• Smart Structures and Systems
• /
• 제29권3호
• /
• pp.387-393
• /
• 2022

This paper presents the vibration analysis of cracked ceramic-reinforced aluminum composite beams by using a method based on changes in modal strain energy. The crack is considered to be straight. The effective properties of composite materials of the beams are estimated through Mori-Tanaka micromechanical model. Comparison study and numerical simulations with various parameters; ceramic volume fraction, reinforcement aspect ratio, ratio of the reinforcement Young's modulus to the matrix Young's modulus and ratio of the reinforcement density to the matrix density are taken into investigation. Results demonstrate the pronounced effects of these parameters on intact and cracked ceramic aluminum beams.

• Steel and Composite Structures
• /
• 제52권5호
• /
• pp.583-593
• /
• 2024

The present paper deals with the dynamic analysis of cracked ceramic-reinforced aluminum composite fixed beams by using a method based on changes in modal strain energy. Mechanical characteristics of composite materials of the beams are predicted through Mori-Tanaka micromechanical scheme. A Comparative study and numerical simulations involve various parameters; ceramic volume fraction, reinforcement aspect ratio, ratio of the reinforcement Young's modulus to the matrix Young's modulus and ratio of the reinforcement density to the matrix density are taken into investigation. The obtained results prove the important effects of these parameters on intact and cracked ceramic aluminum beams.

• 한국농공학회지
• /
• 제33권4호
• /
• pp.84-95
• /
• 1991

The compaction ratio of the field dry density to the maximum dry density is generally adopted as the index of quality control for embankment of earthfill structures such as Earth Dam, Sea Dike, River Bank and Road. In case of coarse materials are included in the earth material, the compaction ratio will be varied in wide range since the dry density is influenced by quantity of coarse material in the soil. The treatment for the coarse material should be controlled carefully in testing. In this study, the compaction characteristics of the soil contained the coarse materials were researched and calibration of the suitability of field quality control methods were carried out. 28 Samples were made of clay(CL) and sandy soil (SM) mixed with gravel whose content were 0, 4, 6, 8, 10, 12, 15, 20, 25, 30, 35, 40, 45, and 60% in Weight. The compaction characteristics depending on the coarse material content were analysed through 4 types of compaction tests which are A-1, B-i, C-i and D-1. The adjusting coefficients for density and moisture content namely a and ${\beta}$ respectively were proposed in order to consider the effects depending on content of the coarse materials. The test methods to control reasonably and promptly the quality of earthfill were proposed after analysing the ranges of possible errors on the relative compaction ratio between laboratory compaction methods and field density testing methods.

• Asian-Australasian Journal of Animal Sciences
• /
• 제21권2호
• /
• pp.262-269
• /
• 2008

The aim of this study was to determine the effects of breeder age and stocking density on performance, carcass characteristics and some stress parameters (H-L ratio, serum glucose, cholesterol and triglyceride levels, tonic immobility test (TI), antibody production, relative asymmetry (RA) and external appearances). This experiment was carried out with 705 one-day old male broiler chicks (Ross 308) obtained from three different ages of broiler breeder (32, 48 and 61 wks). Each age group was randomly divided into two stocking density groups (11.9 and 17.5 broilers per $m^2$) with 5 replications per group. The experimental period was 6 weeks. Broilers from 32 wk-old breeders had lower initial weight (p<0.001), body weight gain of the first 3 week of rearing (p<0.01), the percentage of abdominal fat (p<0.001) and serum cholesterol level (p<0.01); higher percentage of gizzard (p<0.01) and longer TI duration (p<0.001) than those from 48 and 61 wk-old breeders. Broilers reared at 17.5 b/m2 had lower final BW, body weight gain, feed consumption, feather condition and foot health (p<0.001), higher percentage of heart, H-L ratio, serum glucose and cholesterol levels (p<0.001), and longer TI durations (p<0.001). There were no significant interactions in examined parameters except for feed to gain ratio between breeder age and stocking density.

