• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.3
• /
• pp.609-614
• /
• 2017

In this study, a new type of eccentric cam was used for the development of a small size reducer with a two-shift reduction ratio while maintaining the same volume as the existing one-shift speed reducer. Therefore, a two-shift speed reducer was designed using the concept of a continuously variable transmission applied to automobiles. The cam was designed to have an eccentric shape with a $180^{\circ}$ phase difference to act as a tensioner to minimize slip by squeezing the V-belt connected to the deceleration pulley and the acceleration pulley, respectively. The cam was designed to have a diameter of 35mm and an outer diameter of 18mm so that the outer portion of the v-belt could contact the cam perfectly. A pulley with a diameter of 50.8mm was installed on the low speed pulley input shaft for deceleration and a pulley with a diameter of 76.2mm was provided on the output shaft. In the high-speed pulley for acceleration, a pulley with a diameter of 76.2mm is provided on the input shaft, and a pulley with a diameter of 50.8mm is provided on the output shaft. Based on the design details, the power transmission efficiency test and the heating characteristics of the transmission were tested to verify the feasibility. In addition, through validation, the suitability of the reducer was demonstrated.

• Journal of the Korean Society for Railway
• /
• v.16 no.1
• /
• pp.7-13
• /
• 2013

A scaled version of a roller rig is developed to demonstrate the dynamic characteristics of a railway vehicle for academic purposes. This rig is designed based on Jaschinski's similarity law. It is scaled to 1/10 of actual size and allows 9-DOF motion to examine the up and down vibration of a train set. The test rig consists of three sub-hardware components: (i) a driving roller mechanism with a three-phase AC motor and an inverter, (ii) a bogie structure with first and second suspensions, and (iii) the vehicle body. The motor of the rig is capable of 3,600rpm, allowing the test to simulate a vehicle up to a maximum speed of 400Km/hr. Because bearings and joints are properly connected to the sub-structures, various motion analyses, such as a lateral, pitching, and yawing motion, are allowed. The slip motion between the rail and the wheel set is also monitored by several sensors mounted in the rig. After the construction of the hardware, an experiment is conducted to obtain the natural frequencies of the dynamic behavior of the specimen. First, the test rig is run and data are collected from six sets of accelerometers. Then, a numerical analysis of the model based on the ADAMS program is derived. Finally, the measurement data of the first three fundamental frequencies are compared to the analytical result and the validation of the test rig is conducted. The results show that the developed roller rig provides good accuracy in simulating the dynamic behavior of the vehicle motion. Although the roller rig designed in this paper is intended for academia, it can easily be implemented as part of a dynamic experiment of a bogie and a vehicle body for a high-speed train as part of the research efforts in this area.

• Journal of Korean Society of Transportation
• /
• v.18 no.5
• /
• pp.33-42
• /
• 2000

This Paper is a Part of research Project series to analyze unique traffic characteristics observable within weaving sections on urban freeways. The research objectives were to establish with headway distribution and maximum Passing volume on weaving sections the basis of weaving designs that can promote safety and efficiency. Until now, when one wants to check the maximum Passing volume on weaving sections, it is taken for granted using headway distribution of freeway basic section. However. it was suspected in this research that for weaving sections different form of headway distribution had better be used. To prove this, field surveys were made to count headway intervals which supposedly were influenced not only by freeway basic section flows but also by weaving flows and later on used to develop headway distribution for weaving sections. For validation of the developed headway distribution, $x^2$-test was applied to three different data set of observed headways, currently used headway distribution for basic sections(Pearson Type III distribution) and new headway distribution. The result indicated new headway distribution as the most appropriate distribution form. Also, maximum passing volume within weaving sections was calculated based on new headway distribution and compared with Drew's maximum Passing volume.

• Journal of Digital Convergence
• /
• v.16 no.3
• /
• pp.129-143
• /
• 2018

The purpose of this study was to examine the effect of donation expenditure details and the shift in awareness as a result of disclosure of donation expenditure details in order to promote constant donation by nonprofit organizations in the course of marketing activities. The first experiment was configured through $2{\times}2$ intergroup element design based on 2(feedback on donation expenditure details: available vs. unavailable) ${\times}$ 2(donation awareness: expenditure vs. exchange), and furthermore, MANOVA was performed. The results showed that the satisfaction with donation was higher when the donation expenditure details were disclosed(M=5.125, SD=0.437) and that the relation maintenance intention was higher(p<0.01) when the donation expenditure details were disclosed M=5.328, SD=0.459). In addition, the main effect was validated by using the bootstrapping method. The results of overall model validation showed that satisfaction & trust(=0.843, p<0.01) and satisfaction(=0.267, p<0.01) and trust(=0.691, p<0.01) had a positive(+) relationship. Based on aforesaid results, donors are expected to have greater trust if nonprofit organizations make effort to ensure transparent and detailed disclosure of information on expenditure of donations made by donors. Succeeding studies would need to investigate the effect that might vary depending on the type of feedback methods, etc.

