• The Korean Journal of Nuclear Medicine Technology
• /
• v.15 no.2
• /
• pp.72-75
• /
• 2011

Purpose: The HSV1-tk reporter gene system is the most widely used system because of its advantage is that it is possible to monitor directly without the introduction of a separate reporter gene in case of HSV1-tk suicide gene therapy. This study was performed to automate 9-(4-[$^{18}F$] Fluoro-3-hydroxymethylbutyl) guanine ([$^{18}F$] FHBG) that are widely used as substrate for the HSV1-tk reporter gene in living organisms with positron emission tomography (PET) and find the optimized conditions of synthesis. Materials and Methods: Fully automated synthesis of [$^{18}F$] FHBG was performed using Explora-RN (CTI, USA) module. We have changed of reaction time (3, 5, 10 min) and temperature (110, 120, $130^{\circ}C$) for the optimized conditions of synthesis. Also we experimented to find the optimal concentration of precursor (5, 7, 10 mg). Results: [$^{18}F$] FHBG was purified by HPLC system and collected at around 10-12 min. Synthesis using Explora-RN module showed a $32.0{\pm}1.2%$ yield of radiochemical (decay corrected), the purity was greater than 98%. And the entire synthesis time was less than 48 min. Temperature of the highest synthesis yield was $130^{\circ}C$, reaction time was 5 minutes and concentration of precursor was 10 mg (recommended volume in manual) (n=36). In contrast to radiochemical yield of precursor 10 mg ($32{\pm}1.2%$), yield of 5 and 7 mg precursor was unstable. Conclusion: Automation of [$^{18}F$] FHBG synthesis at Explora-RN module has been completed. In addition, we were able to obtain optimized reaction time, temperature and concentration of precursor. Therefore this study would be provided more rapid synthesis and higher radiochemical yield.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.11 no.2
• /
• pp.71-77
• /
• 2001

We investigated photoluminescence, long-phosphorescent and crystalline properties with various $Dy_2$$O_3$ compositions (0.0~9.5mol%) in $SrAl_2$$O_4$ : $Eu^{2+}$,$Dy^{3+}$ phosphor powders prepared by the solid state reaction. The highest emission wavelength (520nm) of photoluminescence spectra was not affected by the Dy doping concentrations. The$SrAl_2$$O_4$single phase which was determined by X-ray diffraction and photoluminescence was appeared for the concentrations of $Dy_2$$O_3$$\leq$1.0 mol%. After removal of the pulsed Xe-lamp excitation (360nm), also, excellent long phosphorescent properties of the phosphors were obtained with the concentrations of $Dy_2$$O_3$$\leq$1.0mol%, although the decay time for all phosphors decrease exponentially.

• Korean Journal of Materials Research
• /
• v.22 no.4
• /
• pp.195-201
• /
• 2012

$Ce^{3+}$-doped yttrium aluminum gallium garnet (YAGG:$Ce^{3+}$), which is a green-emitting phosphor, was synthesized by solid state reaction using ${\alpha}$-phase or ${\gamma}$-phase of nano-sized $Al_2O_3$ as the Al source. The processing conditions and the chemical composition of phosphor for the maximum emission intensity were optimized on the basis of emission intensity under vacuum UV excitation. The optimum heating temperature for phosphor preparation was $1550^{\circ}C$. Photoluminescence properties of the synthesized phosphor were investigated in detail. From the excitation and emission spectra, it was confirmed that the YAGG:$Ce^{3+}$ phosphors effectively absorb the vacuum UV of 120-200 nm and emit green light positioned around 530 nm. The crystalline phase of the alumina nanoparticles affected the particle size and the luminescence property of the synthesized phosphors. Nano-sized ${\gamma}-Al_2O_3$ was more effective for the achievement of higher emission intensity than was nano-sized ${\alpha}-Al_2O_3$. This discrepancy is considered to be because the diffusion of $Al^{3+}$ into $Y_2O_3$ lattice is dependent on the crystalline phase of $Al_2O_3$, which affects the phase transformation of YAGG:$Ce^{3+}$ phosphors. The optimum chemical composition, having the maximum emission intensity, was $(Y_{2.98}Ce_{0.02})(Al_{2.8}Ga_{1.8})O_{11.4}$ prepared with ${\gamma}-Al_2O_3$. On the other hand, the decay time of the YAGG:$Ce^{3+}$ phosphors, irrespective of the crystalline phase of the nano-sized alumina source, was below 1 ms due to the allowed $5d{\rightarrow}4f$ transition of the $Ce^{3+}$ activator.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.185-185
• /
• 2012

