• Nuclear Engineering and Technology
• /
• v.40 no.7
• /
• pp.607-614
• /
• 2008

Since pipes with wall-thinning defects can collapse at fluid pressure that are lower than expected, the collapse moment of wall-thinned pipes should be determined accurately for the safety of nuclear power plants. Wall-thinning defects, which are mostly found in pipe bends and elbows, are mainly caused by flow-accelerated corrosion. This lowers the failure pressure, load-carrying capacity, deformation ability, and fatigue resistance of pipe bends and elbows. This paper offers a support vector regression (SVR) model further enhanced with a fuzzy algorithm for calculation of the collapse moment and for evaluating the integrity of wall-thinned piping systems. The fuzzy support vector regression (FSVR) model is applied to numerical data obtained from finite element analyses of piping systems with wall-thinning defects. In this paper, three FSVR models are developed, respectively, for three data sets divided into extrados, intrados, and crown defects corresponding to three different defect locations. It is known that FSVR models are sufficiently accurate for an integrity evaluation of piping systems from laser or ultrasonic measurements of wall-thinning defects.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11a
• /
• pp.267-270
• /
• 2005

Finite element model of pressurized water reactor internals were obtained using ANSYS software package to analyze dynamic characteristics. The pressure vessel, hold-down ring, alinement key, core support barrel(CSB), upper guide structure(UGS) and fluid gap were fully modeled using structural solid element(SOLID45) and fluid element(FLUID80) which is one of element types. Also modal analysis using the above finite element model has been performed. As a result, it was found that the fundamental beam mode natural frequency of the CSB were 8.2 Hz, the shell mode one 14.5 Hz. To verify the Finite Element Analysis(FEA), we compare the analysis result with experimental data that is obtained from the plant IVMS(internal Vibration Monitoring System). The experimental results are good agreement with the FEA model.

• Journal of Energy Engineering
• /
• v.13 no.4
• /
• pp.259-266
• /
• 2004

Specific heat mechanism of oxide fuel is contributed by lattice vibration, dilatation, conduction electron and defect and excess specific heat. Model of oxide fuel for specific heat consists of specific heat at constant pressure term, dilatation specific heat term and defect specific heat term. In this study experimental and published data on the specific heats of oxide nuclear fuels have been reviewed and analyzed to recommend the best fitting model. The oxide fuels considered in this paper were UO$_2$, mixed (U, Pu) oxides and spent fuel. The specific heat data of spent fuel has been replaced by that of simulated fuel.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.4
• /
• pp.663-667
• /
• 1987

The conventional model of the heat engine involves the inconsistency with the real engine that the power becomes to be zero at the maximum effectiveness condition. In order to improve this defect, a new model of the heat engine is proposed, in which the heat loss from the heat source is taken into account. In accordance with this model, both the power and effectiveness have their respective extremum with respect to operating conditions, and the effectiveness always becomes to be zero when the power is zero.

• Journal of Periodontal and Implant Science
• /
• v.38 no.2
• /
• pp.153-162
• /
• 2008

Purpose: Recombining bone morphogenetic protein (BMP) is usually acquiredfrom high level animals. Though this method is effective, its high cost limits its use. The purpose of this study was to evaluate the effect of bone morphogenetic protein-2 with protein transduction domain (BMP-2/PTD;TATBMP-2) on bone regeneration. Rat calvarial defect model and osteoblastic differentiation model using MC3T3 cell were used for the purpose of the study. Materials and Methods: MC3T3 cells were cultured until they reached a confluence stage. The cells were treated with 0, 0.1, 1, 10, 100, 500 ng/ml of BMP-2/PTD for 21 days and at the end of the treatment, osteoblastic differentiation was evaluated usingvon Kossa staining. An 8mm, calvarial, critical-size osteotomy defect was created in each of 48 male Spraque-Dawley rats (weight $250{\sim}300\;g$). Three groups of 16 animals each received either BMP-2/PTD (0.05mg/ml) in a collagen carrier, collagen only, or negative surgical control. And each group was divided into 2 and 8 weeks healing intervals. The groups were evaluated by histologic analysis(8 animals/group/healing intervals) Result: In osteoblastic differentiation evaluation test, a stimulatory effect of BMP-2/PTD was observed in 10ng/ml of BMP-2/PTD with no observation of dose-dependent manner. The BMP-2/PTD group showed enhanced local bone formation in the rat calvarial defect at 2 weeks. New bone was observed at the defect margin and central area of the defect. However, new bone formation was observed only in 50% of animals used for 2weeks. In addition, there was no new bone formation observed at 8 weeks. Conclusion: The results of the present study indicated that BMP-2/PTD(TATBMP-2) have an positive effect on the bone formation in vitro and in vivo. However, further study should be conducted for the reproducibility of the outcomes.