• The Plant Pathology Journal
• /
• v.34 no.5
• /
• pp.381-392
• /
• 2018

Clavibacter michiganensis subsp. michiganesis (Cmm) is a quarantine-worthy pest in $M{\acute{e}}xico$. The implementation and validation of new technologies is necessary to reduce the time for bacterial detection in laboratory conditions and Raman spectroscopy is an ambitious technology that has all of the features needed to characterize and identify bacteria. Under controlled conditions a contagion process was induced with Cmm, the disease epidemiology was monitored. Micro-Raman spectroscopy ($532nm\;{\lambda}$ laser) technique was evaluated its performance at assisting on Cmm detection through its characteristic Raman spectrum fingerprint. Our experiment was conducted with tomato plants in a completely randomized block experimental design (13 plants ${\times}$ 4 rows). The Cmm infection was confirmed by 16S rDNA and plants showed symptoms from 48 to 72 h after inoculation, the evolution of the incidence and severity on plant population varied over time and it kept an aggregated spatial pattern. The contagion process reached 79% just 24 days after the epidemic was induced. Micro-Raman spectroscopy proved its speed, efficiency and usefulness as a non-destructive method for the preliminary detection of Cmm. Carotenoid specific bands with wavelengths at 1146 and $1510cm^{-1}$ were the distinguishable markers. Chemometric analyses showed the best performance by the implementation of PCA-LDA supervised classification algorithms applied over Raman spectrum data with 100% of performance in metrics of classifiers (sensitivity, specificity, accuracy, negative and positive predictive value) that allowed us to differentiate Cmm from other endophytic bacteria (Bacillus and Pantoea). The unsupervised KMeans algorithm showed good performance (100, 96, 98, 91 y 100%, respectively).

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.10 no.1
• /
• pp.25-36
• /
• 2008

When constructing subsea underground structures, the influence of high water and seepage pressure acting on the structures can not be neglected. Thus hydro-mechanical coupled analysis should be performed to estimate the behavior of the structures precisely In practice, relaxed rock load is generally used for the design of tunnel concrete lining. A method based on the distribution of local safety factor around a tunnel was proposed for the estimation of a height of relaxed rock mass ($H_{relaxed}$). In this study, the validation of the suggested method is investigated in the framework of hydro-mechanical coupled analyses. It was suggested that inducing inflow by pumping through a drainage well gave more reliable results than inducing inflow with shotcrete hydraulic characteristics in case of rock condition of Class III. In this study, therefore, inducing inflow by pumping through a drainage well are adopted in estimating $H_{relaxed}$ due to a tunnel excavation with the rock condition of Class I, III, and V. Also the estimated $H_{relaxed}$ results are compared with those of the existing suggested methods. As the result of this study, it is confirmed that estimating $H_{relaxed}$ based on the distribution of local safety factor around a tunnel can be effectively used even for the case of hydro-mechanical coupled analysis. It is also found that inducing inflow pumping through a drainage well gives more precise and consistent Hrelaxed of a subsea structure.

• Smart Structures and Systems
• /
• v.26 no.5
• /
• pp.575-589
• /
• 2020

For vibration control of stay cables in cable-stayed bridges, viscous dampers are frequently used, and they are regularly installed between the cable and the bridge deck. In practice, neoprene rubber bushings (or of other types) are also widely installed inside the cable guide pipe, mainly for reducing the bending stresses of the cable near its anchorages. Therefore, it is important to understand the effect of the bushings on the performance of the external damper. Besides, for long cables, external dampers installed at a single position near a cable end can no longer provide enough damping due to the sag effect and the limited installation distance. It is thus of interest to improve cable damping by additionally installing dampers inside the guide pipe. This paper hence studies the combined effects of an external damper and an internal damper (which can also model the bushings) on a stay cable. The internal damper is assumed to be a High Damping Rubber (HDR) damper, and the external damper is considered to be a viscous damper with intrinsic stiffness, and the cable sag is also considered. Both the cases when the two dampers are installed close to one cable end and respectively close to the two cable ends are studied. Asymptotic design formulas are derived for both cases considering that the dampers are close to the cable ends. It is shown that when the two dampers are placed close to different cable ends, their combined damping effects are approximately the sum of their separate contributions, regardless of small cable sag and damper intrinsic stiffness. When the two dampers are installed close to the same end, maximum damping that can be achieved by the external damper is generally degraded, regardless of properties of the HDR damper. Field tests on an existing cable-stayed bridge have further validated the influence of the internal damper on the performance of the external damper. The results suggest that the HDR is optimally placed in the guide pipe of the cable-pylon anchorage when installing viscous dampers at one position is insufficient. When an HDR damper or the bushing has to be installed near the external damper, their combined damping effects need to be evaluated using the presented methods.

