Effects of acid deposition on the acidification of surface water over a short term period were studied during June~October, 1995. A reservoir located in Chunchon, Kangwondo was selected for this study because this reservoir had received little man-made pollutants. Geological survey within the study area was carried out and the pH of a small and shallow stream flowing from the mountain valley down to the reservoir was monitored. Rainfall was measured by using a rain gauge and the precipitation was collected by automatic precipitation sampler. During the study period, rain pH was in the range of 3.81~5.77 with an average of 4.8. The EC was in the range of 5~189$\mu$S/cm with an average of 10.6$\mu$S/cm. ionic composition of the rainfall showed that of the anions, deposition of ${SO_4}^{2-}$, was highest with 3,119.7 kg/$\textrm{km}^2$, and it was $NH^{4+}$ with 1,053.2kg/$\textrm{km}^2$ for cations. The surface water pHs were maintained neutral or weak basic representing little evidence of acidification regardless of the acidic rainfall pH. Every time of sampling, however, the pHs exhibited increasing tendency as elevation of measuring site of the stream became lowered, which indicated the impacts of acid-base reactions by acidic or basic substances during travel of water downstream. This result suggested the necessity of further research to determine the respective buffering capacity of soil and underlying rocks.
This study was carried out to investigate the deposition aspect of acid precipitation in rural area of Chonbuk province by analysis of the chemical components in the precipitation at National Honam Agricultural Experiment Station, RDA in the suburbs of Iri from Jan. to Dec. in 1992. The results are summarized as follows: 1. The frequency of acid precipitation was 82.5% in 1992 and the month of the lowest frequency of 17% was June. 2. The pH range of the most precipitation amount was pH $4.5{\sim}5.0$ of 54.0% and the amount and ratio of the precipitation below pH 4.0 were 9.6 mm and 1.1%, respectively. 3. The seasonal acidity of precipitation was Summer(4.78)>Fall(4.59)>Spring(4.52)>Winter(4.16). 4. The components showed significant correlation with pH value were $SO_4^{2-}$ and $NO_3$ and the equivalence ratio between two components was 2.85 : 1. 5. The order of the major ion concentration in the precipitation was $SO_4^{2-}$>$NH_4^+$>$Cl^-$>$Ca^{2+}$>$NO_3^-$>$Na^+$>$H^+$>$K^+$>$Mg^{2+}$ and the equivalence ratio of total anion to cation was 1.20. 6. Deposition amount of nitrogen ($NO_3-N$ + $NH_4-N$) and potassium ($K_2O$) were 1.19 and 0.53 kg/l0a/year, respectively.
Kim, Ki Hyeok;Koo, Kee Young;Jung, UnHo;Roh, Hyeon Seog;Yoon, Wang Lai
한국신재생에너지학회:학술대회논문집
/
2011.05a
/
pp.157.1-157.1
/
2011
선택적 CO 산화반응(PrOx)에 사용되는 촉매 중 Pt, Ru, Rh 등의 귀금속 계 촉매들은 비귀금속 계 촉매에 비해 활성이 좋은 반면 가격이 비싸다는 경제적인 제한점이 있다. 따라서 소량의 귀금속을 사용하여 높은 활성의 촉매를 제조하고자 활성금속의 고분산 담지 방법에 대한 연구가 이루어지고 있다. 본 연구에서는 담체인 ${\gamma}-Al_2O_3$ 표면에 활성금속인 Pt의 고분산 담지를 위해 증착-침전법(Deposition-precipitation)을 적용하였으며 용액의 pH 변화에 따른 Pt 금속 입자의 분산도에 대한 영향을 살펴보았다. Pt의 함량은 1wt%로 고정하였고 침전제로 NaOH를 사용하여 용액의 pH를 pH 7.5 ~ 10.5로 변화시켰다. 제조된 촉매는 세척 후 $400^{\circ}C$, 3시간 소성 하였다. 제조된 1wt% Pt/$Al_2O_3$ 촉매의 특성분석을 위해 BET, TPR, CO-chemisorption을 수행하였다. PrOx 반응 실험은 GHSV=60,000 $ml/g_{cat}{\cdot}h$, $T=100{\sim}200^{\circ}C$, ${\lambda}$=4 조건에서 수행되었으며 반응 전에 촉매는 $400^{\circ}C$, 3시간 환원 후 사용하였다. 촉매의 특성분석과 PrOx 반응 실험 결과를 통해 촉매가 담체 위에 고분산 되는 최적의 pH를 확인할 수 있었으며, 기존의 함침법으로 제조된 촉매와 성능 비교를 통해 제조방법에 따른 영향을 살펴보았다.
