• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.561-564
• /
• 2003

The machining technology for the removal of micro-burr has been demanded because electrode parts of electron gun have minute holes. In this study, Magnetic Assisted Polishing(MAP) is applied to remove the micro-burr instead of the contentional polishing process such as the etching and barrel. Optimal polishing conditions are selected from many experiments using the tool of the flat end slit type. On the basis of experimental results, the deburring machine for the Magnetic Assisted Polishing of electrode part is developed and its performance is evaluated.

• 한국생산제조학회지
• /
• 제19권3호
• /
• pp.407-413
• /
• 2010

This paper reports on the research which analyzes acoustic signals acquired in progressive compressing, hole blanking, and burr compacting process. An acoustic sensor was set on the bed of hydraulic press. Acoustic signal is generated from progressive stamping process. First the signal acquired from the unit process; compressing, blanking or compacting, is studied by Fourier Transform and Short Time Fourier Transform. The blanking process emitted ultrasonic signal with more than 20kHz, but the compressing and compacting processes emitted acoustic signals with lower than 10kHz. The combined signals periodically acquired right after the tool grinding were then analyzed. 70-80kHz signals appeared in time-frequency domain, but not in the frequency domain, the magnitude of which was related to the tool wear. Short Time Fourier Transform made up for the Fourier Transform in analyzing the emitted signal for stamping process in the ultrasonic domain.

• 한국기계가공학회지
• /
• 제21권9호
• /
• pp.12-20
• /
• 2022

Delamination and burr defects are important problems in drilling fiber reinforced plastics. A method for measuring FRP drilling defects has been studied. Delamination and burr factors were defined as the relative length or area. Using these factors, the effects of tool shape and drilling conditions on delamination and burr were studied. In this study, the defects that occur when drilling a glass-carbon fiber hybrid composite were compared in terms of three factors. In the glass-carbon fiber hybrid composite, the effects of the feed rate and tool point angle on the delamination and burr factors were similar to those in previous studies. The diameter of the tool did not affect the defect factor. A circular burr was generated in a drill tool with a point angle of 184°, and a relatively small deburring factor was observed compared with a tool with a point angle of 140°.

• 한국공작기계학회논문집
• /
• 제16권1호
• /
• pp.33-39
• /
• 2007

One of the most important processes is the face milling in processing task. It makes the smooth surface of processed goods. In processing stage, the formation of burr is inevitable. The formed burr decreases a detailed drawing and effects the safety of workers. So, it causes a deburring process for removing and a bottle-neck condition. Therefore, the study which can minimize the generation of burr is needed. In this paper, complex feature, such as line, arc, circle, spline is studied more reality than any other papers. And also, the algorithm which can predict the path of generated burr is established. Moreover, the finality goal is that the system which can produce tool-path minimized has to be developed.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 춘계학술대회논문집
• /
• pp.161-164
• /
• 1999

In order to investigate the effect of punching condition on the stretch flange formability of sheet for deep drawing hole expansion tests at various edge condition were done. Edge conditions were changed by altering tool clearances artifical defects grinding and deburring. For a determination of optimum edge condition of side panel of automobile punched section analysis and forming results were studied and the laboratory test results were used. In case of considered side panel tool clearance should be less than 15% and punched edge should be uniform without defects for safe forming

• 한국생산제조학회지
• /
• 제21권6호
• /
• pp.926-931
• /
• 2012

Rotary bar was cutting tool being in use for deburring scale after welding metal and for eliminating sharp edges. It was necessary to develop exclusive 6-axis machine being possible to process machining continuously for making an cutting edge of rotary bar and to revise easily machining program. This study aimed at the structural analysis of strength according to the configuration of new made 6-axis machine and at the machining accuracy and durability of rotary bar. As a result of test, the runout of new rotary bar manufactured out of 6-axis machine was decreased from 0.385 mm to 0.027mm extensively than old one. And good cutting ability and durability was obtained equal quality compared with imported products.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1816-1819
• /
• 2003

