood trauma and any of these variables, but physical neglect was negatively associated with BMI (r = -0.329, p = 0.026) and waist circumference (r = -0.304, p = 0.040). Conclusions In this preliminary study, we noted that subtypes of childhood trauma could contribute to physical health status separately. Clinicians need to consider the possibility that childhood trauma may affect physical health as well as psychological aspect of schizophrenic illness.

• Proceedings of the KSME Conference
• /
• 2001.06c
• /
• pp.507-512
• /
• 2001

In this work, tool holder system has been designed and builted to measure cutting forces in diamond turning. This system design includes a 3-component piezo-electric tranducer. Initial experiments with tool holder system included verification of its predicted dynamic characteristics as well as a detailed study of cutting parameters. Tool holder system is modeled by considering the element dividing, material properties, and boundary conditions using MSC/PATRAN. Mode and frequency analysis of structure is simulated by MSC/NASTRAN, for the purpose of developing the effective design. Many cutting experiments have been conducted on 6061-T6 aluminum. Tests have involved investigation of velocity effects, and the effects of depth and feedrate on tool force. Forces generally increase with increasing depth of cut. Increasing feedrate does not necessarily lead to higher forces.

• Journal of Korean society of Dental Hygiene
• /
• v.20 no.1
• /
• pp.73-83
• /
• 2020

Objectives: This study aimed to measure the knowledge of dental hygienists regarding dental waste, and identify the relationship between general characteristics and infection control characteristics. Methods: This study was conducted using a self-reported questionnaire in 250 dental hygienists. The questionnaire consisted of 21 items: storage container (5 items), storage locations (5 items), storage period (9 items), and storage method (3 items). The collected data were analyzed using the t-test and analysis of variance. Results: The education experience of infection management within the last year was reviewed for significant differences among dental hygienists regarding storage container and storage periods (p<0.05). Statistically significant differences were observed regarding the knowledge of storage container, storage locations, storage period, and storage method among the enrolled dental hygienists (p<0.05). Conclusions: This study examined the necessity of developing conservative education and job education programs to improve the knowledge level of dental hygienists regarding dental waste management.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.10 s.241
• /
• pp.1092-1100
• /
• 2005

In the present study, characteristics of steady state laminar flows of a straight duct connected to a 180$^{o}$ curved duct were examined in the entrance region through experimental and numerical analyses. For the analysis, the governing equations of laminar flows in the Cartesian coordinate system were applied. Flow characteristics such as velocity profiles and secondary flows were investigated numerically and experimentally in a square cross-sectional straight duct by the PIV system and a CFD code(STAR CD). For the PIV measurement, smoke particles produced from mosquito coils. The experimental data were obtained at 9 points dividing the test sections by 400 3m. Experimental and numerical results can be summarized as follows. 1) Reynolds number, Re was increased, dimensionless velocity profiles at the outer wall were increased due to the effect of the centrifugal force and secondary flows. 2) The intensity of a secondary flow became stronger at the inner wall rather than the outer wall regardless of Reynolds number. Especially, fluid dynamic phenomenon called conner impact were observed at dimensionless axial position, x/D$_{h}$=50.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.37-41
• /
• 2007

Fast Fourier Transformation(FFT) is one of the most useful way to analyze response signal for the purpose of grasping the dynamic characteristics of system. Excitation is a factor or process making noise or vibration. It's typical and simple experimental method widely used for catching hold of dynamic peculiar characters and modal behaviors of system by frequency analysis. There are harmonic excitation, impact excitation, random excitation, sweep excitation, chirp excitation and so on as the ideal method in an experiment using exciter. In this thesis, excitation testing module for NI-PXI equipment is developed. The analyzing module is developed with LabVIEW tool. A user can generate each waveform for shaking a structure and see quickly and easily modal shape of system with this module. This developed module will be expected to build up more convenient and serviceable measurement system.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.10-14
• /
• 2005

This report deals with a feeding system of the Coaxal grinding machine, processing optical ferrule. This report also examines the applicability of using the feeding system for the Coaxial grinding machine, by mean of conducting performance estimation. The results are as follow; Repeatability of regulating wheel is $17{\mu}m$, R/W rotation accuracy is between $30\;\~\;40{\mu}m$. This means 'Rotation accuracy' is lower than the concentricity level. Backlash generation level at the feeding system of the grinding wheel is under $1{\mu}m$, thereby positioning accuracy is controlled within $2{\mu}m$ In terms of repeatability, you can find occasional error at the returning process from the starting point. This error is resulted from the measurement tolerance of the starting point sensor. We will get the repeatability level under control by $1{\mu}m$, through improving the soft-ware used and up-grading the sensor at the starting point.

• Proceedings of the Korea Society for Industrial Systems Conference
• /
• 1999.12a
• /
• pp.739-745
• /
• 1999

This paper forcuses on the measurement of increased work efficiency expected from the factory automation through random interactions of the organizational behavioral factors whose attributes can be changed with the implementation of the factory automations. Specifically the work reported here is concerned with modeling and analyzing the random interrelationships among the organizational behavioral factory which factory automation will have impact on throughout the time horizon of its implementation in terms of productivity. In addition, it is also concerned with developing a stochastic continuous simulation model to be used to assess the impact of factory automations.

• Korean Chemical Engineering Research
• /
• v.43 no.1
• /
• pp.181-185
• /
• 2005

The flash point is one of the most important combustible properties used to determine the potential for fire and explosion hazards of industrial material. An accurate knowledge of the flash point is important in developing appropriate preventive and control measures in industrial fire protection. The flash points for the n-butanol+n-propionic acid and n-propanol+n-propionic acid systems were measured by using Tag open-cup apparatus(ASTM D 1310-86). The experimental data were compared with the values calculated by the laws of Raoult and van Laar equation. The calculated values based on the van Laar equation were found to be better than those based on the Raoult's law.