• Journal of Electrical Engineering and Technology
• /
• v.10 no.3
• /
• pp.1138-1143
• /
• 2015

Effects of fabrication process variations on impedance of microelectrodes integrated on a neural probe were examined through equivalent circuit modeling and SPICE simulation. Process variation and the corresponding range were estimated based on experimental data. The modeling results illustrate that the process variation induced by metal etching process was the dominant factor in impedance variation. We also demonstrate that the effect of process variation is frequency dependent. Another process variation that was examined in this work was the thickness variation induced by deposition process. The modeling results indicate that the effect of thickness variation on impedance is negligible. This work provides a means to predict the variations in impedance values of microelectrodes on neural probe due to different process variations.

• Proceedings of the KSME Conference
• /
• 2000.11a
• /
• pp.743-746
• /
• 2000

Plastic microlenses play an important role in reducing the size, weight, and the cost of the systems in the fields of optical data storage and optical communication. In the present study, plastic microlens arrays were fabricated using micro-compression molding process. The design and fabrication procedures for mold insert were simplified by using silicon instead of metal. A simple but effective micro compression molding process, which uses polymer powder, were developed for microlens fabrication. The governing process parameters were temperature and pressure histories and the micromolding process was controlled such that the various defects developing during molding process were minimized. The radius and magnification ratio of the fabricated microlens were $125{\mu}m$ and over 3.0, respectively.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.8
• /
• pp.1242-1245
• /
• 2001

Plastic microlenses play an important role in reducing the size, weight, and the cost of the systems in the fields of optical data storage and optical communication. In the present study, plastic microlens arrays were fabricated using micro-compression molding process. The design and fabrication procedures for mold insert were simplified by using silicon instead of metal. A simple but effective micro compression molding process, which uses polymer powder, were developed for microlens fabrication. The governing process parameters were temperature and pressure histories and the micromolding process was controlled such that the various defects developing during molding process were minimized. The radius and magnification ratio of the fabricated microlens were 125$\mu\textrm{m}$ and over 3.0, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1994.05a
• /
• pp.130-132
• /
• 1994

We fabricated Ag ion exchange glass waveguide. Generally, ion-exchange glass waveguide. are suitable for passive integrated optical components such as directional and star couplers. Its advantages include low loss, ease of fabrication, and low material cost. So, we faricated Ag ion-exchange glass waveguides in AgNO$_3$ melt solution from 2 mole %. And we used Sodalime glass as a substrate in the fabrication process. As the results, we observed multivalent ion-exchange in a typical sodalime glass. Diffusion coefficient and depth are predicted by actual experimental data of Stewart. The exchange rate in silver-ion-exchanged waveguides are compared to the exchange time of waveguide fabrication.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.3
• /
• pp.139-146
• /
• 2004

In this study, to achieve the optimal conditions for mechanical hyper-fine pattern fabrication process, deformation behavior of the materials during indentation scratch test was studied with numerical method by ABAQUS S/W. Brittle materials (Si, Pyrex glass 7740) were used as specimens, and forming conditions to reduce the elastic recovery and pile-up were proposed. The indenter was modeled as a rigid surface. Minimum mesh sizes of specimens are 1-l0nm. Variables of the nanoindentation scratch test analysis are scratching speed, scratching load, tip radius and tip geometry. The nano-indentation scratch tests were performed by using the Berkovich pyramidal diamond indenter. Comparison between the experimental data and numerical result demonstrated that the FEM approach can be a good model of the nanoindentation scratch test. The result of the investigation will be applied to the fabrication of the hyper-fine pattern.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.12
• /
• pp.102-107
• /
• 2007

This paper proposes a H.264/AVC entropy decoder without embedded processor nor memory fabrication process. Many researches on H.264/AVC entropy decoders require ROM or RAM fabrication process, which is difficult to be implemented in general digital logic fabrication process. Furthermore, many researches require embedded processors for bitstream manipulation, which increases area and power consumption. This papers proposes hardwired H.264/AVC entropy decoder without embedded processor, which improves data processing speed and reduces power consumption. Furthermore, its CAVLC decoder optimizes lookup table and internal buffer without embedded memory, which reduces hardware size and can be implemented in general digital logic fabrication process without ROM or RAM fabrication process. Designed entropy decoder was embedded in H.264/AVC video decoder, and it was verified to operate correctly in the system. Synthesized in TSMC 90nm fabrication process, its maximum operation frequency is 125MHz. It supports QCIF, CIF, and QVGA image format. Under slight modification of nC register and other blocks, it also support VGA image format.

