• 한국자동차공학회논문집
• /
• 제24권2호
• /
• pp.225-231
• /
• 2016

A military vehicle is driven at different usage modes with the army application and servicing conditions. For practical durability validation, DT(Development Test) on a new military vehicle should be run up to the durability target kilometers on test courses in the specified proving ground. Driving velocities with test courses at the endurance mode of DT are established definitely. However, OT(Operational Test) and initial endurance test of production car can't be performed only in the DT courses due to the development period limit. Therefore, this paper focuses on the method to analyze the relative road damages between the endurance test in DT and other endurance test. Road load acquisition tests on KLTV(Korean Light Tactical Vehicle) were implemented at 15 driving modes in off-road and cross-country courses of two tests. Wheel accelerations were processed through band-pass filter, and then the main frequency and maximum power of the signals were computed by PSD analysis. Finally, using the proving ground optimization based on RDS(Relative Damage Spectrum) characterization, the damage factors between off-roads of test courses were determined.

• Corrosion Science and Technology
• /
• 제6권4호
• /
• pp.177-185
• /
• 2007

The purpose of this study is to evaluate freezing-thawing and surface scaling resistance in order to examine the frost durability of concrete in a chloride-inherent environment. The mixing design for this study is as follows: 3 water binder ratios of 0.37, 0.42, and 0.47; 2-ingredient type concrete (50% OPC concrete and 50% ground granulated blast-furnace slag), and 3-ingredient type concrete (50% OPC concrete, 15% fly ash, and 35% ground granulated blast-furnace slag). As found in this study, the decrease of durability was much more noticeable in combined deterioration through both salt damage and frost damage than in a single deterioration through either ofthese; when using blast-furnace slag in freezing-thawing seawater, the frost durability and surface deterioration resistance was evaluated as higher than when using OPC concrete. BF 50% concrete, especially, rather than BFS35%+FA15%, had a notable effect on resistance to chloride penetration and freezing/expansion. It has been confirmed that surface deterioration can be evaluated through a quantitative analysis of scaling, calculated from concrete's underwater weight and surface-dry weight as affected by the freezing-thawing of seawater.

• 한국재난정보학회 논문집
• /
• 제17권1호
• /
• pp.53-59
• /
• 2021

연구목적 및 방법: 본 논문은 지반구조물 계측센서의 내구연한 기준에 대한 분석적 연구로 국내 건설공사 발주기관의 건설 계측센서에 대한 내구연한 기준과 조달청의 건설계측 및 건설기계 관련 내용연수 기준을 분석하였다. 연구결과: 지반구조물에 설치되기 전 조달청에서 물품 자체로 구매하는 경사계와 변형률계 등의 내구연한 기준은 8년에서 10년을 제시하고 있다. 결론: 국내외 댐에 설치된 각종 계측센서의 신뢰성 비교를 통한 실제적인 내구연한 분석과 터널에 설치된 유지관리 계측센서의 경과연수에 대한 손망실율 등을 종합 검토한 결과 구조물이나 지반에 설치된 국내 간극수압계 및 토압계 등의 매립식 계측센서의 적정 내구연한은 5년에서 8년이 합리적인 것으로 판단된다.

• Earthquakes and Structures
• /
• 제7권2호
• /
• pp.179-199
• /
• 2014

The steel tube-reinforced concrete (ST-RC) composite column is a novel type of composite column, consisting of a steel tube embedded in reinforced concrete. The objective of this paper is to investigate the effect of cumulative damage on the seismic behavior of ST-RC columns through experimental testing. Six large-scale ST-RC column specimens were subjected to high axial forces and cyclic lateral loading. The specimens included two groups, where Group I had a higher amount of transverse reinforcement than Group II. The test results indicate that all specimens failed in a flexural mode, characterized by buckling and yielding of longitudinal rebars, failure of transverse rebars, compressive crushing of concrete, and steel tube buckling at the base of the columns. The number of loading cycles was found to have minimal effect on the strength capacity of the specimens. The number of loading cycles had limited effect on the deformation capacity for the Group I specimens, while an obvious effect on the deformation capacity for the Group II specimens was observed. The Group I specimen showed significantly larger deformation and energy dissipation capacities than the corresponding Group II specimen, for the case where the lateral cyclic loads were repeated ten cycles at each drift level. The ultimate displacement of the Group I specimen was 25% larger than that of the Group II counterpart, and the cumulative energy dissipated by the former was 2.8 times that of the latter. Based on the test results, recommendations are made for the amount of transverse reinforcement required in seismic design of ST-RC columns for ensuring adequate deformation capacity.

• 펄프종이기술
• /
• 제31권3호
• /
• pp.90-95
• /
• 1999

The durability of handmade paper prepared by potassium carbonate cooking of paper multiberry (Broussonetia Kazinoki Sieb).was investigated. The potassium carbonate paper before and after heat aging had better strength properties, breaking length and folding endurance than those of the soda paper, except of lower brightness .After 30 days of heat aging , these strength properties were still maintained . however, there was almost no difference in the infrared spectra and the crystallinities calculated by X-ray diffraction curves between the potassium carbonate paper and the soda a paper. The durability of the potassium carbonate paper was though to be due to decrease in the pulp damage caused by weak alkaline cooking condition. The results indicated that the paper prepared by the potassium carbonate cooling method could have better permanence than that prepared by the conventional soda cooking method.

