• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.1
• /
• pp.23-30
• /
• 2016

Wake effects cause wind turbine generators (WTGs) within a wind power plant (WPP) to produce different levels of active power and subsequent reactive power capabilities. Further, the impedance between a WTG and the point of interconnection (POI)-which depends on the distance between them-impacts the WPP's reactive power injection capability at the POI. This paper proposes a voltage control scheme for a WPP based on the available reactive current of the doubly-fed induction generators (DFIGs) and its impacts on the POI to improve the reactive power injection capability of the WPP. In this paper, a design strategy for modifying the gain of DFIG controller is suggested and the comprehensive properties of these control gains are investigated. In the proposed scheme, the WPP controller, which operates in a voltage control mode, sends the command signal to the DFIGs based on the voltage difference at the POI. The DFIG controllers, which operate in a voltage control mode, employ a proportional controller with a limiter. The gain of the proportional controller is adjusted depending on the available reactive current of the DFIG and the series impedance between the DFIG and the POI. The performance of the proposed scheme is validated for various disturbances such as a reactive load connection and grid fault using an EMTP-RV simulator. Simulation results demonstrate that the proposed scheme promptly recovers the POI voltage by injecting more reactive power after a disturbance than the conventional scheme.

• Tribology and Lubricants
• /
• v.14 no.4
• /
• pp.15-22
• /
• 1998

Recently, the importance of variable displacement piston pump is increasing in industrial world. Especially, most consumers require various range of pressures and flow rates. Pressure compensator is a system controlling flow rate in piston pump at low cost and, therefore, satisfies the need of consumers. However, the system has serious problems, such as response and leakage. The response and leakage are affected by clearance between actuator piston and cylinder, roughness of surface, and spool overlap. In this paper, these effects are investigated experimentally, and optimal clearance and chamfer is obtained. While diameter of cylinder is fixed and diameter of actuator piston is changed in this experiment, response and leakage are measured. Also parameters such as roughness and processing accuracy are changed for piston of fixed clearance. Experimental setup modelled into several parts of actuator piston, cylinder, spool, and swash plate. Input pressure is changed by function generator and proportional valve. The result of this experiment shows that leakage increases very much in proportion to the increase of clearance, and especially leakage occurs enormously when clearance is more than 0.002. The response is not good because as clearance increases leakage increases and as clearance decreases viscous damping effect increases. Accordingly, it is found out that optimal clearance range exists for tile response, within about 0.0012∼0.0014, at this time. Futhermore, the better roughness and geometrical accuracy of actuator piston are, the smaller are leakage and friction. The paper informs that response and leakage are influenced by and geometrical accuracy of actuator piston, roughness of surface, and the clearance between actuator piston and cylinder, and that optimal design of actuator piston in the pressure compensator is possible.

• Nuclear Engineering and Technology
• /
• v.47 no.2
• /
• pp.204-211
• /
• 2015

Probabilistic safety assessment (PSA) has had a significant role in quantitative decision-making by finding design and operational vulnerabilities and evaluating cost-benefit in improving such weak points. In particular, it has been widely used as the core methodology for risk-informed applications (RIAs). Even though the nature of PSA seeks realistic results, there are still "conservative" aspects. One of the sources for the conservatism is the assumptions of safety analysis and the estimation of failure frequency. Surveillance, diagnosis, and prognosis (SDP), utilizing massive databases and information technology, is worth highlighting in terms of its capability for alleviating the conservatism in conventional PSA. This article provides enabling techniques to solidify a method to provide time- and condition-dependent risks by integrating a conventional PSA model with condition monitoring and prognostics techniques. We will discuss how to integrate the results with frequency of initiating events (IEs) and probability of basic events (BEs). Two illustrative examples will be introduced: (1) how the failure probability of a passive system can be evaluated under different plant conditions and (2) how the IE frequency for a steam generator tube rupture (SGTR) can be updated in terms of operating time. We expect that the proposed model can take a role of annunciator to show the variation of core damage frequency (CDF) depending on operational conditions.

• Journal of the Korean Solar Energy Society
• /
• v.34 no.2
• /
• pp.8-15
• /
• 2014

The objective of this paper is to suggest a design topology of permanent magnet synchronous generator with 2,000kW capacities for wind turbine. The suggested topology is to provide 3 split magnet PMSG instead of single magnet, and performed an analysis of eddy current loss and iron loss for suggested type using ansoft maxwell commercial program. The simulation results of suggested magnet type show there duction of eddy current loss as 13.87kW with loadless conditions and23.48kW with rated conditions, but iron loss for rotor yoke show the in creasing trend as2.2kW with loadless conditions and 0.2kW with rated conditions. The suggested 3 split maget type is to identified as more useful for 2,000kW PMSG.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.1
• /
• pp.11-15
• /
• 2011

In this paper, a methodology for the power control of a wind turbine, which is the variable-speed and variable-pitch (VSVP) control system, is introduced. This control methodology maximizes the capability of the turbine to extract maximum power from the wind in the regions with low wind speeds. Further, it regulates the wind-turbine power as the rated power in the case of the regions with high wind speeds. A simple drive train model is used to design the VSVP control system. The methodology for VSVP control is mechanized by controlling the generator torque and blade pitch. Finally, some simulation results for the VSVP control to a MW wind turbine are discussed in this paper.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.10
• /
• pp.865-871
• /
• 2014

This study was conducted with the aim of developing a venturi-type air supply system for a microbubble generator. In order to determine the influence of the varying geometry of the venturi tube on the flow characteristics, a computational fluid dynamics (CFD) simulation was performed using the commercial CFD software ANSYS CFX-15. Furthermore, in order to elucidate the effects of variation in major design dimensions such as the air supply hole size, position of holes, and number of holes on the air supply characteristics, two-phase multiflow CFD analysis was performed. The analysis results showed that the starting point of expansion on the venturi tube with 0.75 is the best hole position and that the air supply hole size and the number of holes are linearly proportional to the amount of air.

