• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.19 no.8
• /
• pp.109-115
• /
• 2005

This paper addresses the CAN based networked intelligent multi-motor control system using DSP2812 microprocessor. CAN built in DSP2812 microprocessor is used to control and monitor the multi-motor system with the inverter driving system CAN network implementation schemes and the algorithm for multi-motor control and monitoring is also developed. We configure the multi-motor control experimental system to verify the proposed algerian and the reliability of CAN networks system in the various operation of two induction motors. The experimental results show that CAN based networked intelligent multi-motor control system using DSP2812 microprocessor can carry out the real-time network based control in various speed range and the position control of induction motors.

• Proceedings of the IEEK Conference
• /
• 1999.06a
• /
• pp.257-260
• /
• 1999

We have designed a 32-bit RISC microprocessor with 16/32-bit fixed-point DSP functionality. This processor, called YRD-5, combines both general-purpose microprocessor and digital signal processor (DSP) functionality using the reduced instruction set computer (RISC) design principles. It has functional units for arithmetic operation, digital signal processing (DSP) and memory access. They operate in parallel in order to remove stall cycles after DSP and load/store instructions with one or more issue latency cycles. High performance was achieved with these parallel functional units while adopting a sophisticated 5-stage pipeline structure and an improved DSP unit.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2005.11a
• /
• pp.81-87
• /
• 2005

This paper addresses the CAN based networked intelligent multi-motor control system using DSP2812 microprocessor. CAN built in DSP2812 microprocessor is used to control and monitor the multi-motor system with the inverter driving system. CAN network implementation schemes and the algorithm for multi-motor control and monitoring is also developed. We configure the multi-motor control experimental system to verify the proposed algorithm and the reliability of CAN networks system in the various operation of two induction motors. The experimental results show that CAN based networked intelligent multi-motor control system using DSP2812 microprocessor can carry out the real-time network based control in various speed range and the position control of induction motors.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.7 no.4
• /
• pp.229-234
• /
• 2007

In this paper, we present an efficient instruction set architecture using vector register file hardware to accelerate operation of general matrix-vector operations in DSP microprocessor. The technique enables in-situ row-access as well as column access to the register files. It can reduce the number of memory access significantly. The technique is especially useful for block-based video signal processing kernels such as FFT/IFFT, DCT/IDCT, and two-dimensional filtering. We have applied the new instruction set architecture to in-loop deblocking filter processing in H.264 decoder. Performance comparisons show that the required load/store operations for the in-loop deblocking filter can be reduced about 42%. The architecture would improve the processing speed, and code density in DSP microprocessor especially for video signal processing substantially.

• International Journal of Precision Engineering and Manufacturing
• /
• v.4 no.1
• /
• pp.9-14
• /
• 2003

In this study we suggest real-time simulator that could describe rent system without ordinary DSP card. This simulator is composed of 80196kc-16bit ordinary microprocessor, which is widely used up to now and personal computer. DSP card that has calculated complex numerical equation is replaced by personal computer and 80196kc generates control signals independently out of the personal computer. In all process personal computer is synchronized with one-board microprocessor (80196kc) within sampling time in the closed loop system. This makes it possible to be described in hydraulic servo system in real time.

• Proceedings of the KIPE Conference
• /
• 1999.07a
• /
• pp.618-621
• /
• 1999

With the advent of the high-speed microprocessor and DSP, the possibility of executing a control strategy in digital domain has become a reality. By the use of the DSP and microprocessor controller, many high power drive system may be enhanced resulting in the improved robustness to EMI, the ability to communicate the operating conditions and the ease of adjusting the control parameters. But, the digital controller using DSP or microprocessor is not applied in the high frequency switching power supplies, especially full bridge DC/DC converter. So, this paper presents the method and realization of designing a digital-to-phase shift PWM circuit for full digital controlled full bridge DC/DC converter with zero voltage switching. The operating principles, simulation and experimental results will be presented.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.45-48
• /
• 2000

By the use of he DSP and microprocessor controller many high power converter such as especially inverter and motor drive system may be enhanced resulting in the improved robustness of EMI the ability to communicate the operating conditions and the ease of adjusting the control parameters. However the digital controller using DSP or microprocessor has not been applied in the high frequency switching power supplies especially in full bridge dc/dc converters. this paper presents a promising solution to the dc bias control problem of high frequency transformer in high power full bridge converter.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.442-446
• /
• 1998

With the advent of the high-speed microprocessor and DSP, the possibility of executing a control strategy in digital domain has become a reality. By the use of the DSP and microprocessor controller, many high power converters such as especially inverter and motor drive system may be enhanced resulting in the improved robustness to EMI, the ability to communicate the operating conditions and the ease of adjusting the control parameters. But, the digital controller using DSP or microprocessor is not applied in the high frequency switching power supplies, especially full bridge dc/dc converter. So, this paper presents the method and realization of designing a digital-to-phase shift PWM circuit for full digital controlled phase-shifted full bridge dc/dc converter with zero voltage switching. The operating principles, simulation and experimental results will be presented.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.62 no.3
• /
• pp.133-138
• /
• 2013

A large generator is an important role in transferring an electric power to power system. The IEDs of large generator often use microprocessor technology to obtain a digital relay system with a wide range of measuring, protection, control, monitoring, and communication functions. However, all generator protection and control systems in Korea imported from abroad and are being operated. In order to reduce the large expense and improve the reliable operation, development of generator protection and control system by domestic technology is required. This paper deals with the design of the IED of generator protection panel for development of generator protection and control system. The major emphasis of the paper will be on the description of hardware and signal processing test results and measurement accuracy of the prototype IED. By developing of generator IED based on DSP and microprocessor, replacement of the generator protection panel imports are expected to be effective.

• Journal of Advanced Marine Engineering and Technology
• /
• v.20 no.3
• /
• pp.121-130
• /
• 1996

Permanent magnet synchronous motor is widely used in industrial drive applications due to high efficiency, high power ratio, and easy maintenance. Position and speed detectors required in this motor increase the drive cost, and reduce the application range. Some papers present the speed control without position and speed detectors using DSP characterized by high processing performance. However, DSP increases the cost, and makes the inplementation difficult. This study has performed the speed control without position and speed detector by means of the microprocessor system which can be easily accessed. The results of simulation and experiment showed comparatively good dynamics in spite of the sensorless system.