• 한국해양공학회지
• /
• 제13권4호통권35호
• /
• pp.82-97
• /
• 1999

A deep sea vehicle must be designed to ensure its safety under ultra-high pressure circumstances. If a pressure housing of a deepsea vehicle is collapsed by ultra-high pressure, the deepsea vehicle may be lost. The objective of this paper is to introduce a design collapse pressure for the deep sea pressure vessel which is composed of one cylinder and two hemispheres. Especially the collapse pressure of hemispherical shell with a hole at top is analyzed by a variational approach (weighted residual method). And for the purpose of design, the salty factor of collapse pressure is presented which is analyzed by interpolation method.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.2
• /
• pp.1109-1112
• /
• 2004

This study reports on the pressure relief design and braided composite of surge arrester. Surge arresters with porcelain housing must not have explosive breakage of the housing to minimize damage to other equipment when subjected to internal high short circuit current. As a solution, this study describes pressure relief design performance of arresters with braided composite module. In general, braided composite has Potential for improved impact and delamination resistance. Manufacturing processes of the braided composite could also be automated and could potentially lead to lower costs. Therefore, in consideration of characteristics of pressure relief for polymer arrester, the fabric pattern of braided composite was decided. And Polymer arrester module was manufactured with braid. The mechanisms of pressure occurrence and relief were investigated basically by analyzing arc energy and the correlation between thermal shock and indoor pressure in pressure relief test.

• 한국산학기술학회논문지
• /
• 제14권11호
• /
• pp.5330-5333
• /
• 2013

본 논문은 고압세척기의 성능을 향상시킨 제품개발을 위하여 현장에서 사용되는 고압세척기를 분해하여 측정하였으며 실제형상을 3차원 설계프로그램인 CATIA V5를 사용하여 모델링하였다. 또한 모델링된 고압세척기에 대하여 3차원 유한요소해석 프로그램인 ANSYS를 사용하여 유동해석을 수행하여 내부압력에 따른 유체의 흐름을 구하였다. 이러한 결과는 새로운 고압세척기의 제품개발에 활용될 예정이다.

• 대한기계학회논문집A
• /
• 제30권10호
• /
• pp.1328-1334
• /
• 2006

In the rolling mills for sheet metal rolling, paper rolling and etc., the impurities of roller surface have crucial effects on the surface quality of the products obtained by rolling. The Roll Cleaner is a device to remove impurities on roller surface during a rolling operation. Nip Pressure means the line pressure interacted between the roll cleaner blade and the roller surface. The nip pressure is the most important parameter which decides the performance of roll cleaner, and it depends upon several factors including the cleaner design and its blade stiffness. This study, first, analyzes the mechanism of the nip pressure generation for a roll cleaner designed commercially, which is an crucial process for effective design of roll cleaners. Second, the technique for the measurement of nip pressure is developed, which is useful to verify the performance of roll cleaners and to setup them properly at factory floor.

• 한국기계연구소 소보
• /
• 통권20호
• /
• pp.49-55
• /
• 1990

Filament-Wound composite pressure vessels offer significant weight saving over the conventional metal pressure vessels. S-2 glass/epoxy pressure vessel was designed, fabricated and tested. It was considered, in the analysis that the matrix and the metal liner of FRP pressure vessel shared the internal pressure. The thicknesses of hoop and helical layers were determinded by the computer program developed for the design of FRP/Metal structural pressure vessel. The computer program increased the structural efficiency about 14% comparing with the netting analysis. The experimental measurement on the deformation by internal pressure agrees with the theoretical analysis within the accuracy of 5%.

• 대한조선학회논문집
• /
• 제41권3호
• /
• pp.35-40
• /
• 2004

Since the scale of vessels is growing up recently, some troubles between the shaft and after bush bearing are frequently reported. Generally, mean pressure on bush bearing is used as a design criterion. However, in some case of the long bearing such as after bush bearing of the propulsion shaft, it might be liable to be locally under high pressure. As for the main engine bearings and the intermediate shaft bearing, it is reasonable to take the mean pressure as a design criterion. But, in case of after bush bearing, it is not sufficient because of the possibility of high pressure caused by local contact. In this study, Hertzian contact condition was applied to evaluation of the local pressure for after bush bearing. To reduce the local maximum pressure, the height of the after bush bearing was controlled. It was found that local maximum pressure could be reduced effectively by taking a partial slope on the white metal of the aft bush bearing.

• International journal of advanced smart convergence
• /
• 제6권4호
• /
• pp.1-8
• /
• 2017

In this work, the effects of fairly influential factors on performance of vacuum system, such as constant pressure and outgassing effect were simulated to propose the optimum design factors. Outgassing effects of selected vacuum materials on the vacuum characteristics were simulated by the $VacSim^{Multi}$ simulation tool. This investigation examined the feasibility of reliably simulating the outgassing characteristics of common vacuum chamber materials (aluminum, copper, stainless steel, nickel plated steel, Viton A). The optimum design factors for vacuum systems were suggested based on the simulation results. And, the effects of throttle valve applications on vacuum characteristics were also simulated to obtain the optimum design model of variable conductance on high vacuum system. Simulated vacuum characteristics of the proposed modelling were agreed with the observed experimental behaviour of real systems. Pressure limit valve and normally on-off control valve were schematized as the modelling of throttle valve for the constant process-pressure. Simulation results were plotted as pump-down curve of chamber and variable conductance of throttle valve. Simulated behaviors showed the applications of throttle valve sustained the process-pressure constantly, stably, and reliably.

• 소음진동
• /
• 제10권5호
• /
• pp.873-879
• /
• 2000

Experimental investigation was conducted to study the effects of pitch angle maximum camber on the performance and noise of an axial-flow fan used in outdoor-unit of air -conditioner. For this study the axial-flow fan whose pitch angle can be varied was made and the Specific sound Pressure Level and other coefficients were measured using the anechoic fan tester. It is found that pitch angle affects more severly than the maximum camber on the fan performance. On the while the maximum camber affects much on the specific sound power level. Present results show that it is important to choose the optimum pitch angle and maximum camber to design the high-performance and low-noise axial-flow fan and specific noise measured in the anechoic fan tester can be sued effectively for the design of low-noise fan.

• 기술발표회
• /
• 통권2006호
• /
• pp.311-319
• /
• 2006

Artesian Pressure exists in Hwa Jeon Project Site of Nakdong Delta Area. Maxium value of the pressure ranges between 06 tonf/m2 and 1 3 tonf/m2 in the design site. This paper presents a design case study considering the Artesian Pressure to calculate the consolidation settlement of the deep marine clay.

• Structural Engineering and Mechanics
• /
• 제56권5호
• /
• pp.745-765
• /
• 2015

This paper presents the design of reinforced concrete combined footings of trapezoidal form subjected to axial load and moments in two directions to each column using a new model to consider soil real pressure acting on the contact surface of the footing; such pressure is presented in terms of an axial load, moment around the axis "X" and moment around the axis "Y" to each column. The classical model considers an axial load and moment around the axis "X" (transverse axis) applied to each column, and when the moments in two directions are taken into account, the maximum pressure throughout the contact surface of the footing is considered the same. The main part of this research is that the proposed model considers soil real pressure and the classical model takes into account the maximum pressure, and also is considered uniform. We conclude that the proposed model is more suited to the real conditions and is more economical.