• Journal of Society of Preventive Korean Medicine
• /
• v.5 no.2
• /
• pp.40-68
• /
• 2001

In this study, grade of subjective symptom appealed by laborer of Jeollabuk-do was evaluated using questionary regarding factor made effect on musculoskeletal disease and in addition, studied relationship with health promotion life style of them. Based on the result, relationship of general characteristics of musculoskeletal subjective symptom and life-style of the subjects was concluded as below. 1. General characteristics of study subjects were as following. Ratio of male was higher as 57.7% of male and 42.2% female and age distribution was 5.1% of 20s, 34.99% of 30s, 36.3% of 40s and 23.7% of 50s and therefore, $30{\sim}40$ aged groups showed highest ratio. Most subjects (74.9%) was married status and in case of education level, high-school graduate and dropout (23.3%) and over-college graduate (46.8%) showed highest distribution. $1{\sim}2$ Mil. KRW (29.5%) and $2{\sim}2.99$ Mil. KRW (21.2%) is the main income distribution and however there was high ratio of non-reply (29.0%). In case of employment period, $10{\sim}14$ years (15.3%) and over 15 years (29.6%) showed highest ratio and there were many non-reply (39.4%) and in addition, 67.6% replied as own house and 14.3% as lease on deposit base in question of residence type. 2. Subjects showed high ratio of subjective symptom appeal of 62.79% and many cases (50.23%) appealed 1 or 2 symptoms. Symptom by body region was 29.8% (waist), 27% (shoulder), 21.2% (knee), 15.5% (neck), 9.5% (ankle), 8.1% (wrist) and 5.0% (elbow) in order. In case of relationship with general characteristics, female comparing with male, non-residence of own house, subjects with lower education level and employment period of $10{\sim}14$ years showed higher appeal rate and kind of symptoms than others. Therefore, it was concluded that rate of musculoskeletal symptom appeal have close relationship with gender, level of living, education level, age and employment period. 3. In case of severe pain of upper body except waist and ankle, it was appealed in both or right side and it means that upper body pain is originated from right side and right region pain is transited to both region pain. In addition, there was 39.41% of non-reply to existence of right-left region pain and therefore, it was evaluated that, in may cases, there was no awareness of their own symptom condition even on subjective symptom. 4. Degree of pain was, as pain over middle level, evaluated as 2.79 on full mark of 4.0 and in order of waist (2.97), ankle (2.83), knee (2.82), wrist (2.82), neck (2.79), shoulder (2.70) and elbow (2.62). In addition, 71.97% appealed $2{\sim}3$ cases for the latest 1 week. Owing to subjective symptom, 54.95% drop into hospital or pharmacy, 10.32% made temporary retirement or absence, 7.99% transferred into more comfortable duty and $39.4{\sim}54%$ experienced one or more managing mentioned above. 5. Fulfillment of health promotion life style of subjects was evaluated on full mark of 4.0 and total score was 2.63. Average mark of each area was personal relationship (3.05), self-realization (2.92), stress management (2.63), health control (2.48), physical exercise (2.19) and nutrition management (2.19) and personal relationship was highest and physical exercise and nutrition management were lowest. As general characteristics influencing health promotion life style, gender, residence style and employment period showed significant difference. Male showed higher mark than female and showed higher mark in order of own house, others, lease on deposit base, monthly rent. Subjects with longer employment period showed higher mark with significant difference. 6. Accounting of factor influencing each area of health promotion life style, self-realization showed significance in marriage status, income, residence style and education level and health control in age, residence style and employment period. Physical exercise showed significant difference in gender, age, residence style and employment period and nutrition in gender, age, residence style and employment period. Stress management showed significant difference in residence style and employment period and however not in personal relationship. 7. Health promotion life style relating with existence and kind of pain showed significant difference in all area except personal relationship area. In absence of pain, there was statistically significant high score in all area even in total health promotion life style and all area. Accounting of kind of pain, cases of $1{\sim}2$ kinds of pain and $5{\sim}6$ kinds of pain showed relatively high score and it was lower than mark of subject stated absence of pain. 8. Subjects appeal symptom were classified by symptom region and difference of total and each areas were evaluated. General area (p=0.002), self-realization (p=0.012), health management (p=0.023), physical exercise (p=0.028), nutrition management (p=0.028) and stress control (p=0.001) showed statistically significant difference and not in personal relationship area. Especially, elbow, shoulder and neck area marked high and group appealed pain of knee, arm and elbow, foot and ankle marked low. Based on those results, subjective symptom should be accounted seriously in diagnosis of occupational musculoskeletal disease of laborer and among subjective symptom, general characteristics of gender, age, condition of living, education level and employment period make effect. Generally subject appeal symptom marked lower than subject without symptom appeal and it means that life management of subject appealing musculoskeletal pain make important role in management and treatment of occupational musculoskeletal disease.

