• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.4
• /
• pp.1437-1448
• /
• 1996

This paper presents a simplified model for approximate analysis of the solute redistribution in coarsening dendrite arms during solidification of binary metal alloys. By introducing a quadratic concentration profile with a time-dependent coefficient, the integral equation for diffusion in the solid phase is reduced to a simple differential relation between the coefficient and the solid-liquid interface position. The solid fraction corresponding to the system temperature is readily determined from the relation, phase equilibrium and the overall solute balance in which the liquid phase is assumed to be completely mixed. In order to validate the developed model, calculations are performed for the directional solidification of Al-4.9 mass Cu alloy. The predicted eutectic fractions for a wide range of the cooling rate reasonably agree with data from the well-known experiment as well as sophisticated numerical analyses. Also, the results for the back diffusion limits are consistent with available references. Additional calculations show that the characteristic parameters such as the coarsening, density variation and nonlinarity in the phase diagram significantly affect the microsegregation. Owing to the simplicity, efficiency and compatibility, the present model may be suitable for the micro-macroscopic solidification model as a microscopic component.

• Journal of Powder Materials
• /
• v.3 no.1
• /
• pp.25-32
• /
• 1996

Flying and solidification behaviors of the particles manufactured by centrifugal atomization were investigated. Both models were solved by the explicit FDM. Flying calculation supported the experimental results that the finer particles flied shorter than coarser particles and that particles flied shorter for lower rotation velocity than for higher velocity. Cooling curve and dendrite arm spacing were predicted by use of heat transfer analysis.

• Applied Microscopy
• /
• v.23 no.1
• /
• pp.15-24
• /
• 1993

The toxic effects of methylmercury on the ultrastructures of the brain and gill tissues of fightingfish and compensative effects of red ginseng were investigated by means of electron microscopy. The brain neuron of methylmercury exposure group showed dilatation of dendrite and axon, numerical decrease of ribosomes, partial loss of nucleoplasm and cytoplasm and considerable swelling of mitochondria as compared with the normal neuron. And necrotic cell with ruptured nucleus and vacuolated mitochondria was noticeable. While, slight swelling of mitochondria, some dilation of dendrite and axon and numerical increase of ribosome occurred in the neuron of methylmercury-red ginseng treatment group as compared with the methylmercury exposure group. In the gill lamella of methylmercury exposure group, collapse of pillar cells and arms, dilated epithelial cell and thickened membrane were observed. While, in the gill lamella of methylmercury-red ginseng treatment group, arms were slightly disintegrated and basement membrane was some thickend as compared with the methylmercury exposure group. From the above results, it is concluded that red ginseng has detoxication effect on methylmercury toxicity and so takes compensative effect on injured tissues caused by methylmercury intoxication.

• Corrosion Science and Technology
• /
• v.16 no.2
• /
• pp.49-58
• /
• 2017

Many research efforts on the effect of nitrogen on the corrosion resistance of stainless steels have been reported, but little research has been conducted on the effect of nitrogen for the weldment of stainless steels by the seal-weld method. Therefore, this work focused on the determining the corrosion resistance of tube/tube sheet mock-up specimen for sea water condensers, and elucidating the effect of shielding nitrogen gas on its resistance. The pitting corrosion of autogenously welded specimen propagated preferentially along the dendritic structure. Regardless of the percent of shielding nitrogen gas, the analyzed nitrogen contents were very much lower than that of the bulk specimen. This can be arisen because the nitrogen in shielding gas may partly dissolve into the weldment, but simultaneously during the welding process, nitrogen in the alloy may escape into the atmosphere. However, the pitting resistance equivalent number (PREN) of the interdendrite area was higher than that of the dendrite arm, regardless of the shielding gas percent; and the PREN of the interdendrite area was higher than that of the base metal; the PREN of the dendrite arm was lower than that of the base metal because of the formation of (Cr, Mo) rich phases by welding.

• Journal of Korea Foundry Society
• /
• v.42 no.2
• /
• pp.77-82
• /
• 2022

Initial solidification condition during directional solidification of superalloy CM247LC was controlled with various cooling methods such as insertion of alumina disc or Ni foil or inoculant, and direct pouring of melt onto chill plate. Rapid cooling with direct pouring of melt onto chill plate resulted in generation of many fine grains and precipitation of fine γ' particles, as well as small dendrite arm spacing. Tensile properties of directionally solidified superalloy CM247LC were closely related to microstructure which was governed by initial solidification conditions. Directionally solidified CM247LC with small dendrite arm spacing and fine precipitates showed good tensile properties.