중공 발광 나노 물질은 특유의 구조적 특성(낮은 밀도, 높은 비표면적, 다공성 물질, 낮은 열팽창계수 등)과 광학적 성질을 이용하여 디스플레이 패널, 광결정, 약물전달체, 바이오 이미징 라벨 등의 다양한 적용이 가능하다. 이러한 적용에 있어 균일한 크기와 형태의 중공 입자는 필수 조건으로 여겨진다. 지금까지 합성된 중공 발광 입자에는 BaMgAl10O17 : Eu2+-Nd3+, Gd2O3 : Eu3+, $EuPO_4{\cdot}H_2O$과 같은 것들이 있으나 크기 조절이 어렵고, 그 균일성이 확보되지 못하였다. 균일한 크기의 중공 발광 입자를 만들기 위해 SiO2나 emulsion을 템플릿으로 이용하여 황화카드뮴, 카드뮴 셀레나이드 중공 입자를 합성한 예가 있으나, 양자점의 독성으로 인하여 바이오분야 응용에는 적합하지 않다. YAG는 모체로써 형광체에서 가장 많이 이용되는 물질로, 화학적 안정성과 낮은 독성, 높은 양자 효율 등 많은 장점을 갖고 있다. 특히 세륨이 도핑된 YAG형광체의 경우 WLED, 신틸레이터, 바이오산업에 적용이 가능하다. 그러나 지금까지 중공 YAG:Ce3+형광체를 합성한 예가 없었다. 본 연구에서는 단분산 수화 알루미늄 (Al(OH)3) 입자 위에 세륨이 도핑 된 이트륨 베이직 카보네이트 ($Y(OH)CO_3$)를 균일하게 코팅한 후 열처리를 하여 균일한 크기의 Y3Al5O12:Ce3+(YAG) 중공 입자를 합성하였다. 열처리 온도에 따른 고분해능 투과 전자 현미경(HRTEM), X-선 회절(XRD), 고분해능 에너지 분광법(HREDX) 분석결과, 중공 YAG: Ce3+입자는 Kirkendall 효과에 의해 형성됨을 확인하였다. 전계방사형 주사 전자 현미경(FE-SEM) 측정을 통해, 열처리 후에도 입자의 크기와 형태가 균일함을 확인하였으며, 공초점 현미경 관찰을 통해 중공 형태를 명확히 확인 할 수 있었다. Photoluminescence (PL) 분광법과 형광 수명 이미징 현미경(FLIM)을 이용한 광 특성 분석결과, 합성된 입자는 400-500 nm에서 흡수 파장 (456 nm에서 최대 강도)과 500-700 nm 범위의 발광 파장(544 nm에서 최대 강도)을 나타냈고, 상용 YAG: Ce3+(70 ns)에 준하는 74 ns의 잔광 시간(decay time)이 측정되었다. 단분산 수화 알루미늄 입자의 크기를 조절하여 최종 합성된 YAG: Ce3+의 크기를 조절할 수 있었다. 지름 약 600 nm의 Al(OH)3를 사용한 경우, $1,300^{\circ}C$에서 열처리를 한 후 평균 지름 590 nm의 중공입자를 합성하였고, 약 170 nm의 Al(OH)3를 이용하여, 더 낮은 온도인 $1,100^{\circ}C$에서의 열처리를 통해 평균지름 140 nm의 중공 YAG: Ce3+입자를 합성하였다. 본 연구를 통하여 합성된 균일한 크기의 YAG 중공입자는 LED와 같은 광전변환 소자 및 다기능성 바이오 이미징 등의 나노바이오 소자 분야에 활용될 수 있음이 기대된다.

