• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.1
• /
• pp.58-66
• /
• 2003

This paper discusses the practical issue of the bias estimation of the KOREASAT ground tracking data. First, a batch filter based orbit determination algorithm including the turn around range measurement in addition to the range, azimuth and elevation measurement is presented. Then the estimation performance is analyzed through simulation studies. Additionally, this paper proposes a tracking antenna bias estimation strategies using accurately tuned secondary ground tracking station. Finally the relationship between antenna biases are analyzed to give comprehensive tool for estimation results evaluation.

• Geomechanics and Engineering
• /
• v.17 no.6
• /
• pp.527-534
• /
• 2019

There have been developed a number of methods to assess the abrasivity of rock materials with the increased use of mechanized rock excavation. These methods range from determination of abrasive and hard mineral content using petrographic thin section analysis to weight loss or development of wear flat on a specified cutting tool. The Cerchar abrasivity index (CAI) test has been widely accepted for the assessment of rock abrasiveness. This test has been considered to provide a reliable indication of rock abrasiveness for isotropic rocks. However, a great amount of rocks in nature are anisotropic. Hence, viability assessment of Cerchar abrasivity test for the anisotropic rocks is investigated in this research. The relationship between CAI value and quartz content for the isotropic rocks is well known in literature. However, a correlation between EQ, F-Schimazek value, Rock Abrasivity Index (RAI) and CAI of anisotropic rocks such as phyllite was done first time in literature with this research. The results obtained with this research show F-Schimazek values and RAI values should be considered when determination of the abrasivity of anisotropic rocks instead of just using Cerchar scratch test.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.10
• /
• pp.2489-2496
• /
• 2014

The existing ship repair tool management system based on hand writing has many problems such as frequent loss of tool and overdue. To solve this problem, same systems have adopted the bar-code system. However, the systems can't cope with a problem to substitute spurious tool for genuine one on bar-code damage. Therefore, additional validation steps are necessary in order to manage expensive ship repair tool. In this paper, we propose an image comparison method for ship repair tool management. To be more concrete, we propose a normalization method and determination conditions for image comparison to use characteristics of mobile device. The normalization method makes use of the characteristics of mobile device that provides functions of real time recording, overlapping and cropping images. The proposed method applies three conditions(sum of inner angles, size of angle, position of corner coordinates) into the comparison module. The implemented system shows good performance on change direction, lighting, size and etc. The accuracy is more than 95%.

• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 2004.04a
• /
• pp.275-278
• /
• 2004

The geo-referencing of satellite imagery is a key task in remote sensing. GCPs are points the position of which is known both in the image and in the supporting maps. Mapping function makes the determination of map coordinates of all image pixels possible. Generally manual operations are done to identify image points corresponding to the points on a digital topographic map. In order to accurately measure ground coordinates of GCPs, differential global positioning system (DGPS) surveying are used. To acquire the sufficient number of well distributed GCPs is one of the most time-consuming and cost-consuming tasks. This paper describes the procedure of automatically extracting GCOs using GCP database. GCP image chips and image matching technique are used for automatic extraction of GCPs. We developed image processing tool for making image chip GCPs and Web Server for management of GCPs.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.3 no.2
• /
• pp.3-9
• /
• 2004

The main objectives of this paper are to determine optimum cutting conditions using experimental design method to manufacture pedicle screws. Generally, titanium alloys are known as difficult-to cut materials. In the machining of titanium alloy, high cutting temperature and strong chemical affinity between the tool and the work material are generated because of Its low thermal conductivity and chemical reactivity. Such phenomenon cause increase of tool wear and deterioration of surface quality. Thus, in this paper, required experimental investigations are performed to evaluate the machinability of titanium materials With tungsten carbide tools Required simulation and experiments are performed, and the results are investigated.

• Journal of Korean Society for Quality Management
• /
• v.26 no.4
• /
• pp.51-64
• /
• 1998

Mean shifts may be found in tool wear in machining, drawing, stamping and moulding operations, which make the process quality level deteriorate over time. In such situations, it is necessary to reset or readjust the manufacturing process at regular time basis or by inspection to prevent defective items produced. Although the deterioration rate may be assumed to be linear in a production cycle, there are many cases where the rate varies after resetting due to the variation of tool characteristics or by using the resharpened tools. In such cases, the deterioration rate should not be assumed to be a deterministic constant but a random variable. This paper is to find an optimal resetting period and quality level for such production processes.

• Korean Journal of Computational Design and Engineering
• /
• v.2 no.3
• /
• pp.186-194
• /
• 1997

This paper describes new methods to minimize the cutting time in zigzag milling operation of two dimensional polygonal surfaces. Previous works have been focused on mainly experimental approaches by considering some machining parameters such as, spindle speed, depth of cut, cutter traverse rate, cutter diameter, number of teeth, tool wear, life of tool, and so on. However, in this study, we considered two geometrical factors one by one in order to see the effect separately, which are the length of cut and the number of cutter traverse. In an N-sided concave or convex polygon, an algorithm has been developed which minimize the total length of cut. Also, a heuristic approach was used to minimize the number of cutter traverse.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 2000.04a
• /
• pp.401-404
• /
• 2000

최근 제조환경은 다양한 소비자의 요구, 제품의 짧은 수명 주기, 치열한 국내외 경쟁 등으로 특징 지워진다. 이러한 제조환경에 적응하기 위하여 FMS(flexible manufacturing systems)에서 기계의 종류는 다기능 공작기계(versatile machine)로 구성되고, 공구는 빠른 공구 이동장치(tool delivery system)에 의하여 제어되는 추세에 있다. 공구 이동장치를 이용하여 가공 중에 필요한 공구를 다른 기계 또는 공구 저장장치로부터 공급하는 동적 공구할당 전략하의 FMS 에서는 공구의 가용여부(작업 일정계획)를 고려한 작업순서 결정이 중요한 문제이다. 본 연구에서는 동적 공구할당 전략하의 FMS 에서 한 부품 또는 한 셋업에서 공구대기시간을 줄이는 방향으로 공구할당을 수행하는 작업순서 알고리즘을 제안하고, 시뮬레이션 실험을 통하여 다른방법으로 공구할당을 수행하는 알고리즘과 비교함으로써 본 작업순서 알고리즘의 우수성을 입증한다.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.03b
• /
• pp.161-164
• /
• 1999

In order to investigate the effect of punching condition on the stretch flange formability of sheet for deep drawing hole expansion tests at various edge condition were done. Edge conditions were changed by altering tool clearances artifical defects grinding and deburring. For a determination of optimum edge condition of side panel of automobile punched section analysis and forming results were studied and the laboratory test results were used. In case of considered side panel tool clearance should be less than 15% and punched edge should be uniform without defects for safe forming

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2001.05a
• /
• pp.692-695
• /
• 2001

The EMFG(Extended Mark Flow Graph) is not only a powerful tool to. designing the discrete-event system conceptually or specifically but also a good representation tool for implementing the system directly. We present a transitions-firing process and automatic changes of the number of marks in each box as a firing determination algorithm with the incident matrix and the state transition equation. The convenient analysis and design of a system as well as Computer Aided Design is possible because the operations of an EMFG ran be represented in the mathematical analysis with ease.