• 한국신재생에너지학회:학술대회논문집
• /
• 2005.11a
• /
• pp.680-683
• /
• 2005

This paper proposes a simple MPPT control scheme of a Current-Control-Loop Error system Based that can be obtains a lot of advantage to compare with another digital control method, P&O and IncCond algorithm that is applied mostly a PV system. An existent method is needed an expensive processor such as DSP that calculated to change the measure power of a using current and voltage sensor at the once. Therefore, it is applied a small home power generation system that required many expenses. But, a proposed method is easy to solve the cost reduction and power unbalance problems that it is used by control scheme to limit error of a current control of common sensor. This proposed algorithm had verified through a simulation and an experiment on battery charger using PIC that is the microprocessor of a low price.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.491-494
• /
• 1994

The 3-level inverter is applied to the induction motor drive as the voltage type inverter for large poller one. This inverter divides the DC link voltage into the two parts and it is supplied to the inverter. The 3-level inverter can reduces the voltage between the each devices, and get more sinusoidal current waveform. This paper presents the new PWM method which can reduces the harmonics. The modulation at the inverter side is implemented using a DSP microprocessor.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.620-623
• /
• 2000

A very simple control approach using neural network for the robust position control of a Permanent Magnet Synchronous Motor(PMSM) is presented The linear quadratic controller plus feedforward neural network is employed to obtain the robust PMSM system approximately linearized using field-orientation method for an AC servo. The neural network is trained in on-line phases and this neural network is composed by a fedforward recall and error back-propagation training. Since the total number of nodes are only eight this system can be easily realized by the general microprocessor. During the normal operation the input-output response is sampled and the weighting value is trained multi-times by error back-propagation method at each sample period to accommodate the possible variations in the parameters or load torque. And the state space analysis is performed to obtain the state feedback gains systematically. IN addition the robustness is also obtained without affecting overall system response. This method is realized by a floating-point Digital Singal Processor DS1102 Board (TMS320C31) The basic DSP software is used to write C program which is compiled by using ANSI-C style function prototypes.

• Smart Structures and Systems
• /
• v.3 no.1
• /
• pp.69-88
• /
• 2007

In this study, Field-Programmable Gate Arrays (FPGAs) are investigated as a practical solution to the challenge of designing an optimal platform for implementing algorithms in a wireless sensing unit for structuralhealth monitoring. Inherent advantages, such as tremendous processing power, coupled with reconfigurable and flexible architecture render FPGAs a prime candidate for the processing core in an optimal wireless sensor unit, especially when handling Digital Signal Processing (DSP) and system identification algorithms. This paper presents an effort to create a proof-of-concept unit, wherein an off-the-shelf FPGA development board, available at a price comparable to a microprocessor development board, was adopted. Data processing functions, including windowing, Fast Fourier Transform (FFT), and peak detection, were implemented in the FPGA using a Matlab Simulink-based high-level abstraction tool rather than hardware descriptive language. Simulations and laboratory tests were carried out to validate the design.

• Proceedings of the KIPE Conference
• /
• 2004.07a
• /
• pp.151-154
• /
• 2004

To use the SLIM for servo system, the exact account of thrust about the initial speed is needed, but analyzing by equivalent circuit analyzing methode such as rotary induction motor, the error occurs because of the end effect. So, we applied the equivalent circuit considering the end effect of SLIM in this paper. The current control system is advanced the space vector pulse width modulation by using high arithmetic performance microprocessor such as DSP. In this paper, we use the dynamic characteristic analyzing methode that can calculate efficiently the end effect by using equivalent circuit methode in the operating SLIM system modeling and examine the output characteristics of SVPWM with PI controller.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.3 no.3
• /
• pp.240-245
• /
• 1998

This paper presents an improved sliding mode controller design for induction motor. In place of the discontinuous control inputs, continuous inputs are proposed in order to remove the undesirable chattering phenomena, which represent major drawbacks of the sliding mode controller. The design strategy is illustrated with a microprocessor based implementation for the velocity control of an induction motor. An induction motor is operated under sling mode control such that the motor angular velocity follows a predetermined trajectory. The experimental results confirm the validity of the proposed method.

• Journal of Institute of Control, Robotics and Systems
• /
• v.12 no.7
• /
• pp.637-643
• /
• 2006

Generally, the tracking performance of optical disk drive(ODD) system can be improved using a disturbance observer(DOB). However, a DOB is not easily applied in an ODD system because an additional microprocessor, such as a digital signal processor(DSP), is needed. This paper shows how a DOB system can be replaced by the error-based modified disturbance observer(EM-DOB) when two mathematical conditions are satisfied. Due to the simplified structure of EM-DOB, the algorithm is easily implemented as an analog circuit, which is suitable for the ODD servo system. Additionally, in these algorithms, disturbances rejection performances can be tuned as Q filter parameters. Similar to a DOB system, three design guidelines of a Q filter can be applied. Experimental results of DOB and EM-DOB are evaluated under forced disturbances.

• Proceedings of the KIPE Conference
• /
• 2002.07a
• /
• pp.343-346
• /
• 2002

In recent, complex SVPWM (Space Vector PWM) algorithm can be easily implemented by high performance microprocessor and DSP. Various SVPWM techniques are widely studied due to the advantages of low harmonic distortion and high use ratio of D.C. link voltage. Most of various studies for improving of VS-PWM inverter performance are concentrated about switching pattern and zero pulse pattern split algorithms. However, dc link voltage that is determined at rated load and speed conditions is not proper in the low speed and under rated load. In this paper, analysis of current ripple with digitally implemented SVPWM inverter is introduced according to link voltage. The optimal link voltage in the designed inverter system and load condition is provided in order to suppress output voltage error and current ripple. As remaining the effective voltage vector interval per sampling period sufficiently, additional voltage error and current ripple are suppressed. The proposed algorithm is verified through digital simulation and experimental results.

• Journal of Power Electronics
• /
• v.12 no.3
• /
• pp.503-508
• /
• 2012

Tracking the Maximum Power Point (MPP) of a photovoltaic (PV) array is usually an essential part of a PV system. The problem addressed by Maximum Power Point Tracking (MPPT) techniques is to find the voltage $V_{MPP}$ or current $I_{MPP}$ at which a PV array should operate to generate the maximum power output $P_{MPP}$ under a given temperature and irradiance. MPPT control methods such as the perturb and observe method and the incremental conductance method require a microprocessor or DSP to determine if the duty cycle should be increased or not. This paper proposes a simple and fast analog MPPT method. The proposed control scheme tracks the MPP very quickly and its hardware implementation is simple when compared with the conventional techniques. The new algorithm can successfully track the MPP even in the case of rapidly changing atmospheric conditions. In addition, it has higher efficiency than ordinary algorithms.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.265-269
• /
• 1994

The switching dead time avoiding a bridge leg short circuit in PWM voltage source inverter produces distortions of the controlling inverter output performance such as current waveform, voltage vector, and torque. In this paper, the influence of dead time is investigated. The on-line space voltage vector modulation method is used for current controller. It is possible to compensate dead time by space voltage vector modulation which generates additional pulse compensating voltage distortion caused by dead time. In addition, narrow pulse which is generally neglected can be compensated. All the algorithms, including field-oriented control are performed by one chip microprocessor 80C196MC and DSP TMS320C31. Experimental results probe that the proposed scheme provides a good inverter output performance.