To look into the degree of the long distance movement of the air pollution within Mt. Kyebang, Hongcheon, one of the clean regions, major ions, components of collected wet precipitation, were analyzed by using the ion chromatography after measuring pH and electrical conductivity. The quality assurance of chemical composition data was checked by considering the ion balance and electrical conductivity. Also, the pH of precipitation showed in the pH5.0~5.5 range, less than the pH5.6 in which the standards of the acid precipitation. On the whole, the more precipitation got, the less ion concentration became.: It could showed what it influenced on the fluctuation of the precipitation pH according to fluctuation and neutralization of the according materials. In the meantime, as composition ratios of wet deposition, ${SO_4}^{2-}$ and $nss-{SO_4}^{2-}$, ${NH_4}^+$ and $nss-Ca^{2+}$ accounted for high percentage. Especially, as the concentration of ${SO_4}^{2-}$, the artificial pollutant, and $Ca^{2+}$, the soil substance, showed high, Mt. Kyebang, Hongcheon having barely fixed air-pollutants sources was most likely to be influenced by the pollutants moved from long distances.
Proceedings of the Korean Vacuum Society Conference
/
2014.02a
/
pp.283.2-283.2
/
2014
열필라멘트 화학증착공정(Hot Wire Chemical Vapor Deposition)에서 기상 에서 생성되는 하전된 실리콘 나노입자와 저온결정성 실리콘박막 증착의 연관성을 압력의 변화에 따른 상호비교를 통해 조사하였다. 필라멘트 온도는 $1800^{\circ}C$로 고정시키고 0.3~2 torr의 범위에서 공정 압력을 변화시키면서 증착하였다. 압력이 증가함에 따라 증착된 실리콘 박막의 결정화도는 증가하였으며, 증착속도는 감소하였다. 반응기 압력에 따른 기상에서 생성되는 나노입자의 크기분포의 변화를 조사하기 위하여 탄소막이 코팅된 투과전자현미경(Transmission Electron Microscopy) 그리드 위에 실리콘 나노입자를 포획하고 관찰하였다. 포획된 실리콘 나노입자의 크기분포와 개수농도는 압력이 증가함에 따라 감소하였다. 투과전자현미경을 이용하여 분석한 결과, 나노입자는 결정성 구조를 보였다. 압력이 증가함에 따라 나노입자의 크기가 감소하고 개수농도가 감소하는 것은 증착속도의 감소와 관련됨을 알 수 있다. 한편, 공정압력 증가에 따른 나노입자의 크기분포 및 개수농도 감소와 증착속도의 감소는 일반적으로 알려진 기상에서 석출하는 고상의 평형석출량(equilibrium amount of precipitation)이 압력의 증가함에 따라 증가한다는 사실과 일치하지 않는다. 이러한 압력경향성은 Si-H 시스템이 0.3~2 torr의 압력 영역에서 retrograde solubility를 갖는 것을 의미한다. 나노입자의 하전여부, 크기분포 및 개수농도를 측정하기 위하여 입자빔질량분석장비(Particle Beam Mass Spectroscopy)를 이용하였다. 그 결과, 실리콘 나노입자는 양 또는 음의 극성을 가진 하전된 상태임을 확인하였고, 투과전자현미경(TEM) grid에 포획한 실리콘 나노입자의 크기와 경향성이 일치하였다. 이는 나노입자가 저온의 기판에서 핵생성되어 성장하여 생성된 것이 아니라 열필라멘트 주위의 고온영역에서 생성된 것을 의미한다.
