• Nuclear Engineering and Technology
• /
• v.45 no.2
• /
• pp.211-218
• /
• 2013

Large quantities of irradiated graphite waste from graphite-moderated nuclear reactors exist and are expected to increase in the case of High Temperature Reactor (HTR) deployment [1,2]. This situation indicates the need for a graphite waste management strategy. Of greatest concern for long-term disposal of irradiated graphite is carbon-14 ($^{14}C$), with a half-life of 5730 years. Fachinger et al. [2] have demonstrated that thermal treatment of irradiated graphite removes a significant fraction of the $^{14}C$, which tends to be concentrated on the graphite surface. During thermal treatment, graphite surface carbon atoms interact with naturally adsorbed oxygen complexes to create $CO_x$ gases, i.e. "gasify" graphite. The effectiveness of this process is highly dependent on the availability of adsorbed oxygen compounds. The quantity and form of adsorbed oxygen complexes in pre- and post-irradiated graphite were studied using Time of Flight Secondary Ion Mass Spectrometry (ToF-SIMS) and Xray Photoelectron Spectroscopy (XPS) in an effort to better understand the gasification process and to apply that understanding to process optimization. Adsorbed oxygen fragments were detected on both irradiated and unirradiated graphite; however, carbon-oxygen bonds were identified only on the irradiated material. This difference is likely due to a large number of carbon active sites associated with the higher lattice disorder resulting from irradiation. Results of XPS analysis also indicated the potential bonding structures of the oxygen fragments removed during surface impingement. Ester- and carboxyl-like structures were predominant among the identified oxygen-containing fragments. The indicated structures are consistent with those characterized by Fanning and Vannice [3] and later incorporated into an oxidation kinetics model by El-Genk and Tournier [4]. Based on the predicted desorption mechanisms of carbon oxides from the identified compounds, it is expected that a majority of the graphite should gasify as carbon monoxide (CO) rather than carbon dioxide ($CO_2$). Therefore, to optimize the efficiency of thermal treatment the graphite should be heated to temperatures above the surface decomposition temperature increasing the evolution of CO [4].

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.3
• /
• pp.451-458
• /
• 2015

The deployment density of AP increases as well as the density WLAN stations due to increase of WLAN use and the real performance of WLAN is degraded. To improve the performance, there are many PHY/MAC technologies and OFDMA and full duplex are promising technologies among them. In conventional OFDMA WLAN MAC relate works, there are some limitations in terms of channel utilization and collision probability. Thus, it need to research for effective channel allocation protocol. Full duplex can transmit data on the same time and same frequency resource so it can allocate channel more flexible than half duplex. In this paper, we prose the OFDMA FD-MAC(Full Duplex MAC) protocol that it allocates the sub-channels based on the idle channel information for full duplex pair. In addition, it shows the throughput improvement by performance analysis.

• KIPS Transactions on Computer and Communication Systems
• /
• v.9 no.9
• /
• pp.197-206
• /
• 2020

Collaborative research in science applications based on HPC service needs rapid transfers of massive data between research colleagues over wide area network. With regard to this requirement, researches on enhancing data transfer performance between major superfacilities in the U.S. have been conducted recently. In this paper, we deploy multiple data transfer nodes(DTNs) over high-speed science networks in order to move rapidly large amounts of data in the parallel filesystem of KISTI's Nurion supercomputer, and perform transfer experiments between endpoints with approximately 130ms round trip time. We have shown the results of transfer throughput in different size file sets and compared them. In addition, it has been confirmed that the DTN cluster with three nodes can provide about 1.8 and 2.7 times higher transfer throughput than a single node in two types of concurrency and parallelism settings.

• Science of Emotion and Sensibility
• /
• v.7 no.2
• /
• pp.107-121
• /
• 2004

Although consumer needs for better products force manufactures to put emphasis on design, often development of a product has been done without the formal phase to consider human needs. In order to identify the implicit needs of customers and the areas of potential demand on a product, several analysis scheme such as QFD(quality function deployment) has been developed. For this, first of all, the methods for evaluating consumers satisfaction about their needs must be determined. However there were only few systematic methods on shoe design. In this paper we developed an innovative framework for human satisfaction evaluation of shoes. As a result, we uncovered 29 dominant human satisfaction dimensions for customer-oriented quality evaluation of a comfortable shoes. Here, 29 satisfaction dimensions were identified as the dimensions that represent the human sensitivity and psychological feeling on comfortable shoes. This study helped the designers and developers clarify the conceptual and abstract aspect of the design evaluation by proposing a more systematic and process-oriented method.

• Journal of KIISE:Information Networking
• /
• v.30 no.1
• /
• pp.117-125
• /
• 2003

IPv6 (IP version 6), which was standardized by the IETF (Internet Engineering Task Force) to cope with existing IPv4 problems, needs several approaches for interoperation with IPv4. The internetworking of IPv6 with IPv4 is an important key to the deployment of the next generation Internet. As the solutions to the transition mechanism, both tunneling and translator methods have been proposed. In this paper, we analyze functional elements for implementation design of a transition mechanism based on the NAT-PT (NAT-Protocol Translation), and propose an extension algorithm that uses ports for effective use of global IPv4 addresses. The algorithm presented in this paper is a method of combining NAT-PT with Port Translation mechanism. The algorithm does not assign an IPv4 address to the host that needs IPv4 address, but allocates a single temporary IPv4 address and a port number in order to identify host.