• KSBB Journal
• /
• v.6 no.3
• /
• pp.309-319
• /
• 1991

A continuous stirred tank membrane reactor(CSTMR ) was developed and optimized for the production of cod skin gelatin hydrolyzates using endo-protease Alcalase. A experimental design methodology was used to optimize the four performance variables: enzyme concentration, substrate concentration, permeate flux and reactor volume. All four variables studied had an effect on substrate conversion, with enzyme and substrate concentrations being predominant. Conversion increased with the increase in enzyme concentration, with the decrease in substrate concentration, at high volumes and low flux. A strong interaction was observed between enzyme and substrate concentrations and smaller interactions between enzyme and flux and substrate and flux. The optimum operating conditions for the CSTMR process for an initial substrate concentration for 10% were $50^{\circ}C$, pH 8, flux 7.3ml/min, residence time 82 min, and Alcalase to substrate ratio 0.02(w/w). A gradual decay in reactor activity during 8 hrs was 2.1% conversion/hr. Enzyme leakage through the 10, 000 MWCO membrane was 16% at $50^{\circ}C$ and 12% at $35^{\circ}C$, 6hrs. However, there was no apparent correlation between enayme leakage and substrate conversion. The Km value for the CSTMR was 20 times higher than the batch reactor. The productivity(expressed as mg product/mg enzyme) of the CSTMR was more than six fold higher than the batch at $50^{\circ}C$. The hydrolyzate was non-bitter.

• Applied Biological Chemistry
• /
• v.10
• /
• pp.63-68
• /
• 1968

The effects of $^{60}Co-{\gamma}$ radiation on the change of composition and susceptibility to soft rot during the storage of sweetpototoes and the radioresistance of spores of the soft rot fungus were investigated and the following results were obtained. 1) Gamma-irradiation of sweetpotatoes caused the increase in water-soluble sugar content and the decrease in ascorbic acid content during the storage. 2) The rate of oxygen uptake in sweetpotato slices becomes higher as the dose increases. But the oxygen uptake in slices irradiated with higher doses decreases along with the color change as the time passes. 3) Irradiation with high doses (above $2.5{\times}10^5$ rad) brought about the increased susceptibility to soft rot decay as the chilling injury did in the storage of sweetpotatoes. 4) Average lethal dose for the spores of Rhizopus nigricans was $3.0{\times}10^5$ rad and the complete death required the level of $1.25{\times}10^6$ rad.

• Journal of Radiation Protection and Research
• /
• v.22 no.2
• /
• pp.119-125
• /
• 1997

PHWR achieves high neutron economy by adopting heavy water as its moderator and coolant. On the other hand it permits much tritium generation, compared to LWR, due to the neutron capture reaction of deuterium in heavy water. Meanwhile in the reactor core, $^3He formed as the result of-decay of tritium, captures a thermal neutron and transforms to tritium again. The existing calculation models on tritium generation in PHWR neglect the contribution of $^3He$ in both moderator and coolant due to its relatively low solubility. However the neutron capture cross-section of $^3He$ is almost $1.6{\times}10^7$ times as large as that of deuterium. That means that the dissolved amount of 0.03 ppm of $^3He$ in heavy water is enough to generate the same amount of tritium as that generated by the deuterium of total heavy water in the system. This study dealt with the contribution of $^3He$ to tritium generation. As a sample case, the contribution of $^3He$ to the tritium generation in Wolsong #1 was evaluated and compared to the measured values. According to the result of this study, it is concluded that $^3He$ in coolant contributes very much to the tritium generation but that in moderator shows negligible effects due to the low solubility and $^4He$ cover gas. At the beginning of the plant operation, the contribution of $^3He$ is slightly greater than the measured value but agrees well with the measured as the operating time increases.

