• Journal of the Korean Institute of Gas
• /
• v.19 no.5
• /
• pp.54-60
• /
• 2015

The autoignition temperature (AIT) of a material is the lowest temperature at which the material will spontaneously ignite. The AIT is important index for the safe handling of flammable liquids which constitute the solvent mixtures. This study measured the AITs of n-decane+ethylbenzene system by using ASTM E659 apparatus. The AITs of n-decane and ethylbenzene which constituted binary system were $210^{\circ}C$ and $430^{\circ}C$, respectively. The experimental AITs of n-decane+ethylbenzene mixture were a good agreement with the calculated AITs by the proposed equations with about $11^{\circ}C$ A.A.D.(average absolute deviation).

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.2
• /
• pp.305-311
• /
• 2010

iATA (Internet Advanced Technology Attachment) is a block-level protocol developed to transfer ATA commands over TCP/IP network, as an alternative network storage solution to address insufficient storage problem in mobile devices. This paper employs RAID5 distributed storage servers concept into iATA, in which the idea behind is to combine several machines with relatively inexpensive disk drives into a server array that works as a single virtual storage device, thus increasing the reliability and speed of operations. In the case of one machine failed, the server array will not destroy immediately but able to function in a degradation mode. Meanwhile, information can be easily recovered by using boolean exclusive OR (XOR) logical function with the bit information on the remaining machines. We perform I/O measurement and benchmark tool result indicates that additional fault tolerance feature does not delay read/write operations with reasonable file size ranged in 4KB-2MB, yet higher data integrity objective is achieved.

• Korean Journal of Community Nutrition
• /
• v.5 no.2
• /
• pp.185-192
• /
• 2000

As the percentage of the elderly in the population increases, research to identify the nutritional and health status of the elderly, to understand the factors influencing on them, and to delay aging have been done actively. It is necessary for these studies to be longitudinal. This study was carried out to assess the change of health-related habits such as dietary behaviors and smoking, alcohol drinking and exercising habit, and health status between previous study(1991/1994) and post study(1998) for middle-aged men and women living in Chonju. For the present study, the data of 63 pairs(23 men and 40 women) were analyzed. They were 11 men and 12 women followed up from 82 men and 100 women surveyed in 1994. Mean ages in the 1991/4 and 1998 studies were 53.6y(range 42-63y) and 59.0y(range 46-72y) respectively. The survey was conducted with interview using a questionnaire including dietary behaviors and health-related habits, and anthropometric measurement and blood test for analyzing biochemical indices in 1991/4 and 1998. To understand these changes over time, $\chi$$^2$-statistics, t-test and paired t-test were analyzed with an SAS package program. As people age, there were significantly decreases in the proportions to eat lightly salted foods and drink alcohol. Significant longitudinal increases in triceps skin fold thickness, ${\gamma}$-GPT and HDL-cholesterol and significant decrease in hemoglobin value were noted over time in both men and women. In addition a significant decrease in blood glucose level was noted over time in women. Weight, blood glucose and total cholesterol increased significantly with age in those had had breakfast regularly or those had not used more slat at the table in the past. From this study, were found out the subjects of this study had relatively desirable health-related habits. But as improper health-related habits are likely to result in inappropriate health status(eg, increase in WHR, triglyceride, total cholesterol and LDL-cholesterol), it is recommended that nutrition education in necessary as soon as possible to meet the health elderly.

• Korean Journal of Geomatics
• /
• v.2 no.1
• /
• pp.57-64
• /
• 2002

Measuring the depth of water is very important in ensuring the protection and safety of seaside. There are many difficulties in making the contour bathymetric map, and contour line due to the limitation of continuous measurement of water depth and collimation with the conventional measuring and positioning methods. But the real-time kinematic GPS (RTK GPS) positioning using a carrier phase enables us to decide a precise position without breaking a signal even under the condition of a moving environment. It is also possible to obtain an accurate depth of water in real time with a fathometer through the measuring of time delay between sending and receiving epochs. This research aims at investigation of accuracy potential of RTK GPS in combination with Echo Sounder(E/S) for the coastal mapping. Apart from this purpose, the accuracy of ambiguity resolution with the OTF(On the Fly) method was tested with respect to the initialization time. The result shows that the accuracy is better than 1cm with 5-minute initialization in the distance of 10km baseline. The seaside topography was measured by the RTK GPS only, on the other hand the seafloor topography was surveyed in combination of RTK GPS and E/S. Comparing to the volume of seaside measured by RTK GPS and digital topographical map, the difference of only 2 % was achieved. This indicates that the coastal mapping with RTK GPS is successfully conducted. In addition it is also demonstrated that the 3-dimensional perspective model resulted from the undersea topography measured by RTK GPS and E/S is very close to that from the digital map. Through this study, it was verified that RTK GPS is to be very useful method in the analysis of coastal morphology owing to its capability of getting the precise DTM for the using of harbor reclamation, dredging, and the estimation of soil movement in a river.

• KIPS Transactions on Computer and Communication Systems
• /
• v.10 no.2
• /
• pp.53-58
• /
• 2021

In this paper, an alternative finite memory structure(FMS) smoothing filter is developed for discrete-time state-space model with a control input. To obtain the FMS smoothing filter, unbiasedness will be required beforehand in addition to a performance criteria of minimum variance. The FMS smoothing filter is obtained by directly solving an optimization problem with the unbiasedness constraint using only finite measurements and inputs on the most recent window. The proposed FMS smoothing filter is shown to have intrinsic good properties such as deadbeat and time-invariance. In addition, the proposed FMS smoothing filter is shown to be equivalent to existing FMS filters according to the delay length between the measurement and the availability of its estimate. Finally, to verify intrinsic robustness of the proposed FMS smoothing filter, computer simulations are performed for a temporary model uncertainty. Simulation results show that the proposed FMS smoothing filter can be better than the standard FMS filter and Kalman filter.