• Journal of KIISE:Information Networking
• /
• v.37 no.5
• /
• pp.386-395
• /
• 2010

Widespread deployment of infrastructure WLANs has made Wi-Fi an integral part of today's Internet access technology. Despite its crucial role in affecting end-to-end performance, past research has focused on MAC protocol enhancement, analysis, and simulation-based performance evaluation without sufficiently considering a misbehavior stemming from capture effect. It is well known that the capture effect occurs frequently in wireless environment and incurs throughput unfairness between nodes. In this paper, we propose a novel Fair MAC algorithm which achieves fairness even under physically unfair environment. While satisfying the fairness, the proposed algorithm maximizes the system throughput. Extensive simulation results show that the proposed Fair MAC algorithm substantially improves fairness without throughput reduction.

• 한국가시화정보학회:학술대회논문집
• /
• 2006.12a
• /
• pp.17-20
• /
• 2006

Passenger safety is fundamental factor in automobile. Among much equipment for passenger safety, the air bag system is the most fundamental and effective device. Beside of the front air bag system which installed on most of all automobiles, a curtain-type air bag is increasingly adapted in deluxe cars fur protecting passengers from the danger of side clash. Curtain type airbag system consists of inflator housing, fill hose, curtain airbag. Inflator housing is a main part of the curtain-type air bag system for supplying high-pressure gases to deploy the air bag-curtain. Fill hose is a passageway to carry the gases from inflator housing to each part of curtain airbag. Therefore, it is very important to design the vent holes of fill hose for good performance of airbag deployment. But, the flow information from vent holes of fill hose is very limited. In this study, we measured instantaneous velocity fields of a high-speed flow ejecting from the vent holes of fill hose using a dynamic PIV system. From the velocity Held data measured at a high frame-rate, we evaluated the variation of the mass flow rate with time. From the instantaneous velocity fields of flow ejecting from the vent holes in the initial stage, we can see a flow pattern of wavy motion and fluctuation. The flow ejecting from the vent holes was found to have very high velocity fluctuations and the maximum velocity was about 480m/s at 4-vent hole region. From the mass flow rate with time, the accumulated flow of 4-vent hole has occupied about 70% of total flow rate.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.2
• /
• pp.149-156
• /
• 2014

Floor number determination has attracted considerable attention because many applications require accurate floor number information for providing better localization services in multistory buildings. This paper describes a Wi-Fi-based, low-complexity floor number determination method for multistory buildings. In our scheme, with the exception of floor ID and received signal strength of each WAP, detailed information on the wireless access point (WAP) coordinates is not needed. The multi-wall-floor model is used for the simulation and analysis. The simulation results show that the floor determination accuracy is nearly 100 given an adequate deployment density of WAPs on each floor. The results also show that the proposed method provides a good estimate of floor number even when only a few WAPs are implemented on each floor. Specifically, the proposed method can work under extreme conditions, i.e., where there are no WAPs on a floor.

• Journal of Internet Computing and Services
• /
• v.15 no.2
• /
• pp.129-142
• /
• 2014

Latest in Smart Grid projects are emerging as the biggest issue that smart meter should meet the security goal and the SW upgrade for compliance with future standard. However, unlike regular equipment, Smart meters should be designed in accordance with the regulation of legal metrology instrument in order to establish a fair trade-based business and unauthorized changes, it is not allowed and it is strictly limited by law. Therefore, this paper propose a new scheme of certification regarding type approval and verification for legal smart meter as analyzing the requirements of a smart meter regarding upgrade and security. This analysis shows that the proposed scheme comply with the regulation and the specification of smart meter by applying it to smart meter with smart card.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.12 no.2
• /
• pp.254-259
• /
• 2008

Mesh WLANs, which consist of wireless mesh routers connecting each other in a mesh topology and self-operate after their autoconfiguration, have several advantages in convenience, swiftness and flexibility of deployment and operation over existing WLANs the expansions of which are done by connecting the APs with wires. However, many technical issues still remain to be solved. Among them, network performance degradations due to the interference between the adjacent hops in multi-hop mesh WLANs, and the reusability of the existing wireless network protocols are critical problems to be answered. This work evaluates the VoIP support performance of IEEE 802.11a/g-based mesh WLANs with multiple wireless interfaces with simulations. The results show that there exit an unfairness in VoIP packet delay performances among mobile routers located at different hops, and that although the capacity of the admitted calls can be increased by increasing the size of voice packet payload it is far less than the expected one. This suggests that the existing 802.11 MAC protocols have their limitation when applied in mesh networks and their enhancement or even a newer one nay be required.