• Asian-Australasian Journal of Animal Sciences
• /
• v.26 no.10
• /
• pp.1474-1483
• /
• 2013

The objective was to evaluate the use of prediction equations based on the chemical composition of feedstuffs to estimate the values of apparent metabolisable energy corrected for nitrogen balance (AMEn) of corn and soybean meal for broilers. For performance and carcass characteristics, 1,200 one-d-old birds (male and female) were allotted to a completely randomised factorial $2{\times}8$ (two genders and eight experimental diets) with three replicates of each sex with 25 birds. In the metabolism trial, 240 eight-d-old birds were distributed in the same design, but with a split plot in time (age of evaluation) with five, four and three birds per plot, respectively, in stages 8 to 21, 22 to 35, and 36 to 42 d of age. The treatments consisted of the use of six equations systems to predict the AMEn content of feedstuffs, tables of food composition and AMEn values obtained by in vivo assay, totalling eight treatments. Means were compared by Scott-Knott test at 5% probability and a confidence interval of 95% was used to check the fit of the energy values of the diets to the requirements of the birds. As a result of this study, the use of prediction equations resulted in better adjustment to the broiler requirements, resulting in better performance and carcass characteristics compared to the use of tables, however, the use of energy values of feedstuffs obtained by in vivo assay is still the most effective. The best equations were: AMEn = 4,021.8-227.55 Ash (for corn) combined with AMEn = -822.33+69.54 CP-45.26 ADF+90.81 EE (for soybean meal); AMEn = 36.21 CP+85.44 EE+37.26 NFE (nitrogen-free extract) (for corn) combined with AMEn = 37.5 CP+46.39 EE+14.9 NFE (for soybean); and AMEn = 4,164.187+51.006 EE-197.663 Ash-35.689 CF-20.593 NDF (for corn and soybean meal).

• Journal of Acupuncture Research
• /
• v.25 no.6
• /
• pp.77-93
• /
• 2008

Objectives : Though there were many clinical studies of acupuncture effects they didn't have appropriate control group or use another therapy for control group. So, we didn't say it was true acupuncture effect, though subjects in clinical study improved. Recently several sham needles for control group were developed and validated. This study aimed at summarizing the validation studies of these needles and evaluating the control group of the acupuncture clinical study. Methods : Computerized literature searches were performed using 'acupuncture' and 'placebo or sham' with a limitation of the results to RCTs in Pubmed, Sciencedirect, NDSL, KISS, RISS. Data were extracted regarding study design, sample size, acupuncture point, stimulation form, credibility testing. And We have examined 106 acupuncture clinical studies published by Pubmed from January 1, 2005 to April 30, 2008. Data were extracted author's country, subject of study, type of study groups, type of control groups, type of blinding, difference between the results in the control groups. Results : Streitberger's placebo needle, Fink's sham needle, Park sham needle, Kim sham needle were developed. They were validated at domestic and abroad. But the results were deviation depending on the each of the researcher. They has shown that sample, acupuncture points, experiences or knowledge of acupuncture dependent on the results. Recent three years, acupuncture clinical trial had different results. Significant differences between Study group and control group emerged from using other therapy or non-treatment for control group. Many study has no significant differences using sham acupuncture for control groups. Conclusions : Acupuncture clinical studies need to meet several requirements. First of all, they require the basics of randomized controlled clinical studies such as blinding and the accurate implementation and description of randomization. And also need to research the unique circumstances of these studies such as the development of sham acupuncture and blinding method which differs from other clinical trials.

• Journal of Internet Computing and Services
• /
• v.17 no.2
• /
• pp.39-47
• /
• 2016

In software R&D artifacts including documents and program code are produced. There are two kinds of software R&D artifacts: Research artifacts and development artifacts. Research artifacts include software R&D planning document, annual report, final report, research note and so on. Software development artifacts include software requirements, software design description, testing plan, test report, and program code. It is important to verify the documents and to test code to check the direction of the R&D. Moreover, we should check relationships as such completeness and consistency between research and development artifacts. The verification and testing help project manager and researchers understand what they do during software projects. Therefore, in this study, we present a process to verify documents and program in software R & D. In the process we check documents produced in software R&D and test program code. We describe the process by using Essence elements including alpha, activity, and competency. We present a case study to show the effectiveness of the process.