• Journal of the Korean Electrochemical Society
• /
• v.13 no.4
• /
• pp.270-276
• /
• 2010

Nickel-copper foam electrodes with pore gradient micro framework and nano-ramified wall have been prepared by using an electrochemical deposition process. Growth habit of nickel-copper co-deposits was quite different from that of pure nickel deposit. In particular, the ramified structure of the individual particles was getting clear with chloride ion content in the electrolyte. The ratio of nickel to copper in the deposits decreased with the distance away from the substrate and the more chloride ions in the electrolyte led to the more nickel content throughout the deposits. Compositional analysis for the cross section of a ramified branch, together with tactical selective copper etching, proved that the copper content increased with approaching central region of the cross section. Such a composition gradient actually disappeared after heat treatment. It is anticipated that the pore gradient nickel-copper nanostructured foams presented in this work might be a promising option for the high-performance electrode in functional electrochemical devices.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.52-52
• /
• 2009

To date, chalcogenide alloy such as $Ge_2Sb_2Te_5$(GST) have not only been rigorously studied for use in Phase Change Random Access Memory(PRAM) applications, but also temperature gap to make different states is not enough to apply to device between amorphous and crystalline state. In this study, we have investigated a new system of phase change media based on the In-Sb-Te(IST) ternary alloys for PRAM. IST chalcogenide thin films were prepared in trench structure (aspect ratio 5:1 of length=500nm, width=100nm) using Tri methyl Indium $(In(CH_3)_4$), $Sb(iPr)_3$ $(Sb(C_3H_7)_3)$ and $Te(iPr)_2(Te(C_3H_7)_2)$ precursors. MOCVD process is very powerful system to deposit in ultra integrated device like 100nm scaled trench structure. And IST materials for PRAM can be grown at low deposition temperature below $200^{\circ}C$ in comparison with GST materials. Although Melting temperature of 1ST materials was $\sim 630^{\circ}C$ like GST, Crystalline temperature of them was ~$290^{\circ}C$; one of GST were $130^{\circ}C$. In-Sb-Te materials will be good candidate materials for PRAM applications. And MOCVD system is powerful for applying ultra scale integration cell.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.36 no.4
• /
• pp.695-704
• /
• 2016

Rubber deposited during aircraft landing is known as the main cause of reducing surface friction force on wet surfaces. Thus, rubber deposits are removed at regular intervals for sae airplane landing. The high-pressure waterblast method, widely used for the removal of rubber deposits, is regarded as the main cause for the loss of surface material because in this method, water hits the surface directly at a high pressure. In this study, a rubber removal primer is developed to reduce surface damage by lowering the pressure of waterblast relatively during the removal of rubber deposits such that the deposits are removed efficiently even with a lower water pressure. To achieve this, basic materials appropriate for the primer were selected and their performance, penetration rate, and site applicability were evaluated. Based on the evaluations, the proportion of additive required for improving the performance of the basic materials was first determined. Then, the optimum mix ratio was derived through the evaluation of the effect on pavements, and the development of the rubber removal primer was completed.

• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.860-863
• /
• 1992

In this paper, we investigate $\pi$-A isotherms of biological lipid layer such as cholesterol and phosphatidyl choline to study a gas sensor characteristics which response only to specific materials. And, we also deposit it on the surface of quartz crystal by vertical dipping method and horizontal lifting method. Then, we evaluate the deposition status of cholesterol and phosphatidyl choline LB film using AT-cut quartz crystal. We obtain the following results: (1) Cholesterol's solid surface pressure is about 20$\sim$40(dyne/cm) and limiting area is about 50${\AA}^2$/molecule. And, phosphatidyl choline's surface pressure is about 25$\sim$40(dyne/cm) and limiting area is about 20 ${\AA}^2$/molecule. (2) When LB films are deposited, the deposition ratio is coincident with the frequency shift. Therefore, we can evaluate the deposition status of LB film. (3) For cholesterol, Y type LB films are deposited up to 15 layers by vertical dipping method. (4) For phosphatidyl choline, X typo LB films are deposited to 15 layers by horizontal lifting method. But, in case of vertical dipping method, the deposition status is not good.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.13 no.1
• /
• pp.47-56
• /
• 2010

The main objectives of this comparative study were 1) to quantify the potential contribution of wood chips to revegetation on the cut slope in a constructed area, 2) to compare the floristic similarity of species composition whether existing of wood chips in the soil media or not. Wood chips were combined with soil media in the ratio of 30%. The thin layer (1 cm, 3 cm) soil media revegetation methods and the thick layer (10 cm) soil media revegetation method were constructed on the cut slopes by machineries respectively. Also, comparative experiments the existence of wood chips in the soil media were conducted to evaluate the effects of wood chips on revegetation works. The total size of quadrat was $300m^2$ ($100m^2{\times}3$). The results of monitoring for 3 years on cut slopes were as follows: 1) All the quadrat existed in the proper range for vegetation. 2) Species richness of quadrat including wood chips was 10% more than those of commercial soil medias. 3) The coverage rates of quadrat including wood chips were similar or superior to those of conventional methods. It can be concluded that the use of wood chips would be effective to promote establishment of diverse landscape and vegetation. However, it behooves to continue monitoring on succession of vegetation for ecological restoration. Finally, adequate wood chips deposit and gathering methods should be studied properly.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.208-208
• /
• 2010

