• Journal of Advanced Marine Engineering and Technology
• /
• v.23 no.3
• /
• pp.311-319
• /
• 1999

In Korea accelerated industry development and urbanization during the last three decades have led serious water pollution problems in many parts of the nation. Especially in the regions of west and south coast have low fresh water in the dry season of spring and summer. In the place isolated from land it is important to secure the fresh water for drinking and general service. This study is concerned on the thermal system design to develop low-pressure evaporation type fresh water gen-erator of capacity 1 ton/day using the heat source of non-operating boiler in the season of spring and summer. The results obtained from this study are as follows. the water quantitieds generated from experi-mental evaporator showed good coincidence with the calculated values. The maximum production quantity was 1.38ton/day at pressure 40mmHg abs. and temperature $80^{\circ}C$.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.3
• /
• pp.493-501
• /
• 2012

A rotational force generator for molten metal is developed using a linear motor design technology. Also, the developed device is applied to reproduce aluminum scraps and easy to control the rotate, stop, and forward and reverse rotation of molten metal. In addition, the developed device improves the melting speed and reproduction rate about 250 (%) and 96-99 (%), respectively, compared to the conventional handmade methods. Because it generates almost no dusts, it can improve working environments in a factory. Also, it has no losses in energy because it directly melts scraps. The device generates small amounts of the loss in refractory materials and aluminum caused by its oxidation because the molten metal is continuously rotated in which the loss and oxidized aluminum are the problems in the conventional melting and holding furnaces. Thus, it is possible to extend the life of furnaces and to produce high quality aluminum products.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.271-276
• /
• 2006

This paper shows the rotordynamic characteristics of a turbo-generator for a BOP of a fuel cell system. The rotor-bearing system consists of magnetic shaft and compressor-turbine shaft, and the two shafts are connected by spline coupling and supported by oil free air foil bearing. Preliminary design according to several parameter is considered in detail. Static and dynamic characteristics of the AFB are estimated by the soft elasto-hydrodynamic analysis technique and the perturbation method. The results of the natural frequencies, mode shape, and unbalance response analysis are presented.

• Proceedings of the KIEE Conference
• /
• 1997.07b
• /
• pp.488-490
• /
• 1997

This study is focused on the design and performance test of shaking table using stepping motor. Stepping motor can control the motion accurately with generated pulses and is applied to the shaking table. Earthquakes like El Centro and Taft are used as inputs to the shaking table. First, the number of pulses are calculated and sent to pulse generator. Then, the generator controls the table according to the pulse signs. It is shown that the measured signals from the table are in very good agreement with input signals of scale-downed earthquakes of El Centro and Taft. This table will be used for the experimental study of small-scaled building structures with tuned mass dampers under earthquakes.

• Proceedings of the IEEK Conference
• /
• 2002.07c
• /
• pp.1984-1987
• /
• 2002

This paper describes the design and implementation of a single-chip digitally synthesized 0-35MHz agile function generator. The chip comprises an integrated direct digital synthesizer (DDS) with a 10-bit on- chip digital-to-analog converter (DAC) using an n-well single-poly triple-metal 0.5-$\mu\textrm{m}$ CMOS technology. The main features of the chip include maximum clock frequency of 100 MHz at 3.3-V supply voltage, 32-bit frequency tuning word resolution, 12-bit phase tuning word resolution, and an on-chip 10-bit DAC. The chip provides sinusoidal, ramp, saw-tooth, and random waveforms with phase and frequency modulation, and power-down function. At 100-MHz clock frequency, the chip covers a bandwidth from dc to 35 MHz in 0.0233-Hz frequency steps with 190-ns frequency switching speed. The complete chip occupies 12-mm$^2$die area and dissipates 0.4 W at 100-MHz clock frequency.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.17 no.2
• /
• pp.132-141
• /
• 1992

The CCITT recommendation X.3, X.20, X.29 and X.25 protocols have been efficiently used in subscriber site for the purpose of using existing C DTE In the ISDN. The Packet Assem-bly /Disasembly (PAD) which covers these protocols can connect C_DTE to the PSDN. The number of C DTE connected to the PAI) Is dependent on the PAD performance. The design of the Traffic Generator (TG) S/W which can measure the PAD performance Is Introduced In this paper.

• Proceedings of the KIEE Conference
• /
• 1999.07a
• /
• pp.46-48
• /
• 1999

This paper treated the design and characteristics of high speed motor/generator with ring wound stator for the flywheel energy storage system. The most important advantages of the ring-wound motor is the slotless stator, i.e. no cogging torque, no space harmonic of air-gap flux density, etc. Because of these advantages, ring wound type motor is suitable to operate at the high speed.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.24 no.5
• /
• pp.887-895
• /
• 1987

This paper deals with the CMOS PLA Generator using CHISEL language. The program which plots a CMOS PLA alphanumeric layout automatically according to desired input functions and output functions has been developed. The program consists of procedures. These procedure are drawing a stick diagram with input data, converting any design rule, plotting a physical layout at IBM PC-AT with CIF input data. Physical layout information of dynamic CMOS PLA is stored CIF form. The CMOS PLA Generator is written in CHISEL which is layout language VLSI design tools and run on a VAX11/750 running UNIX.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 1999.04a
• /
• pp.186-195
• /
• 1999

This study is focused on the design and performance test of an earthquake simulator using stepping motor. Stepping motor which controls the motion accurately with generated pulses is applied to the earthquake simulator. Earthquakes like El Centro and Taft are used as inputs to the earthquake simulator. First the number of pulses are calculated and sent to pulse generator, . Then the generator controls the simulator according to the pulse sings, It is shown that the measured signals from the simulator are in very good agreement with input signals of scale-downed earthquakes of El Centro and Taft. This simulator will be used for the experimental study of small-scaled building structures with tuned mass dampers under earthquakes.

• Journal of the Korean Society of Safety
• /
• v.28 no.3
• /
• pp.6-10
• /
• 2013

The Heat Recovery Steam Generator(HRSG) is a device recycling the exhaust gas of gas turbine in combined power and chemical plants. Since service temperatures was very high, the damage of HRSG tubes intensively occurred in superheater and reheater. The aim of this paper is to determine life and hardness relationship that addresses creep-rupture test and creep-interrupt test in modified 9Cr-1Mo steel. The measured life that consists of function of hardness was found to constant tendency.