• 한국자동차공학회논문집
• /
• 제21권6호
• /
• pp.166-174
• /
• 2013

This study investigates the strength durability on the results of structural and vibration analysis due to the shape of excavator wheel. As model 2 has the least stress by comparing three models with maximum equivalent stress, model 2 has most durability among three models at static analysis. Maximum equivalent stress is shown at the bottom part contacted with ground and this part on wheel is most affected by load in cases of all models. Safety factor can be decided with the value of 2.3 by considering the yield stress of this model. The range of maximum harmonic response frequencies becomes 6900 to 7000Hz. As model 2 has the least total deformation and equivalent stress at these critical frequencies, model 2 has the most durability at vibration analysis among three models. The structural and vibration analysis results in this study can be effectively utilized with the design of excavator wheel by investigating prevention and durability against its damage.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2007년도 춘계학술논문 발표대회
• /
• pp.147-150
• /
• 2007

As recent buildings often use low-quality concrete materials, are constructed defectively, and are put in extreme environmental conditions, many of them show the shortening of life resulting from the corrosion of reinforcing rods by salt damage, carbonization, freezing and thawing, cracking. This in turn raises the cost of repair and maintenance, so it is required to extend the life of structures through enhancing the durability of concrete. In response to the demand, researches on high-durability concrete are being made actively focused on the maximum water-cement ratio, the maximum unit quantity, the minimum cover thickness, the addition of mineral admixtures, etc. With this background, the present study examined the basic physical properties of concrete containing admixtures for enhancing the durability of concrete.

• 한국산학기술학회논문지
• /
• 제15권10호
• /
• pp.5974-5979
• /
• 2014

압입 방식으로서 경량화된 부품이 매우 균질한 정밀도로 생산이 되며 프레스의 기술이 향상되고 있다. 압입 방식으로 조립하였을 시 핀과 구멍사이에는 압축력에 의한 변형력이 발생되고 접촉면이 손상을 입는다. 따라서 본 연구에서는 CATIA 프로그램을 이용하여 3D 모델링하였으며, ANSYS 프로그램을 통하여 압입 접촉된 평면에서 손상평가를 하였다. 해석결과, 핀이 들어갈 때 PCB판에 작용하는 하중은 약 21.3N인 것으로 확인되었으며, PCB판이 Pin에서 빠져나올 때의 하중은 약 19.24N으로 나타났다. 또한 구조 해석결과, Pin 1이 본 연구 모델의 모든 부품들 중에서 가장 최대응력이 많이 발생하므로, 대표적으로 Pin 1의 최대 등가응력이 192.96MPa로 나타났다. 압입 접촉 손상 특성을 규명하고 본 연구결과를 실제의 압입 공정의 설계에 응용함으로서 그 파손을 방지하고 내구성을 평가할 수 있다고 사료된다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 춘계 학술발표회 제16권1호
• /
• pp.176-179
• /
• 2004

The latest concrete structure has showed that the deterioration of durability has been increased by the damage from salt, carbonization, freezing & thawing and the others. Therefore, the measures for the concrete which has deteriorated durability have been taken. Among them, it has been often used that surface treatment which cuts off the deterioration factors of durability by protecting the surface of concrete. This study was evaluated the surface improving agent for permeability, watertightness, air-permeability, chemical resistance and elution resistance.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 추계학술대회 초록집
• /
• pp.86.2-86.2
• /
• 2010

In order to improve polymer electrolyte membrane fuel cell (PEMFC) durability, the durability of membrane electrode assemblies (MEA), in which the electrochemical reactions actually occur, is one of the vital issues. Many articles have dealt with catalyst layer degradation of the durability-related factors on MEAs in relation to loss of catalyst surface area caused by agglomeration, dissolution, migration, formation of metal complexes and oxides, and/or instability of the carbon support. Degradation of catalyst layer during long-term operation includes cracking or delamination of the layer which result either from change in the catalyst microstructure or loss of electronic or ionic contact with the active surface, can result in apparent activity loss in the catalyst layer. Membrane degradation of the durability-related factors on MEAs can be caused by mechanical or thermal stress resulting in formation of pinholes and tears and/or by chemical attack of hydrogen peroxide radicals formed during the electrochemical reactions. All of these effects, the mechanical damage of membrane and degradation of catalyst layers are more facilitated by uneven stress or improper MEA fabrication process. In order to improve the PEMFC durability, therefore, it is most important to minimize the uneven stress or improper MEA fabrication process in the course of the fabrication of MEA. We analyzed the effects of the MEA fabrication condition on the PEMFC durability with MEA produced using CCM (catalyst coated membrane) method. This paper also investigated the effects of MEA fabrication condition on the PEMFC durability by adding additional treatment process, hot pressing and pressing, on the MEA produced using CCM method.