• Korean Journal of Construction Engineering and Management
• /
• v.18 no.5
• /
• pp.59-67
• /
• 2017

At the completion of the construction, various finishing processes are concentrated. This imposes a burden on the on-site manager and imposes on experience based quality control, thereby causing deviations in the quality of construction depending on supervisor or worker's individual competence. In addition, the information related to quality control is frequently scattered in various types of documents such as specifications and drawings, and checkpoints are frequently omitted. It is necessary to provide a tool that can effectively provide the practitioner before or during the inspection work by systematically storing the information related to the defect prevention and linking them in a mutually referential state. This paper proposes an quality inspection support model that can systematically store necessary information on activity or room basis for the quality check of the apartment house finishing work. Establish a defect prevention information base and a information nexus by linking specifications, design standards, checklists, regulations, defect cases, and drawings to the finishing process and the rooms. Based on this, information registration and search interface are presented. It can contribute to securing a certain level of construction quality or more by suggesting a frame that can be utilized by linking various defects prevention information with the focus on closing activity and room.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.40 no.3
• /
• pp.27-37
• /
• 2017

As the global uncertainty of manufacturing has increased and the quality problem has become global, the recall has become a fatal risk that determines the durability of the company. In addition, as the convergence of PSS (product-service system) product becomes common due to the development of IT convergence technology, if the function of any part of hardware or software does not operate normally, there will be a problem in the entire function of PSS product. In order to manage the quality of such PSS products in a stable manner, a new approaches is needed to analyze and manage the hardware and software parts at the same time. However, the Fishbone diagram, FTA, and FMEA, which are widely used to interpret the current quality problem, are not suitable for analyzing the quality problem by considering the hardware and software at the same time. In this paper, a quality risk assessment model combining FTA and FMEA based on defect rate to be assessed daily on site to manage quality and fishbone diagram used in group activity to solve defective problem. The proposed FTA-FMEA based risk assessment model considers the system structure characteristics of the defect factors in terms of the relationship between hardware and software, and further recognizes and manages them as risk. In order to evaluate the proposed model, we applied the functions of ITS (intelligent transportation system). It is expected that the proposed model will be more effective in assessing quality risks of PSS products because it evaluates the structural characteristics of products and causes of defects considering hardware and software together.

• Journal of Life Science
• /
• v.20 no.8
• /
• pp.1207-1213
• /
• 2010

The purpose of this study was to evaluate the effect of porcine cancellous bone as a scaffold in a rat calvarial defect model. Critical-sized defects were created in 30 male Sprague-Dawley rats. The animals were divided into critical defect (CD, n=10), $\beta$-tricalcium phosphate (TCP) graft (BT, n=10) and porcine cancellous bone graft (PCB, n=10) groups. Each defect was filled with $\beta$-TCP mixed with fibrin glue or porcine cancellous bone powder mixed with fibrin glue. In the CD group, the defect was left empty. All rats were sacrificed at 8 weeks after bone graft surgery, and bone formation was evaluated by gross observation, plain radiography, micro-computed tomography scanning and histological evaluation. Repair of bone defect was the least in the CD group, and significant new bone formation was observed in the PCB group. Grafting of porcine cancellous bone was more efficient for regenerating new bone than grafting $\beta$-TCP.

• Archives of Plastic Surgery
• /
• v.35 no.6
• /
• pp.631-636
• /
• 2008

Purpose: Adipose tissue-derived stem cells(ADSC) has an osteoconductive potential and demineralized bone matrix(DBM) is an osteoinductive material. A combination of DBM and ADSC wound probably create osteoinductive properties. The purpose of this study is to determine the effect of the combination of DBM and ADSC mixture on healing of rat calvarial defect. Methods: Thirty adult male Sprague-Dawley rats were randomized into 3 groups(n=10) as 1) Control, 2) DBM alone, 3) DBM with ADSC mixture. DBM with ADSC mixture group has had a 3-day preculture of ADSC from groin fat pad. An 6 mm critical size circular calvarial defect was made in each rat. Defect was implanted with DBM alone or DBM with ADSC mixture. Control defect was left unfilled. 6 and 12 weeks after the implantation, the rats were sacrificed and the defects were evaluated by histomorphometric and radiographical studies. Results: Histomorphometric analysis revealed that DBM with ADSC mixture group showed significantly higher bone formation than DBM alone group(p<0.05). Although radiographs from DBM alone group and DBM with ADSC group revealed similar diffuse radiopaque spots dispersed throughout the defect. Densitometric analysis of calvarial defect revealed DBM with ADSC mixture group significantly higher bone formation than DBM alone(p<0.05). There was correlation of densitometry with new bone formation(Spearman's correlation of coefficient=0.804, 6 weeks, 0.802, 12 weeks). Conclusion: The DBM with ADSC mixture group showed the best healing response and the osteoinductive properties of DBM were accelerated with ADSC mixture. It will be clinically applicable that DBM and ADSC mixture in plastic and reconstructive surgery, such as alveolar cleft and congenital facial deformities that bone graft should be required.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.2 s.233
• /
• pp.284-292
• /
• 2005

Material flaws in the from of pre-existing defects can severely affect the crack initiation. Stress distribution and crack initiation life of engineering materials such as monolithic aluminum alloy and Al/Glass fiber laminate may be different according to the defect location. The aim of this study is to evaluate effects of relative location of defects around the circular hole in monolithic aluminum and Al/Glass fiber laminates under cyclic bending moment. Stress distribution and crack initiation behavior near a circular hole are considered. Results of Finite Element (FE) model indicated the features of different stress field due to the relative defects positions. Especially, the defects positions at ${\theta}=0^{\circ}\;and\;{\theta}=30^{\circ}$ was strongly effective in stress concentration factor ($K_t$) and crack initiation behavior.