• The KSFM Journal of Fluid Machinery
• /
• v.14 no.2
• /
• pp.47-51
• /
• 2011

This paper describes the shape optimization of a blower impeller used for a refuse collection system. Two design variables, which are used to define the blade angles of an impeller, are introduced to increase the blower performance. A blower efficiency is selected as an object function, and the shape optimization of the blade angles is performed by a response surface method (RSM). Three-dimensional Navier-Stokes equations are introduced to analyze the internal flow of the blower and to find the value of object function for the training data. Relatively good agreement between experimental measurements and numerical simulation is obtained in the present study. Throughout the shape optimization, blower efficiency for the optimal blade angles is successfully increased up to 3.6% compared with that of reference at the design flow rate. Detailed flow field inside the turbo blower is also analyzed and discussed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1418-1421
• /
• 2003

The Vacuum circuit breaker is a kind of power circuit breaker and protect electric devices from over-current. In this paper we built a dynamic model of VCB driving mechanism using ADAMS. The development of the new circuit breaker with less energy and more compactable mechanism is focused. Through the dynamic model, the concept design of the new circuit breaker with less energy and more compactable mechanism is proposed, and then the detailed design is carried out through the design process based on the dynamic model.

• Journal of Power System Engineering
• /
• v.20 no.3
• /
• pp.29-35
• /
• 2016

Because of the severe service environment of the large marine vessel, the fatigue strength and its evaluation play an important role in design and maintenance of marine crankshaft. The aim of this work is to investigate the probability distribution of fatigue lives in crank throw forged steel and to develop the methodology for estimation of the probabilistic design fatigue strength. Detailed studies were performed on the constant amplitude axial loading fatigue test. The experiments were controlled by stress ratio of -1 and 15Hz frequency for each stress level. The considerable variability of fatigue life was observed in each stress level under rigidly controlled constant fatigue testing conditions. The fatigue life of crank throw forged steel was well followed the log-normal and Weibull distribution. In addition, it can be used for the estimation of probabilistic design fatigue strength by using the proposed methodology.

• 한국전산유체공학회:학술대회논문집
• /
• 2011.05a
• /
• pp.173-178
• /
• 2011

Nowadays, SELENE-2 is under development for the moon explorer rover in Japan. AXS(Active X-ray Spectrometer) sensor development among the candidated payloads will be on going by the world-wide co-operation. The thermal design, analysis and test will be specially performed by Korean institutes. CFD techniques are used for the conceptual design and analysis. Thin-shell plate meshes being applied by Monte-Carlo Ray Tracing Method are generated for the thermal radiation analysis. Lumped capacity model is employed for the thermal conduction simulation of the AXS payload itself. Various shapes of the payload configuration with thermal boundary conditions are proposed and selected on the purpose of the analysis of the initial design. The results of the analysis are supposed to be used as the baseline for the further detailed design of the AXS payload in the future.

• Journal of Electrical Engineering and Technology
• /
• v.5 no.4
• /
• pp.561-570
• /
• 2010

This paper presents an advanced dynamic simulation model of a proton exchange membrane fuel cell for the optimal design of a fuel cell power conditioning system (FC-PCS). For the development of fuel cell models, the dynamic characteristics of the fuel cell are considered, including its static characteristics. Then, software fuel cell simulation is realized using Matlab-Simulink. Specifically, the design consideration of PCS (i.e., power semiconductor switch, capacitor, and inductor) is discussed by comparatively analyzing the developed simulator and ideal DC source. In addition, a cosimulation between the fuel cell model and PCS realized using the PSIM software is performed with the help of the SimCoupler module. Detailed analysis and informative simulation results are provided for the optimal design of fuel cell PCS.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1709-1714
• /
• 2004

Pressurization system of a 50m unmanned airship was manufactured according to the detailed design. In this paper. the whole procedures including system design. simulation and fabrication were described. The fabricated part were ground tested to check compliances with design requirements. Ground tests include operational tests, leakage tests, endurace tests and low temperature environmental tests. Results shows pressurization system of a 50m unmanned airship meets design requirements. Currently. pressurization system is installed to the KARI airship, Via 50m and performance verification through the flight tests are being conducted.

• Proceedings of the KIEE Conference
• /
• 2000.11b
• /
• pp.268-270
• /
• 2000

This paper deals with the design of transverse flux linear actuator based on the proposed design procedure. To satisfy requirement specifications, the initial model is designed by the equivalent magnet circuit and then the detailed design is achieved by Finite Element Method(FEM) using the equivalent reluctance 2D model. The effects of the design parameter on the static characteristics are investigated to increase the thrust.

• Journal of Ocean Engineering and Technology
• /
• v.25 no.2
• /
• pp.101-107
• /
• 2011

In view of the importance of material reduction because of the jump in oil and steel prices, structural design studies for lifting lugs were performed. Hundreds of thousands of such lifting lug structures are needed every year for ship construction. A direct design study was reviewed using the developed design system to increase the design efficiency and provide a way of directly inserting a designer's decisions into the design system process. In order to understand the design efficiency and convenience of a lug structure, parametric studies for prototype lug shapes were performed using the developed design system. From these design studies, various patterns of design parameters for the lug structure according to changes in the main plate length were examined. Based on these parametric study results, design guides were developed for more efficiently suggesting structural data for enormous lug structures. Additionally, a more detailed structural analysis through local strength evaluations will be performed to verify the efficiency of the optimum structural design for a lug structure.

• Journal of Ocean Engineering and Technology
• /
• v.36 no.2
• /
• pp.125-131
• /
• 2022

Structural design for shipbuilding is generally divided into three stages: the basic, detailed, and production designs, of which the production design is the most frequently revised among the three design stages. The revision involved in production design department was approximately 61% of the total 4,211 revision members and approximately 56% of the total 710 revision cases in the survey on the number of design revisions for nine ships. In this study, members and drawings with a high revision rate were investigated, and related design departments were identified. In addition, the work contents of the design department were analyzed to reduce the number of design revisions and three tasks are very frequently revised were selected. A survey was conducted with engineers engaged in the production design, after which, standards were proposed for the method of aggregating bills of materials, to employ macros to calculate the length of members and that of profile input data when reviewing drawings. Via the study, it was determined that the major causes of design revision are simple mistakes by engineers or lack of understanding on structural arrangement of basic members more than intricacies of prior design and high level specification. As a result of applying the proposed standards, it was confirmed that the design revision was reduced by approximately 40%.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.75-80
• /
• 2005

A design for the front section of an excavator requires kinematic and kinetic mechanism consideration for several configurations. Key parameters for an appropriate configuration can be obtained through a mechanical verification and numerical formulation with a design expert's know-how. In this paper, we propose a knowledge-based system with an expert-shell(CATIA) and Visual Basic to assist for the design of the front section of an excavator. The designers can achieve more efficient design through a CAD model, implemented design knowledge, and a user friendly interface. The implemented design knowledge is retrieved through the whole design process from an early design stage to a detailed design stage based on the multiple levels of abstraction scheme.