• 한국분말재료학회지
• /
• 제22권2호
• /
• pp.111-115
• /
• 2015

This study investigates the microstructure and thermal shock properties of polycrystalline diamond compact (PDC) produced by the high-temperature, high-pressure (HPHT) process. The diamond used for the investigation features a $12{\sim}22{\mu}m$- and $8{\sim}16{\mu}m$-sized main particles, and $1{\sim}2{\mu}m$-sized filler particles. The filler particle ratio is adjusted up to 5~31% to produce a mixed particle, and then the tap density is measured. The measurement finds that as the filler particle ratio increases, the tap density value continuously increases, but at 23% or greater, it reduces by a small margin. The mixed particle described above undergoes an HPHT sintering process. Observation of PDC microstructures reveals that the filler particle ratio with high tap density value increases direct bonding among diamond particles, Co distribution becomes even, and the Co and W fraction also decreases. The produced PDC undergoes thermal shock tests with two temperature conditions of 820 and 830, and the results reveals that PDC with smaller filler particle ratio and low tap density value easily produces cracks, while PDC with high tap density value that contributes in increased direct bonding along with the higher diamond content results in improved thermal shock properties.

• 상하수도학회지
• /
• 제23권5호
• /
• pp.669-678
• /
• 2009

The reduction of excess activated sludge from petrochemical plant was investigated by the electro fenton (E-Fenton) process using electrogenerated hydroxyl radicals which lead to mineralization of activated sludge to $CO_2$, water and inorganic ions. Factors affecting the disintegration efficiency of excess activated sludge in E-Fenton process were examined in terms of five criteria: pH, $H_2O_2/Fe^{2+}$ molar ratio, current density, initial MLSS (mixed liquid suspended solids) concentration, $H_2O_2$ feeding mode. TSS total suspended solid and $TCOD_{cr}$ reduction rate increased with the increasing $H_2O_2/Fe^{2+}$ molar ratio and current density until 42 and $6.7 mA/cm^2$, respectively but further increase of $H_2O_2/Fe^{2+}$ molar ratio and current density would reduce the reduction rate. On the other hand, as expected, increasing pH and initial MLSS concentration of activated sludge decreas TSS and $TCOD_{cr}$ reduction rate. The E-Fenton process was gradually increased during first 30 minutes and then linearly proceed till 120 minutes. The optimal E-Fenton condition showed TSS reduction rate of 62~63% and $TCOD_{cr}$ (total chemical oxygen demand) reduction rate of 55~56%. Molar ratio $H_2O_2/Fe^{2+} = 42$ was determined as optimal E-Fenton condition with initial $Fe^{2+}$ dose of 5.4 mM and current density of $6.7{\sim}13.3 mA/cm^2$, initial MLSS of 7,600 mg/L and pH 2 were chosen as the most efficient E-Fenton condition.

• 한국멀티미디어학회논문지
• /
• 제16권9호
• /
• pp.1077-1088
• /
• 2013

브로드캐스팅은 한 노드가 모든 노드들에게 패킷을 전달하는 과정으로, 모바일 애드 혹 네트워크(MANET)에서 경로 탐색과 제어 정보 메시지 전송과 같은 서비스를 위하여 많이 사용되는 기본 작업이다. 본 논문에서는 MANET에서 송수신 노드 사이의 이격 비율과 노드 밀집도에 따라 동적으로 재전송 확률 값을 구하는 브로드캐스팅 기법을 제안한다. 이격 비율은 송수신 노드사이의 거리와 무선 전파의 전달 거리에 대한 비율을 계산하며, 노드 밀집도는 1-홉 단위의 이웃 노드의 수를 계산한다. 패킷을 수신한 노드는 송신노드로부터의 이격 비율과 자신의 노드 밀집도을 고려하여 재전송 확률을 결정하는데, 송신자에 가까운 노드와 노드 밀집도가 높은 노드는 낮은 재전송 확률 값을 부여하여 패킷의 조기 소멸을 통해 재전송 패킷의 수를 줄이도록 한다. 플러딩 기법과 고정된 확률 값 기법과의 성능 비교를 통하여 제안 기법이 다른 방법보다 우수한 성능을 보여주었는데, 제안 기법은 플러딩에 비하여 30% 이상의 패킷 전송을 감소시킬 수 있었으며, 96%에 가까운 패킷의 도착율을 보여주었다.