• Journal of IKEEE
• /
• v.8 no.1 s.14
• /
• pp.128-135
• /
• 2004

This paper proposes a phase measurement algorithm which is based on the recursive implementation of sliding-DFT. The algorithm is designed to have a robust behavior against the erroneous factors of frequency drift, additive noise, and twiddle factor approximation. The size of phase error caused by the finite wordlength implementation of DFT twiddle factors is shown significantly lower than that of magnitude error. The drastic reduction of the phase error is achieved by the exploitation of the quadruplet symmetry characteristics of the approximated twiddle factors in the complex plane. Four channel power-line phase measurement system is also designed and implemented based on the time-multiplexed sharing architecture of the proposed algorithm. The operation of the developed system is also verified by the experiment performed under the test environment implemented with the multi-channel function generator and the on-line interfaced host processor system. The proposed algorithm's features of phase measurement accuracy and its robustness against the finite wordlength effects can provide a significant impact especially for the ASIC or microprocessor based embedded system applications where the enhanced processing speed and implementation simplicity are crucial design considerations.

• Journal of Ocean Engineering and Technology
• /
• v.29 no.4
• /
• pp.317-321
• /
• 2015

Many kinds of generation systems have been developed to use ocean energy. Among these, with the use of an oscillating water column (OWC) for power generation is attracting attention. The OWC-type wave power generation system converts wave energy into electricity by operating a generator turbine with the oscillating water level in a column of water. There are two ways to convert wave power into electricity using an OWC. One uses a cross-flow turbine using the water level inside the OWC. The other method uses the flow of air in a Wells turbine, which depends on the water level. An experiment was carried out using a 2-D wave tank in order to minimize the number of empirical tests. The design factors were taken from Koo et al. (2012) and the experimental environment assumed by free surface motion. This paper deals with characteristics of two types of wave energy conversion systems combine with a breakwater. One model uses an air-driven Wells turbine and a cross-flow water turbine. The other type uses a cross-flow water turbine. Wave energy converters with OWCs have mostly been studied using air-driven Wells turbines. The efficiency of the cross-flow turbine was about 15% higher than that of the other model, and the water level of the OWC internal chamber for the cross-flow water turbine and air-driven Wells turbine was less than about 40% lower than the one using only the cross-flow water turbine.

• Journal of the Korean Operations Research and Management Science Society
• /
• v.20 no.2
• /
• pp.159-178
• /
• 1995

Supervisory control is an approach based on formal language. it is used to model and control discrete event systems in which each discrete event process is represented as an automation. A supervisor is a generator that switches control patterns in such a way that a given discrete evenet process behaves in obedience to various constraints. A flexible manufacturing cell (FMC) is one of discrete evenet systems. Functions necessary for the operation of an FMC are characterized by operational components and informational compoments. The operational components can be modeled using the finite state machines and the informational components can be modeled using the abstract formalism which describes supporting operations of the cell controller. In this paper, we addressed function required for FMC control specification, software engineering aspects on FMC control based on supervisory control, a concept of event queue for resolving synchronization problem, and complexity reduction. Based on the mathematical model of an FMC. we synthesized the controller by integrating a supervisor for FMC with control specification that specifies event-driven operation of the cell controller. The proposed control scheme is stable mathematically so that the system always behaves on a controlled way even under the existence of uncontrollable events. Furthermore, using an event queue concept, we can solve a synchronization problem caused by the violation of instantaneity assumption of supervisory control theory in real life situation. And also, we can propotype a control software rapidly due to the modularity of the proposed control scheme.

• Transactions on Electrical and Electronic Materials
• /
• v.10 no.6
• /
• pp.222-226
• /
• 2009

The objective of this study is to share multimedia contents included in existing digital devices and to solve the problems of an increase in installation fees and non-environmentally friendly interiors. This study designed a new digital signal transmitter and receiver using power line transmission and HDMI in order to solve the problems in the existing systems. The transmitter and receiver designed in this study used an AD9867BCPZ PLC chip in which the transmission came from digital signals originating in a PC, and the system architecture was configured so that the outputs signals were connected to a TV from the receiver. The experiment was implemented by adding a Video Test Generator, a USBPre external sound card, and Smaart Live 6 for analyzing the characteristics of the configured system. In the video test results, it was verified that communication was actively implemented, and the image quality showed a constant level from the measurement of the captured video. In the case of the sound, it was verified that more than 90% of the sound signals were normally transmitted and received from the examination of their phases and magnitudes. Thus, the performance of the system designed in this study was verified, which leads to the resolution of some of the problems found in current digital devices.