An organometallic precursor, hfac(hexafluoroacetylacetonate) Cu(I) DMB (3,3-dimethyl- 1-butene) was synthesized, evaluated and compared with other precursors for metal organic chemical vapor deposition of copper thin films. It was found that at $40^{\circ}C$, the vapor pressure was an order of magnitude higher (about 3 torr) than (hfac) Cu vinyltrimethylsilane (VTMS) and films could be deposited at the substrate temperature of 100-$280^{\circ}C$ with deposition rate substantially higher. The copper films contained no detectable impurities as measured by Auger electron spectroscopy and had a resistivity of about 2.0$\mu\Omega$-cm in the deposition temperature range of 150 to $250^{\circ}C$. From the thermal analysis, (hfac)Cu(I)(DMB) is believed to be quite stable and no appreciable amount of precipitation was observed at $65^{\circ}C$ heating for more than a month.
The concentrations and wet deposition flux into the sea of heavy metals of precipitation in Pusan area were measured and estimated. The samples were collected by polyethylene bottle(30ι) from January to November in 1996, and heavy metals were analyzed by atomic absorption spectrometer. The concentration order of heavy metals was Al >Fe >Zn >Pb >Mn >Cu >Ni >Cd >Co, and they were high at inland sites and low at coastal sites. The enrichment factors for some metals(Zn, Cu, Pb, Cd), based on crustal Al, were significantly greater than unity, and the order was Cd > Pb > Zn > Cu. This evidence suggests Cd and Pb are derived predominantly from non-crustal sources. Al, Fe and Mn contents showed good correlation with each other. Therefore this enrichment factor indicates similar geochemical behavior of these elements. The annual wet depositional flux(mg/ $m^2$ /yr) from Pl site was as follows: Al(121.1). Fe,(177.2), Zn(12.9), Mn(6.19), Pb(14.4), Cu(0.64), Ni(1.03), Cd(1.02) and Co(1.01).
Journal of the Korean institute of surface engineering
/
v.44
no.6
/
pp.246-249
/
2011
Surface modification before coating nickel by coupling agents and/or etchant of glass did not provide enough adhesive strength of electroless nickel deposits on glass. Effect of heat treatments on hardness as well as adhesion of nickel deposits was studied by using tape test for adhesion, nanoindenter for hardness and glancing angle x-ray diffractometer (GAXRD) for phase characterization. Heat treatment improved hardness as well as adhesion. XRD results give that the improvements of adhesion and hardness are due to the formation of $NiSiO_4$ around the interface between the nickel deposits and the glass and the precipitation of $Ni_3P$ causing precipitation hardening, respectively. The details in effects of heat treatment on adhesion and hardness are described here.
Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
/
2002.07b
/
pp.935-938
/
2002
The degree of contamination in outdoor insulation system is one of the most importance factor to determine the level of insulation, and the salt is known as the most dangerous contaminants in the most region of the world. In a macroscopic point of view, as shown through the preceding study, the generation and deposition of salt contaminants has a great relation with the geographical conditions and the meteorological conditions, such as, wind velocity, wind direction, precipitation and so forth. However, in the aspect of microscopic analysis, the pollution mechanism has a great relation with aerodynamic properties of insulator, originated from the profile of insulators, and the non-uniform deposition is unevitable. So, in this investigation, we had make a experiment to seize the electrical properties of non-uniformly contaminated insulator. The results of this investigation could be used as a good groundwork in the determination of outdoor insulation design.
Biomimetic apatite formation and deposition behaviors of Ti-6Al-7Nb and Ti-6Al-4V plates in simulated body fluids(SBF) under various conditions were examined. In case of regular samples without collagen treatments the weight gain due to apatite precipitation on the surface in Ti-6Al-4V was found to be higher than in Ti-6Al-7Nb. In case of collagen-coated samples, the weight gain in Ti-6Al-4V continued to be higher than in Ti-6Al-7Nb, but the difference between the two became smaller. Both Ti-6Al-7Nb and Ti-6Al-4V samples with collagen coating exhibited an appreciable increase of weight gain, which may be caused by the interaction between collagen and $Ca^{+2}$ ions. The weight gain was found to be not much affected by the addition of collagen to SBF. The ill-defined granular structure in the presence of collagen can be associated with the increasing volume fraction of amorphous calcium phosphate.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.