• KEPCO Journal on Electric Power and Energy
• /
• v.6 no.4
• /
• pp.405-411
• /
• 2020

In this paper, we designed the COS MEMS system for sensing the falling detection and explosive noise of fuse link in COS (Cut Out Switch) installing on the power distribution. This system analyzed the failure characteristics and an instantaneous breakdown of power distribution. Therefore, our system strengths the industrial competence and guaranties the stable power supply. In this paper, we applied BLE (Bluetooth Low Energy) technology which is suitable protocol for low data rate, low power consumption and low-cost sensor applications. We experimented with LSM6DSOX which is system-in-module featuring 3 axis digital accelerometer and gyroscope boosting in high-performance mode and enabling always-on low-power features for an optimal motion for the COS fuse holder. Also, we used the MP34DT05-A for gathering an ultra-compact, low power, omnidirectional, digital MEMS microphone built with a capacitive sensing element and an IC interface. The proposed COS MEMS system is developed based on nRF52 SoC (System on Chip), and contained a 3-axis digital accelerometer, a digital microphone, and a SD card. In this paper of experiment steps, we analyzed the performance of COS MEMS system with gathering the accelerometer raw data and the PDM (Pulse Data Modulation) data of MEMS microphone for broadcasting the failure of COS status.

• Proceedings of the KSRS Conference
• /
• v.2
• /
• pp.784-787
• /
• 2006

Dual-polarized transmission is one of the effective methods to transmit such a high speed data thanks to two independent channel leads to the orthogonal feature between RHCP (Right-Hand Circular Polarization) and LHCP (Left-Hand Circular Polarization). However, in practical case, the transmitted signal by RHCP polarized antenna in satellite can be occurred at the output port of LHCP polarized antenna in ground station, vice versa. XPD (Cross-Polarization Discrimination) is the ratio of the signal level at the output of a receiving antenna that is nominally co-polarized to the transmitting antenna to the output of a receiving antenna of the same gain but nominally orthogonally polarized to the transmitting antenna. In this paper, the detailed estimation of XPD within the interface between satellite and ground station is written and the influence of XPD to link performance is also described.

• The Magazine of the IEIE
• /
• v.22 no.12
• /
• pp.27-44
• /
• 1995

초고속 통신망에 근간이 되는 ATM 통신망에 SUN W/S, PC 컴퓨터들을 접속시키는 ATM Adapter Card은 하드웨어, 시스템 소프트웨어 및 응용 소프트웨어로 구성된다. 하드웨어의 구조 및 시스템 소프트웨어의 구조, 성능에 따라서 ATM Adapter Card 위에서 수행되는 응용 소프트웨어의 성능을 결정할 것이다. ATM Adapter Card는 효율적으로 Native ATM 응용 소프트웨어를 지원할 뿐 아니라, 기존의 TCP/IP 응용 소프트웨어를 수용하는 IPoverATM, LAN Emulation 기능도 지원하여야 한다. 또한 PVC(Permanent Virtual Channel), SVC(Siganlling Virtual Channel)을 위하여 ATM Forum UNI 3.1에 준한 Signalling도 필요하다. 이러한 조건들을 만족시키기위하여, 현재 개발 완료된 SUN W/S SBus용 디바이스 드라이버는 DLPI(Data Link Provider Interface), STREAM 방식으로 구현하였으며, 현재 개발 중인 PC PCI용 ATM Adapter Card의 디바이스 드라이버는 NDIS 3.0 방식으로 구현 다양한 Transport Layer를 ATM망에 수용하도록 하였다. Signalling은 Daemon Process를 이용하여 구현하였다.

• The KIPS Transactions:PartA
• /
• v.12A no.5 s.95
• /
• pp.421-426
• /
• 2005

In a large scale parallel computation, some processor or communication link failure results in a waste of huge amount of CPU hours. However, MPI in its current specification gives the user no possibility to handle such a problem. In this paper, we propose an application-level fault tolerant linear system solver by using an MPMD-type asynchronous iteration, purely on the basis of the MPI standard without using any non-standard fault-tolerant MPI library.

