• Journal of Advanced Marine Engineering and Technology
• /
• v.30 no.1
• /
• pp.109-115
• /
• 2006

An overview of 30 feet sailing yacht design is presented. with an emphasis on the factors contributing to start-up Popularization . After prescribing the configurations of the purposed yacht. the design of the hull form with a rudder and a keel, are schematically described. Also the determinations of the dimensions of the sail and rig are performed.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2005.06a
• /
• pp.818-823
• /
• 2005

An overview of 30 feet sailing yacht design is presented, with an emphasis on the factors contributing to start-up popularization. After prescribing the configurations of the purposed yacht, the design of the hull form with a rudder and a keel, are schematically described. Also the determinations of the dimensions of the sail and rig are performed.

• Journal of Korea Water Resources Association
• /
• v.52 no.3
• /
• pp.227-234
• /
• 2019

The vulnerability of urban disasters is increased with the rapid urbanization and industrialization, and the extreme rainfall event is increased due to the global climate change. Urban inundation is also increased due to the extreme rainfall event beyond the capacity limit of facility for the damage prevention. The underground detention vault and the underground drain tunnel are rapidly being utilized to prevent urban inundation. Therefore, the hydraulic review and design analysis of the inlet of the underground facility are important. In this study, the water level of the approach flow according to the inflow discharge is measured and the flow characteristic of the inlet (tangential and spiral) is analyzed. For the spiral inlet, the multi-stage is introduced at the bottom of the inlet to improve the inducing vortex flow at low discharge conditions. In case of the tangential inlet, the discharging efficiency is decreased rapidly with hydraulic jump in the high flow discharge. The rising ratio of the water level in the multi-stage spiral inlet is higher than the tangential inlet, but the stable discharging efficiency is maintained at low and high discharge conditions. And the empirical formula of water level-flow discharge is derived in order to utilize inlets used in this study.

• Journal of IKEEE
• /
• v.23 no.3
• /
• pp.762-767
• /
• 2019

The plane-wave shielding effectiveness is typically measured for horizontal and vertical polarizations using a linearly polarized antenna. However, this typical measurement method results in big evaluation fees due to very long measurement time as well as huge idle space for maintenance, these problems is more severe especially in large shielded enclosures such as EMP protection facilities to be built in indoor buildings and underground. This paper describes the design and fabrication process and results of a planar log-spiral antenna applicable to the evaluation of the electromagnetic shielding effectiveness of a large EMP protection facility. Since the proposed antenna has a circular polarization, there is no need to separately measure the horizontal and vertical polarizations. Therefore, the measurement time can be shortened by more than 1/2, and further, its small volume with a planar structure can reduce greatly idle space required for the maintenance.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.22 no.4
• /
• pp.35-40
• /
• 2022

This paper proposes an antenna that is located outside the PCB substrate of an electronic product to enable wireless communication in the ISM band. The PCB designed the T-shaped OPEN-STUB power supply line to be miniaturized so that it does not interfere with parts or interfere with design. The characteristics of the antenna were confirmed in the 2.4GHz and 5.8GHz bands using a T-shaped stub feeder and a spiral structure. The size of the antenna is 5mm in width × 6.5mm in length, and the thickness of the PCB is 1.2T. As a result of measurement of the manufactured antenna, it was possible to obtain a return loss of -10dB or more at 2.4GHz and 5.8GHz. In the E-plane, the gain was -4.45 dBi, and in the H-plane, the gain was -1.05 dBi. Therefore, the proposed small antenna for wireless communication showed excellent performance.

• Wind and Structures
• /
• v.37 no.4
• /
• pp.315-329
• /
• 2023

We investigated the wind characteristics in the near-surface layer during the landfall of Typhoon Mujigae (2015) based on observations from wind towers in the coastal areas of Guandong province. Typhoon Mujigae made landfall in this region from 01:00 UTC to 10:00 UTC on October 4, 2015. In the region influenced by the eyewall of the tropical cyclone, the horizontal wind speed was characterized by a double peak, the wind direction changed by >180°, the vertical wind speed increased by three to four times, and the angle of attack increased significantly to a maximum of 7°, exceeding the recommended values in current design criteria. The vertical wind profile may not conform to a power law distribution in the near-surface layer in the region impacted by the eyewall and spiral rainband. The gust factors were relatively dispersed when the horizontal wind speed was small and tended to a smaller value and became more stable with an increase in the horizontal wind speed. The variation in the gust factors was the combined result of the height, wind direction, and circulation systems of the tropical cyclone. The turbulence intensity and the downwind turbulence energy spectrum both increased notably in the eyewall and spiral rainband and no longer satisfied the assumption of isotropy in the inertial subrange and the -5/3 law. This result was more significant in the eyewall area than in the spiral rainband. These results provide a reference for forecasting tropical cyclones, wind-resistant design, and hazard prevention in coastal areas of China to reduce the damage caused by high winds induced by tropical cyclones.

• Proceedings of the KSMRM Conference
• /
• 1999.11a
• /
• pp.89-89
• /
• 1999

• Journal of Korean Association for Spatial Structures
• /
• v.20 no.3
• /
• pp.4-8
• /
• 2020

• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.2105-2107
• /
• 2004

In this study, Spiral inductors on the $SiO_2$/Si(100) substrate were fabricated by the magnetron sputtering method. Cu thin film with the thickness of 2 ${\mu}m$ was deposited on the substrate. Also we fabricated square inductors through the wet chemical etching technique. The inductors are completely specified by the turn width and the spacing between spirals. Both the width and spacing between spirals were varied from 10 to 60 ${\mu}m$ and from 20 to 70 ${\mu}m$, respectively. Inductance and Q factor dependent on the RF frequency were investigated to analyze performance of inductor arrays. Also, We recommend that the reasonable Q-factors, spec's turns and thickness of the coil for inductors cab be set to be ideal condition.

• Proceedings of the KIEE Conference
• /
• 2003.04a
• /
• pp.289-291
• /
• 2003

This paper deals with the design of a spiral micro inductor using LTCC(Low Temperature Cofired Ceramics) technology. The inductors using the LTCC technology have some prominent properties of high integration of circuits, high confidence and low cost comparing with previously fabricated thick-film inductors. In this paper, we designed a new spiral-type micro inductor comprising a magnetic material to improve the inductance and leakage flux. we, in addition, presented the simulation results for various shapes of the magnetic material in the micro inductor, Finally application of the micro inductor to the boost DC-DC converter is investigated.