• Earthquakes and Structures
• /
• 제8권2호
• /
• pp.423-442
• /
• 2015

The effects of accidental eccentricity on the seismic response of four-storey steel buildings laterally stabilized by buckling restrained braced frames are studied. The structures have a square, symmetrical footprint, without inherent eccentricity between the center of lateral resistance (CR) and the center of mass (CM). The position of the bracing bents in the buildings was varied to obtain three different levels of torsional sensitivity: low, intermediate and high. The structures were designed in accordance with the seismic design provisions of the 2010 National Building Code of Canada (NBCC). Three different analysis methods were used to account for accidental eccentricity in design: (1) Equivalent Static Procedure with static in-plane torsional moments assuming a mass eccentricity of 10% of the building dimension (ESP); (2) Response Spectrum Analysis with static torsional moments based on 10% of the building dimension (RSA-10); and (3) Response Spectrum Analysis with the CM being displaced by 5% of the building dimension (RSA-5). Time history analyses were performed under a set of eleven two-component historical records. The analyses showed that the ESP and RSA-10 methods can give appropriate results for all three levels of torsional sensitivity. When using the RSA-5 method, adequate performance was also achieved for the low and intermediate torsional sensitivity cases, but the method led to excessive displacements (5-10% storey drifts), near collapse state, for the highly torsionally sensitive structures. These results support the current provisions of NBCC 2010.

• 한국전산구조공학회논문집
• /
• 제27권5호
• /
• pp.459-467
• /
• 2014

ILM 교량은 압출되는 동안 상부의 단면이 지간의 중앙부와 지점부를 모두 통과한다. 따라서 발생되는 최대 정모멘트 및 최대 부모멘트를 효과적으로 제어하기 위해서 압출추진코를 이용한다. 이 연구에서는 압출중 상부구조물에 발생하는 휨모멘트를 계산할 수 있는 다이아프램이 고려된 단순 해석식을 개발하였다. 또한 다이아프램이 고려된 압출추진코의 최적설계조건에 관하여 분석하였다. 단순 해석식을 MIDAS Civil과 비교한 결과 대부분의 경우 0.5%이하의 오차를 가지는 정확성을 확인하였다. 다이아프램의 영향을 고려했을 경우와 고려하지 않았을 경우 사례교량에서 최대 13%의 휨모멘트 차이를 보였다. 또한, 단순 해석식에 적용시킬 등가 등단면의 단위중량 및 평균강성값을 결정할 수 있는 기준을 제시하였다. 이 연구에서는 ILM 교량의 압출중 역학특성으로 인하여 부모멘트 최소화 조건만을 사용하는 것이 압출추진코 최적설계를 위한 효과적인 방법으로 판단하였다.

• 대한기계학회논문집A
• /
• 제34권6호
• /
• pp.771-780
• /
• 2010

본 논문에서는 제작이 용이한 십자형 구조를 기본구조로 사용하여 판스프링 고정단을 가진 유연한 6축 로드셀을 설계하였다. 이를 위하여 유한요소법해석을 이용하여 강체 고정단과 판스프링 고정단에 대한 변형 분석을 하였으며 이로부터 특성이 우수한 6축 힘/토크 센서를 설계하였다. 변형률 분포를 이용하여 각 축의 하중에 대한 출력변형률이 비슷한 수준이 되도록 스트레인 게이지 위치를 정하고 상호간섭 변형률이 최소화 되도록 이들로 연결된 브리지회로를 구성하였다. 강체 고정단 대신에 스프링판 고정단을 이용하면 고정 경계부의 조건을 변화시킬 수 있어서 십자형 로드셀의 특성을 획기적으로 개선시킬 수 있었다. 치수 변경을 통하여 설계된 6축 로드셀에 대한 상호 간섭오차는 모든 축에서 0으로 계산되었으며 각 축에서 발생하는 출력변형률 값도 $400\;{\mu}m/m$의 비슷한 수준으로 결정되었다.

• 한국지반공학회지:지반
• /
• 제6권3호
• /
• pp.13-30
• /
• 1990

본 연구에서는 깊은 기초의 내진설계에 적용하기 위해, 지진하중에 의한 말뚝기초의 응답을 산출하여 비교, 검토하였다. 본 연구에서 사용된 해석 방법은 Subgrade Reaction Theory 및 탄성해석법과 같은 유사정적 해석방법, Prakash및 Gazetas가 각각 제안한 동적 해석방법이며, 예제해석을 통해 말뚝의 최대 상대변위 및 최대 휨모멘트를 위의 각 방법을 이용해서 산출하였고, 그 결과를 각각 비교하였다. 또한 말뚝의 군효과를 근사적으로 고려하여 Novak에 의해 수행된 실험 결과와 비교하였다. 해석결과를 분석해 볼 때 Kaynia와 Kausel이 제안한 동적 Group Interaction Factor Approach 에 의한 땅법 및 Gazetas가 제안한 방법의 최대 상대변위는 실측치와 부합하게 산정되었으며, Prakash 가 제안한 방법과 정적 Group Interaction Factor Approach에 의한 변위 및 휨모멘트는 과대평가되었다. 그러므로, 말뚝의 내진설계시에 동적 Group Interaction Factor Approach와 결합한 유사정적해석 을 사용하고 Gazetas가 제안한 동적방법에 의해 이를 검토하는 것이 바람직하다.