• Proceedings of the KIEE Conference
• /
• 1988.07a
• /
• pp.261-264
• /
• 1988

In this paper, a transmission protocol including error recovery strategy on the data link layer for Ethernet using CSMA/CD media accessing method was proposed. So when considering the actual transmission error probability on the channel, it's performance was analyzed through a simulation. Performming the simmulation, the required parameters was taken as those given by Ethernet controller interface board.

• Proceedings of the KIEE Conference
• /
• 2002.07d
• /
• pp.2800-2802
• /
• 2002

본 연구는 철도신호 장치간 인터페이스를 위한 데이터 링크제어의 성능분석을 위하여 Matlab/simulink을 이용한 시뮬레이션과 시뮬레이터 개발을 목표로 하였다. 이를 위해 Simulink 윈도우상의 데이터 링크제어 시스템 화면에서 사용자 인터페이스 블록을 통해 통신 파라미터들을 선택하여 시뮬레이션을 행할 수 있는 시뮬레이션 툴과, Matlab이 제공하는 RS232통신용 API 기능을 이용하여 철도 신호장치간의 통신 프로토콜을 PC상에서 모사할 수 있는 프로토타입 시뮬레이터를 개발하였다.

• ETRI Journal
• /
• v.36 no.6
• /
• pp.960-967
• /
• 2014

In this paper, an analytical framework is proposed for the optimization of network performance through joint congestion control, channel allocation, rate allocation, power control, scheduling, and routing with the consideration of fairness in multi-channel wireless multihop networks. More specifically, the framework models the network by a generalized network utility maximization (NUM) problem under an elastic link data rate and power constraints. Using the dual decomposition technique, the NUM problem is decomposed into four subproblems - flow control; next-hop routing; rate allocation and scheduling; power control; and channel allocation - and finally solved by a low-complexity distributed method. Simulation results show that the proposed distributed algorithm significantly improves the network throughput and energy efficiency compared with previous algorithms.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1678-1679
• /
• 2007

This paper is the electric power system remote control of semiconductor plasma manufacturing equipment using PLC(power line communication). PLC is useful for economical data link but various problems and limitations are caused in using power lines for communications channel Develop of Semiconductor plasma manufactur ing equipment and remote automation technologies of tool develops day after day and standards. Also, Remote electric power control and device module control by GUIRCS(Graphic User Interface Remote Control System) of tool are monitoring in real time.

• Steel and Composite Structures
• /
• v.32 no.4
• /
• pp.537-548
• /
• 2019

This paper introduces an improved numerical model which can consider the bond-slip effect in steel-concrete composite structures without taking double nodes to minimize the complexity in constructing a finite element model. On the basis of a linear partial interaction theory and the use of the bond link element, the slip behavior is defined and the equivalent modulus of elasticity and yield strength for steel is derived. A solution procedure to evaluate the slip behavior along the interface of the composite flexural members is also proposed. After constructing the transfer matrix relation at an element level, successive application of the constructed relation is conducted from the first element to the last element with the compatibility condition and equilibrium equations at each node. Finally, correlation studies between numerical results and experimental data are conducted with the objective of establishing the validity of the proposed numerical model.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.10
• /
• pp.964-970
• /
• 2013

This paper presents a bandpass wireless 3-D chip to chip interface technique. The proposed technique uses direct amplitude modulation of the free running oscillator which especially utilizes the coupling capacitance between two stacked chips as a part of the resonator. Therefore, the oscillator is three dimensionally configured and a simple envelope detector can be used as a receiver without any additional matching circuitry. The proposed link was designed and fabricated using 110 nm CMOS technology and experimental results successfully showed the data transmission at a data rate of 2 Gb/s for the stacked chips with a thickness of 50 ${\mu}m$ consuming 4.32 mW. The sizes of the Tx and Rx chips are 0.045 $mm^2$ and 0.029 $mm^2$, respectively.