• Horticultural Science & Technology
• /
• v.34 no.4
• /
• pp.644-654
• /
• 2016

Supervised residue trials for mandipropamid in Korean cabbage(Brassica campestris L.) were conducted to establish its pre-harvest residue limit (PHRL), a criterion to ensure the safety of the terminal pesticide residue during cabbage production. Tissues of Korean cabbage were collected at 0, 1, 3, 5, 7, and 10 days after mandipropamid application and subjected to residue analysis. The analytical method was validated by recoveries ranging from 88.2-92.2% at two levels (0.4 and $2.0mg{\cdot}kg^{-1}$), and a limit of quantitation (LOQ) of $0.04mg{\cdot}kg^{-1}$. Mandipropamid residues in Korean cabbage gradually decreased over time. The dissipation rate of the residue would be affected by intrinsic degradation of the compound along with dilution resulting from the fast growth of Korean cabbage. The decay pattern was well fitted by simple first-order kinetics. Biological half-lives of mandipropamid in Korean cabbage ranged from 3.9-4.0 days in two field conditions. Calculated by the regression curve of mandipropamid dissipation, the PHRLs of mandipropamid in Korean cabbage were recommended as 11.07-12.19 and $5.76-6.05mg{\cdot}kg^{-1}$ for 10 and 5 days prior to harvest, respectively.

• Journal of Soil and Groundwater Environment
• /
• v.6 no.2
• /
• pp.49-56
• /
• 2001

Benzene, one of the aromatic hydrocarbons, can be degraded by physical, chemical and biological processes in aquifers. This study aimed at analyzing separately the three different forms of degradation by performing column tests. Column tests using KCl and benzene as tracers were conducted for four different cases: 1) no hydrogen peroxide and no microorganism, 2) hydrogen peroxide only; 3) microorganism only; 4) hydrogen peroxide and microorganism to investigate the sorption and degradation of benzene. The observed BTCs of KCl and benzene in all cases showed that the arrival times of the peaks of both tracers coincided well but the peak concentration of benzene was much lower than that of KCl. This reveals that a predominant process affecting the transport of benzene in a sandy soil is an irreversible sorption and/or degradation rather than retardation. Decay of benzene through sorption and degradation increased with the addition of hydrogen peroxide and/or microorganism. Dissolved oxygen decreased with the increase of benzene in all cases indicating that degradation of benzene was also influenced by dissolved oxygen. For BTCs with the addition of microorganisms (case 3 and case 4), microorganism showed much lower concentrations compared to the initial levels and an increasing tendency with time although concentrations of benzene returned to zero, indicating a possible retardation of microorganism due to reversible and irreversible sorption to the particle surfaces.

• Journal of KIISE:Computer Systems and Theory
• /
• v.34 no.5_6
• /
• pp.249-256
• /
• 2007

GPS(generalized processor sharing) is a fair scheduling scheme that guarantees fair distribution of resources in an instantaneous manner, while virtual clock pursues fairness in the sense of long-term. In this paper, we notice that the degree of memorylessness is the key difference of the two schemes, and propose a unified scheduling model that covers the whole spectrum of history-sensitiveness. In this model, each application's resource right is represented in a value called deposit, which is accumulated at a predefined rate and is consumed for services. The unused deposit, representing non-usage history, gives the application more opportunity to be scheduled, hence relatively enhancing its response time. Decay of the deposit means partial erase of the history and, by adjusting the decaying rate, the degree of history-sensitiveness is controlled. In the spectrum, the memoryless end corresponds GPS and the other end with full history corresponds virtual clock. And there exists a tradeoff between average delay and long-term fairness. We examine the properties of the model by analysis and simulation.