• 건축역사연구
• /
• 제22권2호
• /
• pp.31-42
• /
• 2013

This study identifies the current status of hanok design process and required design information through individual survey and interview with hanok architects and builders to suggest a proposal. Current design system turns out to be a common design process not reflecting hanok's unique mechanism of production. The proposal consists of the alternative design process, 'Initial survey / Site and structural planning / Spatial layout and form / Openings, interior and exterior elements design / Detail design', containing the specialty of hanok's mechanism, and the lists of design information required in its each stage. The proposed design process also emphasizes the significance of consultation in a way of designing coordination, and classifies the specific contents for each consultation moments. The study is expected to contribute for architects including the group who are not specialized in hanok to improve the architectural quality by following the systematic design process. Also the design system provides a framework to organize the vast range of design information being recently developed in the technique-oriented area.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집C
• /
• pp.327-332
• /
• 2001

An experimental design technique is developed for estimating the moments of system response functions. It is easy to implement and provides accurate results compared with other traditional methods. It is based on the work of Taguchi, later improved by D'Errico and Zaino. The existing experimental techniques, however, is applicable only for normally distributed cases. In this article the three-level Taguchi method is extended to obtain optimum choice for levels and weights to handle nonnormal distributions. A systematic procedure for reliability analysis is then proposed by using the Pearson system and the narrow system reliability bounds. Illustrative examples including a tolerance optimization problem are shown very accurate comparing with those by Monte-Carlo simulations and the first-order reliability method.

• 한국농공학회:학술대회논문집
• /
• 한국농공학회 2002년도 학술발표회 발표논문집
• /
• pp.225-228
• /
• 2002

This research seeks to derive the design rainfalls through the L-moment with the test of homogeneity, independence and outlier of data on annual maximum daily rainfall in 38 Korean rainfall stations. To select the fit appropriate distribution of annual maximum daily rainfall data according to rainfall stations, applied were Generalized Extreme Value (GEV), Generalized Logistic (GLO) and Generalized Pareto (GPA) probability distributions were applied. and their aptness was judged Dusing an L-moment ratio diagram and the Kolmogorov-Smirnov (K-S) test, the aptitude was judged of applied distributions such as GEV, GLO and GPA. The GEV and GLO distributions were selected as the appropriate distributions. Their parameters were estimated Targetingfrom the observed and simulated annual maximum daily rainfalls and using Monte Carlo techniques, the parameters of GEV and GLO selected as suitable distributions were estimated and. dDesign rainfallss were then derived, using the L-moment. Appropriate design rainfalls were suggested by doing a comparative analysis of design rainfall from the GEV and GLO distributions according to rainfall stations.

• 한국농공학회:학술대회논문집
• /
• 한국농공학회 2003년도 학술발표논문집
• /
• pp.439-442
• /
• 2003

This study was conducted to choose optimal distribution and to estimate properly parameters for the derivation of design rainfall in Gamma Family. Design rainfall derived by Gamma Family Distributions were compared by the Relative Mean Errors(RME) and Relative Absolute Errors(RAE) for the consecutive durations of 1, 3, 6, 12, 24, 36, 48 and 72hr and 65 regions all over the regions except Cheju and Wulreung islands in Korea. Consequently, Design rainfall derived by Indirect Method of Moments in the Log-Pearson Type 3 distribution are seemed to be more reasonable than those of other distributions in Gamma Family.

• 제어로봇시스템학회논문지
• /
• 제22권3호
• /
• pp.177-185
• /
• 2016

This paper presents a method to design a controller for active suspension with 1-DOF decoupled models. Three 1-DOF decoupled models describing vertical, roll and pitch motions are used to design a controller in order to generate a vertical force, roll and pitch moments, respectively. These control inputs are converted into active suspension forces with geometric relationship. To design a controller, a sliding mode control is adopted. Frequency domain analysis and simulation on vehicle simulation software, CarSim$^{(R)}$, show that the proposed method is effective for ride comfort.

• Coupled systems mechanics
• /
• 제2권1호
• /
• pp.111-126
• /
• 2013

The structural design requirements of an offshore platform subjected to wave induced forces and moments in the jacket can play a major role in the design of the offshore structures. For an economic and reliable design; good estimation of wave loadings are essential. A nonlinear response analysis of a fixed offshore platform under structural and wave loading is presented, the structure is discretized using the finite element method, wave plus current kinematics (velocity and acceleration fields) are generated using 5th order Stokes wave theory, the wave force acting on the member is calculated using Morison's equation. Hydrodynamic loading on horizontal and vertical tubular members and the dynamic response of fixed offshore structure together with the distribution of displacement, axial force and bending moment along the leg are investigated for regular and extreme conditions, where the structure should keep production capability in conditions of the 1-yr return period wave and must be able to survive the 100-yr return period storm conditions. The result of the study shows that the nonlinear response investigation is quite crucial for safe design and operation of offshore platform.