• Proceedings of the Korean Institute of Communication Sciences Conference
• /
• 2004.11a
• /
• pp.239-239
• /
• 2004

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.27 no.5
• /
• pp.808-815
• /
• 1990

This paper treats with the design method for the single loop oversampled Sigma-Delta A/D converter with one delay and the digital integrator. Such an integrator was kgenerated by means of the bilinear transform of the analog integrator. The frequency spectrums of the quantizer and the decimator output signal are evaluated by FFT respectively. With the performance evaluation system, the values of SNR are obtained versus the input sinusoidal signal amplitude, frequency, the oversampling ratio, the DC-input level, the loop gain and the limitting value of the integrator. As compared with existing results, values of SNR versus the input signal amplitude and the oversampling ratio for the suggested system are about 6dB higher then previously reported results respectively. Furthermore, this approach achieves an about 60dB input dynamic range.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.11
• /
• pp.141-148
• /
• 2012

A design of a 32-bit fourth-stage decimation filter decimation filter used in sigma-delta analog-to-digital (A/D) converter is proposed in this work. A four-stage decimation filter with down-sampling factor of 512 and 32-bit output is developed. A multi-stage cascaded integrator-comb (CIC) filter, which reduces the sampling rate by 64, is used in the first stage. Three half-band FIR filters are used after the CIC filter, each of which reduces the sampling rate by two. The pipeline structure is applied in the CIC filter to reduce the power consumption of the CIC. The Canonic Signed Digit (CSD) arithmetic is used to optimize the multiplier structure of the FIR filter. This filter is implemented based on a semi-custom design flow and a 130nm CMOS standard cell library. This decimation filter operates at 98.304 MHz and provides 32-bit output data at an audio frequency of 192 kHz with power consumption of $697{\mu}W$. In comparison to the previous work, this design shows a higher performance in resolution, operation frequency and decimation factor with lower power consumption and small logic utilization.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.10
• /
• pp.148-158
• /
• 2012

This paper presents the design of the incremental delta-sigma ADC. The proposed circuit consists of pre-amplifier, S & H circuit, MUX, delta-sigma modulator, and decimation filter. Third-order discrete-time delta-sigma modulator with 1-bit quantization were fabricated by a $0.18{\mu}m$ CMOS technology. The designed circuit show that the modulator achieves 87.8 dB signal-to-noise and distortion ratio (SNDR) over a 5 kHz signal bandwidth and differential nonlinearity (DNL) of ${\pm}0.25$ LSB, integral nonlinearity (INL) of ${\pm}0.2$ LSB. Power consumption of delta-sigma modulator is $941.6{\mu}W$. It was decided that N cycles are 200 clock for 16-bits output.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.15 no.3
• /
• pp.342-348
• /
• 2015

This paper presents a 1.9-GHz digital ${{\Delta}{\Sigma}}$ fractional-N PLL with a finite impulse response (FIR) filter embedded for noise suppression. The proposed digital implementation of FIR provides a simple method of increasing the number of taps without complicated calculation for gain matching. This work demonstrates 32 tap FIR filtering for the first time and successfully filtered the in-band phase noise generated from delta-sigma modulator (DSM). Design considerations are also addressed to find the optimum number of taps when the resolution of time-to-digital converter (TDC) is given. The PLL, fabricated in $0.11-{\mu}m$ CMOS, achieves a well-regulated in-band phase noise of less than -100 dBc/Hz for the entire range inside the bandwidth of 3 MHz. Compared with the conventional dual-modulus division, the proposed PLL shows an overall noise suppression of about 15dB both at in-band and out-of-band region.

• Journal of IKEEE
• /
• v.17 no.4
• /
• pp.511-516
• /
• 2013

This paper presents a SDM using the FDPA technique. The FDPA technique is the added feedback path which is the delayed path of DAC output. The designed SDM increases the SNR by adding the delayed digital feedback path. The proposed SDM is easily implemented by eliminating the analog feedback path. Through the MATLAB modeling, the optimized coefficients are obtained to design the SDM. The designed SDM has a power consumption of $220{\mu}W$ and SNR(signal to noise ratio) of 81dB at the signal-bandwidth of 20KHz and sampling frequency of 2.56MHz. The SDM is designed using the $0.18{\mu}m$ standard CMOS process.

• Proceedings of the KIEE Conference
• /
• 1998.07g
• /
• pp.2411-2413
• /
• 1998

In this paper, using tile concept of block digital filtering, and the design procedure of time-interleaved oversampling converter are presented. it is shown that arbitrary sigma-delta A/D converter can be converted into corresponding time-interleaved structure. The TIM structure of this paper is designed by the bilinear transform. To verify the simulation results, a second-order TIM structure A/D converter has been implemented and the design process as well as experimented results are presented.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.15 no.5
• /
• pp.335-342
• /
• 2022

In this paper, a single-bit 3rd-order feedforward delta sigma modulator is proposed for audio applications. The proposed modulator is based on a class-C inverter for low voltage and power applications. For the high-precision requirement, the class-C inverter with regulated cascode structure increases its DC gain and acts as a low-voltage subthreshold amplifier. The proposed Class-C inverter-based modulator is designed and simulated in 180-nm CMOS process. With no performance loss and a low supply voltage compatibility, the proposed class-C inverter-based switched-capacitor modulator achieves high power efficiency. This design achieves an signal-to-noise-and-distortion ratio (SNDR) of 93.9 dB, an signal-to-noise ratio (SNR) of 108 dB, an spurious-free dynamic range (SFDR) of 102 dB, and a dynamic range (DR) of 102 dB at a signal bandwidth of 20 kHz and a sampling frequency of 4 MHz, while only using 280 μW of power consumption from a 0.8-V power supply.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.13 no.3
• /
• pp.184-196
• /
• 2020

In this paper, a single-bit 2nd-order delta-sigma modulator with the architecture of cascaded-of-integrator feedforward (CIFF) is proposed for precision measurement of current flowing through a secondary cell battery in a battery management system (BMS). The proposed modulator implements two switched capacitor integrators and a single-bit comparator with peripheral circuits such as a non-overlapping clock generator and a bias circuit. The proposed structure is designed to be applied to low-side current sensing method with low common mode input voltage. Using the low-side current measurement method has the advantage of reducing the burden on the circuit design. In addition, the ±30mV input voltage is resolved by the ADC with 15-bit resolution, eliminating the need for an additional programmable gain amplifier (PGA). The proposed a single-bit 2nd-order delta-sigma modulator has been implemented in a 350-nm CMOS process. It achieves 95.46-dB signal-to-noise-and-distortion ratio (SNDR), 96.01-dB spurious-free dynamic range (SFDR), and 15.56-bit effective-number-of-bits (ENOB) with an oversampling ratio (OSR) of 400 for 5-kHz bandwidth. The area and power consumption of the delta-sigma modulator are 670×490 ㎛2 and 414 ㎼, respectively.

• Proceedings of the KIEE Conference
• /
• 2003.11b
• /
• pp.75-78
• /
• 2003

In this paper, a second-order 3-bit DSM using DWA(Data Weighted Averaging) algorithm is designed for bluetooth Zero-IF Receiver. The designed circuit has two integrators using a designed OTA, nonoverlapping two-phase clerk generator, 3-bit A/D converter, DWA algorithm and 3-bit D/A converter An ideal model of second-order lowpass DSM with a 3-bit quantizer was configured by using MATLAB, and each coefficients and design specification of each blocks were determined to have 10-bit resolution in 1MHz channel bandwidth. The designed second-order 3-blt lowpass DSM has maximum SNR of 74dB and power consumption is 50mW at 3.3V.