• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.965-969
• /
• 1997

Due to the high feed rate,high speed machining (HSM) provide a great potential of rationalization for the machining Dies and Moulds. But determination of cutting condition is very difficult, because cutting mechanism of high speed machining is very complicated,especially using ball end-mill. This paoer gives a report on selection of the optimal cutting condition to improve the machining efficiency, And optimal machining condition is determined through the cutting force, FFT analysis of cutting force and surface roughness according to the cutting condition. Based on this experiment result,wear process and machining characteristics are evaluated.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.04a
• /
• pp.109-114
• /
• 2000

A new method for the determination of camera system rotation and translation from in 3-D space using recursive least square method is presented in this paper. With this method, the calculation of the equation is found by a linear algorithm. Where the equation are either given or be obtained by solving five or more point correspondences. Good results can be obtained in the presence if more than the eight point. A main advantage of this new method is that it decouple rotation and translation, and then reduces computation. With respect to error in the solution point number in the input image data, adding one more feature correspondence to required minimum number improves the solution accuracy drastically. However, further increase in the number of feature correspondence improve the solution accuracy only slowly. The algorithm proposed by this paper is used to make camera system rotation and translation easy to recognize even when camera system attached at end effecter of six degrees of freedom industrial robot manipulator are applied industrial field.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.18 no.2
• /
• pp.214-220
• /
• 2009

The spindle is the main component in machine tools. The static and dynamic stiffness of the spindle directly affect the machining productivity and surface integrity of the workpiece. The static and dynamic stiffness of the spindle depend on the shaft size, bearing arrangement, bearing span length, and so on. Therefore, the selection of shaft size and bearing span length are important to improve the spindle stiffness. This paper presents the determination of shaft size and bearing span length in spindle design step. In order to select the optimal bearing and built-in motor locations with constraint conditions, the extreme vertices design was applied. The results show that extreme vertices design is usable for spindle design with design constraints.

• Journal of Korean Society for Quality Management
• /
• v.19 no.1
• /
• pp.151-162
• /
• 1991

The purpose of this study is to propose a facility layout design algorithm based on artificial intelligence concept, and then to develop a computer program which is more practical than any other conventional facility layout design systems. The algorithm is composed of five step layout procedures; knowledge and data input, knowledge interpretation, priority determination, inference of layout design, and evaluation, In the step of priority determination, the algorithm is divided into single row and multi row layout problem. In the step of inference of layout design, alternatives are generated by constraints-directed reasoning and depth first search method based on artificial intelligence concept. Alternatives are evaluated by the moving cost and relationship value by interactive man-machine interface in the step of evaluation. As a case study, analytical considerations over conventional programs such as CRAFT and CORELAP was investigated and compared with algorithm propsed in this study. The proposed algorithm in this study will give useful practical tool for layout planner. The computer progran was written in C language for IBM PC-AT.

• Korean Journal of Pharmacognosy
• /
• v.32 no.2 s.125
• /
• pp.89-92
• /
• 2001

Geniposide, an iridoid glucoside, was isolated from the cortex of Eucommia ulmoides by repealed silica gel chromography and identified by its spectral data. The quantitative determination of geniposide with HPLC has been developed and this method provided a tool for standardization of the commercial Eucommiae Cortex.

• International Journal of Aeronautical and Space Sciences
• /
• v.6 no.2
• /
• pp.17-22
• /
• 2005

As one of validation tool for attitude determination system, we have used various constraints using priori information which is known through base vector set up. However these conventional constraints cannot guarantee validity in terms of final solutions such as Euler angle. So we suggest attitude boundary concept to verify the final attitude solution on the flying airplane, it is based on the combination of velocity based attitude estimation technique and ambiguity resolution. we can say it can check invalid solution effectively at just one epoch without repeatability test of resolved cycle ambiguity. In this paper we show that the suggested constraint can effectively reject incorrectly resolved cycle ambiguity the conventional constraints have missed.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.11 no.6
• /
• pp.17-23
• /
• 2002

A new 3D micromachining method called Hole Area Modulation(HAM), has been introduced to enhance the current micromachining technology. In this method, information on the depth of machining is converted to the sizes of small holes in the mask. The machining is carried out with a simple 2D movement of the workpiece. This method can be applied for machining various kinds of microcavities in various materials. In this paper, a machematical model for excimer laser micromachining based on HAM and also determination of optimal laser ablation conditions(width hole radius, step size, path, etc.) is performed by Genetic Algorithm(GA).

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.32 no.5
• /
• pp.374-381
• /
• 2008

The correlation coefficient method, which was proposed by our research group, is applied to digital particle holography to locate the focal plane of particles. It uses the fact that the correlation coefficient is maximum at the focal plane. The factors influencing this method are discussed with a numerical simulation of holograms. For real holograms, the Wiener filter was proposed to process both recorded holograms and reconstructed images. The application results using the dot array target showed that the Wiener filter is a very effective tool for processing holography-related images. The effects of the dot size and the object distance on the errors in the determination of the focal plane by the correlation coefficient method were investigated by using the calibration target.

• Bulletin of the Korean Chemical Society
• /
• v.27 no.11
• /
• pp.1780-1784
• /
• 2006

Cloud point extraction was used to extract mefenamic acid (MF) from human urine, and spectrofluorimetry and spectrophotometry were used to analyze extracted MF. The variables affecting extraction and phase separation, i.e. HCl and Triton X-114 concentration, temperature and time of equilibration, were optimized. Under the experimental conditions used the limit of detection for extraction of 25 mL of sample was 0.006 and 0.045 mg $L^{-1}$, with relative standard deviations of 2.52 and 1.45% (n = 5) for spectrofluorimetric or spectrophotometric methods, respectively. Good recoveries in the range of 95-107% were obtained for spiked samples. The proposed methods were applied to the determination of MF in human urine.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.5
• /
• pp.435-440
• /
• 2003

The electron-atom collision studies have been essentially used for testing and developing suitable theories of the scattering and collision processes, and for providing a tool for obtaining detailed information on the structure of the target atoms and molecules and final collision products. And, the development of that has also been strongly motivated by the need for electron collision data in such fields as laser Physics and development, astrophysics, Plasma devices, upper atmospheric processes and radiation physics. The concept and the Principle of determination of the electron collision cross sections for atoms and molecules by using the present electron swarm method are explained.