• 전기학회논문지P
• /
• 제65권1호
• /
• pp.18-24
• /
• 2016

In order to service restoration and enhance power system reliability, a number of impedance based fault location algorithms have been developed for fault locating in a transmission line. This paper presents an advanced impedance-based fault location algorithms in a two-ended sources transmission line to reduce the DC offset error effects. This fault location algorithm uses of the GPS time synchronized voltage and current signals from the local and remote terminal. The algorithm uses an advanced DC offset removal filter. A series of test results using ATPdraw simulation data show the performance effectiveness of the proposed algorithm. The proposed algorithm is valid for a two-end sources transmission network.

• 한국위성정보통신학회논문지
• /
• 제10권1호
• /
• pp.88-91
• /
• 2015

무선전력전송은 별도의 전송선로 없이 에너지를 전달하는 기법으로, 기존의 무선통신에서의 신호가 아닌 에너지 자체의 전달을 목적으로 한다. 원거리 마이크로파 전력송수신기는 RF 발진회로, 고이득 안테나, 정류회로 등으로 구성되는데, 상용화를 위해서는 저렴한 고출력 발진회로 및 설치가 용이한 안테나 설계의 어려움이 해결되어야할 과제이다. 이것 때문에 발진회로와 개별 안테나가 각각 연결된 에너이로 구성된 시스템 채택이 예상된다. 본 고찰는 무선전력 송수신기의 전력계통의 영향 분석 일환으로 수행하였다.

• Journal of Power Electronics
• /
• 제13권5호
• /
• pp.737-745
• /
• 2013

Offshore wind farms are rapidly growing owing to their comparatively more stable wind conditions than onshore and land-based wind farms. The power capacity of offshore wind turbines has been increased to 5MW in order to capture a larger amount of wind energy, which results in an increase of each component's size. Furthermore, the weight of the marine turbine components installed in the nacelle directly influences the total mechanical design, as well as the operation and maintenance (O&M) costs. A reduction in the weight of the nacelle allows for cost-effective tower and foundation structures. On the other hand, longer transmission distances from an offshore wind turbine to the load leads to higher energy losses. In this regard, DC transmission is more useful than AC transmission in terms of efficiency because no reactive power is generated/consumed by DC transmission cables. This paper describes some of the challenges and difficulties faced in designing high-power-density power conversion systems (HPDPCSs) for offshore wind turbines. A new approach for high gain/high voltage systems is introduced using transformerless power conversion technologies. Finally, the proposed converter is evaluated in terms of step-up conversion ratio, device number, modulation, and costs.

• 한국전자파학회논문지
• /
• 제24권6호
• /
• pp.613-622
• /
• 2013

본 논문에서는 ISM 13.56 MHz 대역 무선 전력 전송을 위한 인덕티브 클램핑 class-E 전력증폭기를 설계 및 실험하여 특성을 분석하였다. 구현된 전력증폭기는 수신 안테나가 회전체에 붙는 경우와 같이 송수신 안테나 간의 정합 상태가 변화하는 시스템에서 부정합 상태에서 전력증폭기에 공급되는 전류를 줄여 트랜지스터를 손상시키지 않고 안정적으로 동작하도록 하는 인덕티브 클램핑 방식으로 설계되었으며, 정합 회로를 이용하여 기존의 class-E 전력증폭기보다 고조파 성분에 대한 Filtering 특성을 개선하였다. 구현된 전력증폭기의 입력 주파수는 13.56 MHz, 입력 전력 25 dBm, 동작 전압 DC 28 V에서 측정한 결과, 출력 전력은 43 dBm, 기본 주파수 성분과 2차 고조파 신호 간의 출력 전력 차이 55 dBc 이상, 소모 전류 830 mA으로 전력부가 효율(power added efficiency)은 85 %로 높게 측정됐다. 마지막으로, 수신 안테나를 회전체에 부착하고 구현된 전력증폭기로 송수신 안테나로 전력을 송출하는 실험을 진행하였으며, 송신 안테나의 부정합 상태에는 소모 전류가 420 mA까지 줄어들어 트랜지스터가 손상되지 않는 것을 확인하였다.