• 한국기계가공학회지
• /
• 제20권8호
• /
• pp.42-51
• /
• 2021

Investigations of process parameters are essential when fabricating high-quality parts using additive manufacturing. This study investigates the change in the mechanical characteristics of a SUS316L specimen fabricated using selective laser melting based on the energy density and bead overlap ratio. The SUS316L powder particles were spherical and 35 ㎛ in size. Single-bead and hexahedral shape deposition experiments were performed sequentially. A single bead experiment was performed to obtain the bead overlap ratios for different laser parameters utilizing laser power and scan speed as experimental parameters. A hexahedral shape deposition experiment was also performed to observe the difference in mechanical properties, such as the internal porosity, surface roughness, and hardness, based on the energy density and bead overlap ratio of the three-dimensional printed part. Laser power, scan speed, overlap ratio, and layer thickness were chosen as parameters for the hexahedral shape deposition experiment. Accordingly, the energy density applied for three-dimensional printing, and the experimental parameters were calculated, and the energy density and bead overlap ratio for fabricating parts with good properties have been suggested.

• 한국응용곤충학회지
• /
• 제42권3호
• /
• pp.233-240
• /
• 2003

항온$.$항습 조건에서 Amblyseius fallacis의 접종밀도별 귤응애에 대한 밀도억제효과를 조사한 결과, 16 : 1(Panonychus citri :A.fallacis) 이상의 비율로 접종한 경우에 귤응애의 밀도가 매우 효과적으로 억제되었다. 그리고 귤응애의 초기 밀도가 잎 당 0.5마리와 1마리일 때 20:1로 1-2회씩 방사한 결과, 모든 처리에서 A.fallacis의 밀도는 다소 높게 형성되었으나 귤응애에 대한 뚜렷한 억제효과를 보이지는 않았다. 정상적으로 관리되고 있는 비닐하우스의 감귤나무에서 귤응애가 잎 당 0.1-0.2마리 정도일 때 10:1로 2회 방사한 경우에는 A.fallacis의 밀도도 높게 형성되었으며, 유기합성농약을 살포한 처리구와 동일할 정도의 높은 방제효과를 보였다. 그리고 이리응애가 서식하는 곳은 수관 내부이므로 수관 내부와 외부의 환경차이를 조사한 결과,주간에는 수관내부가 외부에 비해 기온은 낮고, 상대습도는 높기 때문에 A.fallacis의 서식에 다소 유리한 것으로 나타났으며, 기온은 7.2$^{\circ}C$ 이상, 상대습도는 18.5% 이상까지도 차이가 있었다.

• 한국농촌건축학회논문집
• /
• 제19권1호
• /
• pp.35-42
• /
• 2017

This study aims to investigate the change in building density and residential environment after the reconstruction of decrepit public rental housing complexes formed in accordance with the Land Readjustment Project during the 1970s-80s. The results of this study can be summarized as follows: First, in terms of change in residential environment after the reconstruction, floor plans that were limited to two to four types and to small apartments measuring $42.9m^2$(13py)-$56.1m^2$ (17py) became varied, presenting 5-6 types of floor plans and various sizes of apartments. In particular, the reconstructed apartments were mainly built in a size smaller than 85($m^2$) and in the 3LDK floor plan and staircase-style unit architectural structure in order to reflect the lifestyle of residents. Second, in terms of change in building density after the reconstruction, the building coverage ratio did not change a lot, but the floor area ratio showed great change depending on the complex, ranging from a minimum of 2.9 times (Singdong Complex) to a maximum of 5.4 times (Eoyangdong Complex). Such change is attributable to the reconstruction policy that aims to improve the residential environment for original residents, secure economic feasibility and efficiency, and reflect the lifestyle of residents while incorporating dividends assigned to the existing housing project members as well as the maximum floor area ratio allowed by the regulation. Additionally, in terms of change in the number of floors and building density after the reconstruction, the former 5-story apartments were changed to apartments with 16-28 stories. Accordingly, the number of households in each complex has also increased by 20%. Third, according to the characteristics of parking facilities in terms of the size and density of parking spaces, former apartment complexes had only aboveground parking lots, not underground parking area. The newly constructed apartment complexes have underground parking space, and the parking-housing ratio is 1.1-1.3 cars.