• Journal of Korea Foundry Society
• /
• v.10 no.3
• /
• pp.219-224
• /
• 1990

In this, we have investigated the solute behavior in front of solid-liquid interface according to the change of the cooling rate in bronze alloy and phosphor bronze alloy. The conclusive summary is as follows: 1) The secondary dendrite arm spacing was decreased with increasing the cooling rate. 2) The minimum solute concentration happened to along centerline of primary arm, and the maximum solute concentration was found at the boundary of arm or between the arms the minimum solute concentration was increased with the cooling rate. 3) Segregation Index S was decreased with increasing the cooling rate and content of P. 4) The degree of the microsegregation was decreased with increasing the cooling rate. The effective distribution coefficient, Ke was increased with addition of P in Cu-Sn.

• Korean Journal of Materials Research
• /
• v.24 no.10
• /
• pp.538-542
• /
• 2014

Microstructural and mechanical characteristics of Al-6Si-2Cu alloy for lightweight automotive parts were investigated. The test specimens were prepared by gravity casting process. Solution heat treatments were applied to as-cast alloys to improve mechanical properties. The microstructure of the gravity casting specimen presents a typical dendrite structure, having a secondary dendrite arm spacing (SDAS) of $37{\mu}m$. In addition to the Al matrix, a large amount of coarsened eutectic Si, $Al_2Cu$ intermetallic phase, and Fe-rich phases were identified. After solution heat treatment, single-step solution heat treatments were found to considerably improve the spheroidization of the eutectic Si phase. Two-step solution treatments gave rise to a much improved spheroidization. The mechanical properties of the two-step solution heat treated alloy have been shown to lead to higher values of properties such as tensile strength and microhardness. Consequentially, the microstructural and mechanical characteristics of Al alloy have been successfully characterized and are available for use with other basic data for the development of lightweight automotive parts.

• Korean Journal of Materials Research
• /
• v.14 no.6
• /
• pp.425-431
• /
• 2004

A laser welding was applied between sintered tip of Fe-Co-W and low carbon steel shank for the diamond saw blade. The welding characteristics and formation of defects were investigated carefully for the weld fusion zone in different welding condition. Dendrite arm spacing in weld bead decreased with decrease of heat input. Co and W increased and Fe decreased in the weld fusion zone with increase of the heat input. The corresponding change of composition was observed with the change of beam position. The maximum and total length of crack decreased with increase of the heat input. The crack in weld bead was propagated along the dendrite boundary and was caused mainly by the segregation of constituent during the solidification.

• Journal of the Korean Society for Heat Treatment
• /
• v.13 no.4
• /
• pp.246-252
• /
• 2000

Stellite 12 alloy-powder was overlaid on 410 stainless steel valve seat using plasma transferred arc(PTA) process. Variation of characteristic of microstructure and hardness of deposit with current(90~150 A) and preheat temperature(R.T.~$400^{\circ}C$) was investigated. Important conclusion obtained are as follows; All welding conditions used produced a sound deposit layer with no defect in single pass welding. The maximum deposit had 4.0~4.8 mm in thickness and its bead width was increased with increase of current and preheat temperature. The deposit showed hypoeutectic microstruture, which was consisting of primary cobalt dendrite and networked $M_7C_3$ type eutectic carbides. The amount of eutectic carbides was decreased and its dendritic secondary arm spacing was increased with increase of current. Hardness of the deposit was decreased with increase of current. Preheat temperature up to $400^{\circ}C$, however, showed little influence on the hardness and microstructure. The hardness was also influenced by diluted Fe content near the interface in addition to microstructure and dendritic secondary arm spacing. Hot hardness at $500^{\circ}C$ showed higher than 300 HV.

• Journal of Korea Foundry Society
• /
• v.14 no.6
• /
• pp.566-575
• /
• 1994

The effects of varying the pouring temperature and the die preheating temperature in producing centrifugally cast HP alloy modified with Nb was evaluated on the basis of the resultant macrostructure, microstructure and hardness of these castings. Increased die preheating temperatures and pouring temperatures resulted in an increase in the thickness of the columnar dendritic zone, the primary and secondary dendrite arm spacing and the thickness of the zone of porosity at the casting I.D.(inner diameter). Lower die preheating temperature and pouring temperatures result in increased grain fineness and an increased zone of equiaxed grains. A higher hardness was achieved toward the casting O.D.(outer diameter) compared to the casting I.D., attributable to alloy segregation toward the casting I.D. and segregation differences resulting from reduced solidification cooling rates toward the casting I.D. Also, a higher hardness was realized at the cold end of the casting attributed to a more uniform distribution of carbides.