• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 추계학술발표대회 논문집
• /
• pp.216-219
• /
• 2002

Conventional piezoelectric lead-zirconate-titanate (PZT) senor has high sensitivity, but it is very brittle. Recently polymer films such as polyvinylidene fluoride (PVDF) have been used use as a sensor. The advantages of PVDF are the flexibility and mechanical toughness. Simple process and possible several shapes are also additional advantages. PVDF sensor can be directly embedded and attached to a structure. In this study, PVDF sensor was embedded in single glass fiber/epoxy composites whereas PZT sensor with AE was attached to single fiber composites (SFC). Piezoelectric sensor responds to interfacial damage of SFC. The signals measured by PVDF sensor were compared to PZT sensor. PZT sensor detected the signals of fiber fracture, matrix crack, interfacial debonding and even sensor delamination, whereas PVDF sensor only detected fiber fracture signals so far, because PZT sensor is much more sensitive than current PVDF sensor. Wave voltage of fiber fracture measured by PVDF sensor was lower than that of PZT sensor, but the results of fast Fourier transform (FFT) analysis were same. Wave velocity using two PZT sensors was also studied to know the internal and surface damage effect of epoxy specimens.

• 한국항해항만학회지
• /
• 제32권3호
• /
• pp.215-221
• /
• 2008

구조물의 대표적 동적특성인 고유진동수 및 모드형상은 손상평가, 구조계추정기법 등과 결합한 구조건전성 평가분야에서 매우 중요한 기초 자료로 활용되고 있다. 그러나 해양구조물이나 대경간 교량과 같은 대형 구조물의 경우 진동원을 정확히 계측하기 힘들기 때문에 소규모의 구조물에 많이 쓰이는 기존의 모달 테스트 기법으로는 구조물의 진동특성을 구할 수 없다. 본 논문에서는 경간이 긴 대형 트러스 구조물을 대상으로 가속도 응답만으로 고유진동수 및 모드형상을 추출할 수 있는 방법을 연구하였다. 트러스 구조물의 수치해석 모델을 이용하여 가속도 응답 및 주파수 응답함수의 생성과정, 모드분석을 통한 고유진동수 및 모드형상 추출과정을 상세히 설명하였다. 제안한 방법으로 얻은 모드형상은 고유치 해석으로부터 계산된 모드형상과 비교하여 정확성을 검증하였으며, 모의 손상을 통한 손상평가기법에 적용하여 타당성을 입증하였다.

• 한국인터넷방송통신학회논문지
• /
• 제24권2호
• /
• pp.133-138
• /
• 2024

리튬이온 배터리는 높은 에너지 밀도 빠른 충전조건 긴 사이클수명의 특성으로 여러 분야에서 사용되고 있다. 하지만 리튬이온 배터리는 과충전, 과방전, 물리적손상, 고온에서의 사용은 배터리 수명 감소와 보호회로 손상에 의한 화재 및 폭발에 의한 인명피해를 입힐 수 있다. 이러한 배터리의 위험성을 낮추며 배터리 성능을 향상시키기 위해서는 충전 및 방전 과정에서의 특성들을 분석하고 이해하여야 한다. 따라서 본 논문에서는 배터리 충방전기와 시뮬레이터를 활용하여 리튬이온 배터리의 충전 및 방전 특성을 분석하여 과충전 과방전에 따른 배터리 수명 감소와 보호회로 손상에 의한 화재 및 폭발에 의한 인명피해를 줄이고자 한다.

• 품질경영학회지
• /
• 제31권4호
• /
• pp.226-238
• /
• 2003

Recently, The problems with which our country's company is confronted for business of manufacturing goods. This study set the hypothesis to develop the method that was analysis and application of A reliability evaluation method of environmental material for circuit components in Computer, Color TV, Monitor, Microwave oven, Electric Refrigerator, Automobile parts, other goods. Especially, this study emphasis on regulate export of the EU and North America that it's a environmental material's hazards problem. In this process, this study set the pattern of practical application. Therefore, this study emphasis on the application of A reliability evaluation method of environmental material and the use of other parameters by environmental reliability test data. The result of this study is as follows. 1) There is relationship between regulate material and technical protecting system. 2) Characteristics of hazard materials is operating a healthcare damage factor as well as regulate environmental factors.

• 한국공간구조학회논문집
• /
• 제18권4호
• /
• pp.23-30
• /
• 2018

The purpose of this study is to evaluate the structural safety of cultural altar since its bearing capacity has been questioned due to weathering damages and sectional defections. This evaluation process consists two stages; which the first is field investigation and the second is structural modeling and analysis. Based on field investigation, all of the structural members supporting the altar were carefully examined and all the findings were accounted for the development of the structural modeling using the Midas computer program. Using a 3D scanner, the weight of the Buddha statue was applied to the structural modeling. Then, according to the allowable stress design method of KBC2016, the structural safety was evaluated. Based on this result, replacements of several structural members were recommended to increase the structural safety and value of cultural property.