• Journal of Power Electronics
• /
• 제11권2호
• /
• pp.156-162
• /
• 2011

The control loop time delay caused by sampling, the zero-order-holder effect and calculations is inevitable in the digital control of dc-dc switching converters. The time delay will limit the bandwidth of the control loop and therefore degrade the transient performance of digital systems. In this paper, the quantization time delay effects with different time delay values based on a generic second-order system are analyzed. The conclusion that the bandwidth of digital control is reduced by about 20% with a one cycle delay and by 50% with two cycles of delay in comparison with no time delay is obtained. To compensate the time delay and to increase the control loop bandwidth, a duty ratio predictive control scheme based on linear extrapolation is proposed. The compensation effect and a comparison of the load variation transient response characteristics with analogy control, conventional digital control and duty ratio predictive control with different time delay values are performed on a point-of-load Buck converter by simulations and experiments. It is shown that, using the proposed technique, the control loop bandwidth can be increased by 50% for a one cycle delay and 48.2% for two cycles of delay when compared to conventional digital control. Simulations and experimental results prove the validity of the conclusion of the quantization effects of the time delay and the proposed control scheme.

• 전기학회논문지
• /
• 제57권1호
• /
• pp.52-57
• /
• 2008

In the transformer that is used for the contactless power transmission system, the primary and secondary sides are separated structurally unlike general transformers. When the contactless transformer is built, it forms relatively bigger air gap than the general transformer. Thus it is difficult to transfer energy from the primary side input to the secondary side output with high power efficiently because of low coupling coefficient. This paper proposes a contactless transformer using the rectangular type core that maintains high coupling coefficient even when it has relatively large air gap. The performance characteristics of the proposed transformer are compared with the transformer using general EE core to the air gap variation. The proposed contactless system using rectangular type core and dc-dc full bridge converter, and the system using EE core type and dc-dc full bridge converter are respectively implemented and their performance characteristics are verified by the simulation and experiment.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.427-428
• /
• 2008

We have studied design and application about an self generation equipment for underground power transmission cable. The split CT(Current Transformer), which has the applicable underground power transmission cable, was manufactured through electromagnetic simulation of magnetic core. And manufactured the AC-DC converter that supplied stable DC power for PLC modem when current of power line has more than 150A. An self generation equipment using the CT and AC-DC converter get into operation the PLC modem consistently. As a result, the underground power transmission cable was showed the application possibility through the stable communication and network characteristics.

• 조명전기설비학회논문지
• /
• 제29권2호
• /
• pp.97-103
• /
• 2015

This paper introduces two on-going projects for DC high temperature superconducting (HTS) cable systems in South Korea. This study proposes the application of DC HTS cable systems to enhance power transfer limits of a grid-connected offshore wind farm. In order to develop the superconducting DC transmission system model based on HTS power cables, the maximum transfer limits from offshore wind farm are estimated and the system marginal price (SMP) calculated through a Two-Step Power Transfer (TSPT) model based on PV analysis and DC-optimal power flow. The proposed TSPT model will be applied to 2022 KEPCO systems with offshore wind farms.

• 전력전자학회논문지
• /
• 제17권3호
• /
• pp.252-258
• /
• 2012

This paper studies the power line communication method with splitting of power transmission interval in the small DC power system using pulse width modulation. The method divides the entire interval for transmitting power and data into a power transmission interval where power is supplied to a load and a data transmission interval where power from the power supply to the load is disconnected. The circuit is designed for the implementation to separate the power line from the power supply and load. The results of tests show the feasibility of the proposed power line communication method.

• 전기학회논문지
• /
• 제65권6호
• /
• pp.955-961
• /
• 2016

Fault location estimation is an important element for rapid recovery of power system when fault occur in transmission line. In order to calculate line impedance, most of fault location algorithm uses by measuring relaying waveform using DFT. So if there is a calculation error due to the influence of phasor by DC offset component, due to large vibration by line impedance computation, abnormal and non-operation of fault locator can be issue. It is very important to implement the robust fault location algorithm that is not affected by DC offset component. This paper describes an enhanced fault location algorithm based on the DC offset elimination filter to minimize the effects of DC offset on a long transmission line. The proposed DC offset elimination filter has not need any erstwhile information. The phase angle delay of the proposed DC offset filter did not occurred and the gain error was not found. The enhanced fault location algorithm uses DFT filter as well as the proposed DC offset filter. The behavior of the proposed fault location algorithm using off-line simulation has been verified by data about several fault conditions generated by the ATP simulation program.