Indium zinc tin oxide (IZTO) thin films were studied as a possible alternative to indium tin oxide (ITO) films for providing low-cost transparent conducting oxide (TCO) for thin film photovoltaic devices. IZTO films were deposited onto glass substrates at room temperature. A dc/rf magnetron co-sputtering system equipped with a ceramic target of the same composition was used to deposit TCO films. Earlier studies showed that the resistivity value of $In_{0.6}Zn_{0.2}Sn_{0.2}O_{1.5}$ (IZTO20) films could be lowered to approximately $6{\times}10^{-4}ohm{\cdot}cm$ without sacrificing optical transparency and still maintaining amorphous structure through the optimization of process variables. The growth rate was kept at about 8 nm/min while the oxygen-to-argon pressure ratio varied from 0% to 7.5%. As-deposited films were always amorphous and showed strong oxygen pressure dependence of electrical resistivity and electron concentration values. Influence of forming gas anneal (FGA) at medium temperatures was also studied and proven effective in improving electrical properties. In this study, the chemical composition of the targets and the films varied around the $In_{0.6}Zn_{0.2}Sn_{0.2}O_{1.5}$ (IZTO20). It was the main objective of this paper to investigate how off-stoichiometry affected TCO characteristics including electrical resistivity and optical transmission. In addition to the composition effect, we have also studied how film properties changed with processing variables. IZTO thin films have shown their potential as a possible alternative to ITO thin films, in such way that they could be adopted in some applications where currently ITO and IZO thin films are being used. Our experimental results are compared to those obtained for commercial ITO thin films from solar cell application view point.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.44-44
• /
• 2008

GdBCO coated conductor have been fabricated using reactive co-evaporation. The batch type co-deposition system was specially designed and was named EDDC (evaporation using drum in dual chamber) that is possible to deposit superconducting layer with optimum composition ratio of materials at temperature over $700^{\circ}C$ and several mTorr of oxygen. The IBAD-MgO substrate with the architecture of LaMnO3(LMO)/IBAD-MgO/Hastelloy was used for coated conductor. In this study, GdBCO superconducting layer was deposited on IBAD-MgO substrate at optimal oxygen partial pressure (pO2) and deposition temperature. After fabrication of GdBCO coated conductor, critical current density was measured by 4-probe method. Surface morphology and texture of GdBCO coated conductors were analyzed by the SEM and XRD, respectively.

• 한국해양학회지
• /
• v.29 no.4
• /
• pp.357-365
• /
• 1994

The sediments on the continental shelf off the west coast (middle part) of Korea are divided into northern sandy deposits and southern muddy sediments, respectively. The sandy sediments consist dominantly of quartz and feldspar grains, representing mature-stage sediment in composition. Further-more, the presence of iron-stained quartz grain and glauconite does indicate that the sediments are similar to the relict sediments on the outer shelf of Yellow Sea and East China Sea. These sandy sediments are interpreted as a basal sands that were deposited during the transgression period due to sea-level rise after to last glacial maximum (LGM). The tidal deposits in the Namyang Bay, the west coast of Korea are divided vertically into the upper layer of muddy sediments and the lower layer of sandy sediments. the upper layer sediments contain abundant rock fragments, and are interpreted as the modern tetragenous sediments. The lower layer sediments, on the other hand, are rich in quartz and feldspar grains, representing high index of sediment maturity ratio. the lower layer sandy deposits show the presence of iron-stained.

• Fisheries and Aquatic Sciences
• /
• v.13 no.2
• /
• pp.140-149
• /
• 2010

We determined the seasonal gonad maturation in Strongylocentrotus nudus sea urchins inhabiting an artificially enhanced seaweed forest along the Samchuk Coast of Korea from April 2006 to March 2007. A total of 30 sea urchins per month were collected from the study area, and gonadosomatic index (GSI), gonad index (GI), egg diameter, and RNA/DNA variation were measured for each specimen. GSI values of female and male urchins achieved maximums of 17.6 and 17.0, respectively, in June. Based on histological studies, maximum GI values occurred in July (4.6 for females and 4.8 for males). A mean ovarian egg diameter of $73.7\;\pm\;14.2\;{\mu}m$ was measured in August; during the main spawning period in September, mean egg diameter reached a maximum of $74.2\;\pm\;17.8\;{\mu}m$. The RNA/DNA ratio and RNA content for both males and females showed a distinct peak during the ripe stage in July, but another peak occurred in the spring season from March to April, when urchins deposit protein into the nutritive phagocytes of immature gonads prior to gametogenesis. The reproductive cycle of S. nudus is divided into five stages: early active (December-May), late active (March-July), ripe (July-September), spent and degenerative (August-November), and inactive (October-February). Our continuous removal of sea urchins from the study area did not influence the reproductive cycle, as populations quickly recovered, and achieved normal gonad development cycle in the site.