• Journal of the Korean Geotechnical Society
• /
• v.26 no.7
• /
• pp.171-186
• /
• 2010

It is generally known that the mechanism of behavior in the flexible earth retaining system is relatively more complicated than in the rigid earth retaining system. Moreover in the case of long span strut supporting system the analysis of strut axial force change becomes more difficult when the differences of ground condition and excavation work progress on both sides of excavation section are added. When deeper excavation than the specification or installation delay of supporting system or change of ground condition happen during construction process, lots of axial force can be induced in some struts, which threaten the safety of construction. This paper introduces two examples of long span deep excavation where struts and rock bolts were used as a supporting system with flexible wall structure. The characteristics of ground deformation and strut axial force change, which were measured in the sections of two examples that are 50 meters apart in one construction site and have almost similar design and construction conditions were analysed, the similarity and difference between measurement results of two examples were compared and investigated. This article aims to improve and develop the technique of design and construction in future projects having similar ground condition and supporting method.

• Journal of the Korean Society of Safety
• /
• v.38 no.5
• /
• pp.1-7
• /
• 2023

This study analyzes the operational characteristics of 311 aged and non-aged residual current circuit breakers (RCCBs) in low-voltage consumer contexts. It investigates the influence of external temperature and harmonics based on the rated current multiples. To simulate temperature variations, a convectional oven was used around the circuit breakers. Additionally, the generation of harmonic reference signals and data measurement for overcurrent experiments were conducted using NI SCXI, myDAQ, and LabVIEW. An observation revealed that as the ambient temperature increased, the operating time of RCCBs decreased in the time delay region. This was attributed to the faster response or bending of the bimetal, which is the tripping element. However, aged RCCBs encountered challenges with tripping outside the protective curve. The operating time of the circuit breakers exhibited an acceleration influenced by the order and content of harmonic currents, potentially leading to malfunctions. Aged RCCBs demonstrated faster operating times than their non-aged counterparts. However, the difference in operating time varied based on the manufacturer's and operating environment of the RCCBs. Frequent malfunctions of RCCBs can result in power outages. In cases where these circuit breakers fail to operate, they can lead to secondary damages, including electrical fires and shocks. Consequently, it is imperative to consider the operating environment of RCCBs and provide appropriate replacement cycles to mitigate these risks.

• Advances in materials Research
• /
• v.13 no.3
• /
• pp.233-241
• /
• 2024

Quantitative analysis of the Zingiber Officinale sample using subcritical water extraction (SWE) was developed employing High-Performance Liquid Chromatography (HPLC) to bolster the advancement of this innovative green extraction process. This research focuses on three principal ginger bioactive compounds: 6-gingerol, 6-shagoal, and 10-gingerol. Various stages were undertaken to establish the quantitative analysis method, encompassing the optimisation of HPLC operating conditions and the formulation of standard calibration curves, yielding individual compound equations. A robust correlation within the calibration curve was achieved, exhibiting an r² value of 0.9814 and an RSD of 5.00%. A simultaneous, swift, and dependable method was established with an injection time of 20 minutes and an 8-minute delay between injections, in contrast to the previous HPLC analysis requiring a 45-minute injection time for detecting and quantifying all components. Notably, no post-treatment was applied after the SWE process. This advancement allows for potential future online measurement of Zingiber Officinale bioactive compounds extracted using subcritical water extraction through this technology.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.36 no.5
• /
• pp.370-376
• /
• 2016

Corrosion on the surface of a structure can generate cracks or cause walls to thin. This can lead to fracturing, which can eventually lead to fatalities and property loss. In an effort to prevent this, laser imaging technology has been used over the last ten years to detect thin-plate structure, or relatively thin piping. The most common laser imaging was used to develop a new technology for inspecting and imaging a desired area in order to scan various structures for thin-plate structure and thin piping. However, this method builds images by measuring waves reflected from defects, and subsequently has a considerable time delay of a few milliseconds at each scanning point. In addition, the complexity of the system is high, due to additional required components, such as laser-focusing parts. This paper proposes a laser imaging method with an increased scanning speed, based on excitation and the measurement of standing waves in structures. The wavenumber of standing waves changes at sections with a geometrical discontinuity, such as thickness. Therefore, it is possible to detect defects in a structure by generating standing waves with a single frequency and scanning the waves at each point by with the laser scanning system. The proposed technique is demonstrated on a wall-thinned plate with a linear thickness variation.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.9
• /
• pp.1093-1098
• /
• 2013

A single-crystal sapphire is used as a transparent bulletproof window material; however, few studies have investigated the dynamic behavior and fracture properties under high-speed impact. High-speed and high-resolution sequential images are required to study the interaction of the bullet with the brittle ceramic materials. In this study, a device is developed to capture the sequence of high-speed impact/penetration phenomena. This system consists of a speed measurement device, a microprocessor-based camera controller, and multiple CCD cameras. By using a linear array sensor, the speed-measuring device can measure a small (diameter: up to 1 2 mm) and fast (speed: up to Mach 3) bullet. Once a bullet is launched, it passes through the speed measurement device where its time and speed is recorded, and then, the camera controller computes the exact time of arrival to the target during flight. Then, it sends the trigger signal to the cameras and flashes with a specific delay to capture the impact images sequentially. It is almost impossible to capture high-speed images without the estimation of the time of arrival. We were able to capture high-speed images using the new system with precise accuracy.