• Journal of Technologic Dentistry
• /
• v.38 no.4
• /
• pp.327-342
• /
• 2016

Purpose: The purpose of this study was to investigate the cognition of denture fabrication activities and its cost in National Health Insurance for elderly denture. Methods: A self-administered questionnaire was completed by 41 dental laboratories' owner who was research subjects of HIRA(Health Insurance Review & Assessment Service)'s policy research for elderly denture in 2011. The questionnaire consisted of general characteristics of the subjects, dental technicians' knowledge of national health insurance coverage of elderly denture, job-related changes after national health insurance coverage of elderly denture including validity of denture fabrication activity classification and the cost for each service. Each question was measured by Likert 5 point scale or frequency. The collected data were analyzed by SPSS 16.0. Results: Most of the research subjects had been fabricating national health insurance coverage denture(92.7%), also had ample knowledge of national health insurance coverage denture for elderly. Job-related changes after national health insurance coverage of elderly denture revealed marginal differences in the quality. The validity of fabrication activity classification of resin based complete denture was $3.71{\pm}1.023$ by Likert 5 point scale. Conclusion: The goal of national health insurance for elderly denture is to promote elderly's health and well-being. To fabricate denture is a very important part of the denture treatment. For this reason, denture fabrication activity classification and the cost analysis plan should be duly reflected in the policy of national health insurance for elderly denture.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.37 no.1
• /
• pp.16-22
• /
• 2021

Purpose: The purpose of this study is to investigate the effect of surface polishing and fabrication method on the flexural strength of temporary restorative resin. Materials and Methods: Each of four fabrication methods was used to make 30 temporary restorative resin specimens and the specimens were divided into two groups depending on whether they were polished by mechanical polishing. Specimens were stored in 37℃ thermostat for 24 hours. Flexural strength was measured using a universal testing machine (UTM). The data obtained through the experiment were analyzed with Two-way ANOVA, Tukey's HSD test and Paired t-test. Results: CAD/CAM milling group showed the highest flexural strength regardless of surface polishing. In decreasing order, the flexural strength of the other fabrication method group was as follows SLA 3D printing, DLP 3D printing, and Conventional method group. Conclusion: Surface polishing did not affect flexural strength of the temporary restorative resin (P > 0.05). However, there were statistically significant differences in flexural strength depending on fabrication method (P < 0.05).

• Journal of Korea Multimedia Society
• /
• v.22 no.12
• /
• pp.1385-1395
• /
• 2019

In this paper, we propose a method to fabricate a patient-specific breast implant using MRI images and 3D scan data. Existing breast implants for breast reconstruction surgery are primarily fabricated products for shaping, and among the limited types of implants, products similar to the patient's breast have been used. In fact, the larger the difference between the shape of the breast and the implant, the more frequent the postoperative side effects and the lower the satisfaction. Previous researches on the fabrication of patient-specific breast implants have used limited information based on only MRI images or on only 3D scan data. In this paper, we propose an algorithm for the fabrication of patient-specific breast implants that combines MRI images with 3D scan data, considering anatomical suitability for external shape, volume, and pectoral muscle. Experimental results show that we can produce precise breast implants using the proposed algorithm.

• The Journal of Society for e-Business Studies
• /
• v.8 no.4
• /
• pp.53-68
• /
• 2003

Currently, it is possible to buy almost anything from books(Amazon.com) to airplane tickets(Travelocity.com) using the world wide web. The purpose of this research is to develop a "clean interface" between design and fabrication facilities for the production of custom machined parts through Internet. The current mechanism for production of prototype parts that can be fabricated using standard machine tools like milling machines, requires a process of part description preparation, bidding, contract award, and finally fabrication and delivery of the part. This is a substantially more complex process than buying a book or airplane ticket. In this paper, we try to define the ambiguous part description using XML based data exchange format and to enable e-commerce in this field. The research accomplishments are summarized: 1. Creation of a new format for data exchange of machined prototype parts, 2. Development of a prototype system to illustrate how the XML data can be effectively used to conduct e-Commerce for custom machined parts, 3. Testing of the methodology with a number of parts.