As a result of milling operation, we expect to have burr at the outward edge of workpiece. Also, it causes undesirable problems such as deburring cost, low quality of machined surface, and bottleneck in manufacturing process. Though it is impossible to totally remove burr in machining, it is necessary to plan a machining process that minimizes the occurrence of burr. In this paper, a scheme is proposed which identifies the tool path of the milling operation with minimum burr. In the previous research, a Burr Expert System was developed where the feature identification, the cutting condition identification, and the analysis on exit burr formation are the key steps in the program. The Burr Expert System predicts which portion of workpiece would have the exit burr in advance so that we can calculate the burr length of each milling operation. Here, the critical angle determines whether the burr analyzed is an exit burr or not. So the burr minimization scheme becomes to minimize the burr with critical angle. By iterating all the possible tool paths in certain milling operation, we can identify the tool path with minimum burr.

• 한국기계가공학회지
• /
• 제16권4호
• /
• pp.16-23
• /
• 2017

CFRP(Carbon Fiber Reinforced Plastics) has many industrial applications due to its low weight and high strength properties. Due to its superior properties, for example, excellent resistance to fatigue wear, corrosion, and breakage from fatigue, it has been widely applicable to aircraft, automotive, and medical industries and so on. The main machining for CFRP is drilling, and route milling. In case of drilling, the machining defects such as the delamination of each layer, uncut fiber, resin burning, spalling, and exit burrs are inevitable. The issue to remove such kind of defects is necessary to make CFRP parts successful. From this point of view, this paper investigates the removal effectiveness of machining defects existing at exit region with different type of tool geometries. Consequently, based on the experiments, the tool geometry is most impact factor to remove uncut fiber or resin.

• 산업공학
• /
• 제18권3호
• /
• pp.247-252
• /
• 2005

In the automated production environment in the present days, the minimization of manual operation becomes a very important factor in increasing the efficiency of the production system. The exit burr produced through the milling operation on the edge of workpiece usually requires manual deburring process to enhance the level of precision of the resulting product. So far, researchers have developed various methods to understand the formation of exit burr in cutting process. One method to analytically identify the formation of exit burr was to use the geometrical information of CAD and CAM data used in automated machining. This method, in turn, generated the information resulting from the analysis such as burr type, cutting region, and exit angle. Up to now, the geometrical data were restricted to the single feature and single path. In this paper, a method to deal with the complicated geometric features such as line segment, arc, hole, and spline will be presented and validated using the field data. This method also deals with the complex workpiece shape which is a combination of multiple features. As for the cutting path, multiple tool path is analyzed in order to simulate the real cutting process. All this analysis is combined into a Windows based software and real data are used to validate the program in the conclusion.

• 한국소음진동공학회논문집
• /
• 제19권4호
• /
• pp.386-392
• /
• 2009

This paper reports on the research which investigates acoustic signals acquired in progressive compressing, hole blanking, shearing and burr compacting process. The work piece is the head pin of the electric connector, whose raw material is the preformed steel bar. An acoustic sensor was set on the bed of hydraulic press. Because the acquired signals include the dynamic characteristics generated for all the processes, it is required to investigate signal characteristics corresponding to unit process. The corresponding dynamic characteristics to the respective process were first studied by analyzing the signals respectively acquired from compressing, blanking and compacting process. The combined signals were then periodically analyzed from the grinding to the grinding in the sound frequency domain and in the ultrasonic wave. The frequency of around 9 kHz in the sound frequency domain was much correlated to the tool wear. The characteristic frequency in the acoustic emission domain between 100 kHz and 500 kHz was not only clearly observed right after tool grinding but its amplitude was also related to the wear. The frequency amplitudes of 160 kHz and 320 kHz were big enough to be classified by the noise. The noise amplitudes are getting bigger, and their energy was much bigger as coming to the next regrinding. The signal analysis was based on the real time data and its frequency spectrum by Fourier Transform. As a result, the acousto-ultrasonic signals were much related to the tool wear progression.