• 한국기계가공학회지
• /
• 제9권1호
• /
• pp.25-34
• /
• 2010

Fretting damage reduces fatigue life of the material due to low amplitude cyclic sliding and changes in the contact surfaces of strongly connected machine and structures such as bolt, key, fixed rivet and connected shaft, which have relative slip of repeatedly very low frequency amplitude. In this study, the fretting fatigue behavior of 7050-T7451 aluminum alloys used mainly in aircraft and automobile industry were evaluated. The plain fatigue test and fretting fatigue test under cyclic bending load carried out commercial bending fatigue tester and specially devised equipments to cause fretting damage. From these experimental work, the following results obtained: (1) The plain fatigue limit for stress ratio R=-l was about 151MPa. (2) In case of fretting fatigue, fatigue limit for stress ratio R=-l about 72MPa, the fatigue limit for R=0 about 81MPa, and the fatigue limit for R=0.3 about 93MPa. (3) The fatigue limit reduction rates by the fretting damage were about 52%(R=-1), 46%(R=0) and 38%(R=0.3) respectively. (4) The fatigue limit reduction rate decreased with stress ratio increase. In fretting bending test, as stress ratio increased, occurrence of initial oblique crack by fretting decreased or phased out, so that fracture surfaces were formed by plain fatigue crack occurrence, and such tendency was notable as stress amplitude increased. (5) Tire tracks and rubbed scars were observed in the fracture surface and contacted surface.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 1999년도 춘계 학술발표회 논문집 Proceedings of EESK Conference-Spring
• /
• pp.178-185
• /
• 1999

Minimum life-cycle cost helps to evaluate cost effectiveness of base-isolated bridges under specific condition. Life-cycle cost mainly consists of the initial construction cost and the expected damage cost. Damage cost estimation needs proper model of input ground motion failure probability evaluation method and limit states definition. We model the input ground motion as spectral density function compatible with the response spectra defined at each seismicity and site condition. Spectrum analysis and crossing theory is suitable for reseating calculation of failure probabilities in the process of cost minimization. Limit states of base-isolated bridges re defined for superstructure isolator and pier respectively The method is applied to both base-isolated bridges and conventional bridges under the same conditions to investigate cost effectiveness of base isolation in low and moderate seismic region. the results show that base-isolation of bridges are more effective in low and moderate seismic region and that the site effects on the economical efficiency may not be negligible in such a region.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 2006년도 학술발표회 논문집
• /
• pp.209-216
• /
• 2006

For evaluation of building performance, a nonlinear dynamic capacity of the building is a key parameter. In this study, an reinforced concrete special moment resisting frame building was chosen to study the process of determining the nonlinear dynamic capacity. The building, which was designed by IBC 2003 representing new codes, was composed of special moment resisting frames in the perimeter and internal frames inside the building. The capacity, which is inter-story drift capacity, consists of two categories, local and global collapses. Global collapse capacity was determined by incremental dynamic analysis. Local collapse capacity was determined by the same method except for utilizing damage index. In audition to this, it was also investigated that the effect of including internal frames designed by gravity load in the analysis. Results showed that the damage index is a useful tool for determining local collapse. Furthermore, including the internal frames with special frames in the analysis is very important in determining the capacity of a building so both must be considered at the same time.

• 방사선산업학회지
• /
• 제17권4호
• /
• pp.509-518
• /
• 2023

The Kori Unit 1 nuclear power plant, which is planned to be dismantled after permanent shutdown, is expected to generate a large amount of various types of radioactive waste during the dismantling process. For the disposal of Very-low-level waste, which is expected to account for the largest amount of generation, the Korea Radioactive waste Agency (KORAD) is in the process of detailed design to build a 3-phase landfill disposal facility in Gyeongju. In addition, a large container is being developed to efficiently dispose of metal and concrete waste, which are mainly generated as Very low-level waste of decommissioning. In this study, based on the design characteristics of the 3-phase landfill disposal facility and the large container under development, radiation exposure dose evaluation was performed considering the normal and accident scenarios of radiation workers during operation. The direct exposure dose evaluation of workers during normal operation was performed using the MCNP computer program, and the internal and external exposure dose evaluation due to damage to the decommissioning waste package during a drop accident was performed based on the evaluation method of ICRP. For the assumed scenario, the exposure dose of worker was calculated to determine whether the exposure dose standards in the domestic nuclear safety act were satisfied. As a result of the evaluation, it was confirmed that the result was quite low, and the result that satisfied the standard limit was confirmed, and the radiational disposal suitability for the 3-phase landfill disposal facility of the large container for dismantled radioactive waste, which is currently under development, was confirmed.

• Steel and Composite Structures
• /
• 제15권2호
• /
• pp.203-220
• /
• 2013

The study of the tensile strength of composite materials is far more complex than analysis of the properties of elasticity and plasticity. Indeed, during mechanical loading, micro-cracks in the matrix, the fibers break, debonding of the interfaces are created. The failure process of composites is of great diversity and cannot be described if even we know: the strength criterion of each individual component, the state of stress and strain in the material, the propagation phenomena cracks in the structure and nature of the interface between the matrix and the reinforcement. This information is only partially known and the obtained by the analysis of a stress limit beyond which there is destruction of the material is almost impossible. To partially process the issue, a solution lies in a mesoscopic approach of seeking a law to locate the ultimate strength of the material for a plane stress state. Tests on rectangular plates in bending PEEK/APC2 and T300/914 three were made and this in order to validate our approach, the calculation has been implemented in a nonlinear finite element code (Castem 2000), in order to make comparison with the numerical results. The results show good agreement between numerical simulation and the two materials; however, it would be interesting to consider other phenomena in the criterion.