• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.2
• /
• pp.120-124
• /
• 2003

This paper describes a MEMS-based micro-fluxgate magnetic sensing element using Ni$\_$0.8/Fe$\_$0.2/ film formed by electroplating. The micro-fluxgate magnetic sensor composed of a thin film magnetic core and micro-structure solenoids for the pick-up and the excitation coils, is developed by using MEMS technologies in order to take advantage of low-cost, small size and lower power consumption in the fabrication. A copper with 20${\mu}$m width and 3${\mu}$m thickness is electroplated on Cr (300${\AA}$) / Au (1500${\AA}$) films for the pick-up (42turn) and the excitation (24turn) coils. In order to improve the sensitivity of the sensing element, we designed the magnetic core into a rectangular-ring shape to reduce the magnetic flux leakage. An electroplated permalloy film with the thickness of 3${\mu}$m is obtained under 2000 gauss to induce magnetic anisotropy. The magnetic core has the high DC effective permeability of ~1,100 and coercive field of ~0.1 Oe. The fabricated sensing element using rectangular-ring shaped magnetic film has the sensitivity of about 150 V/T at the excitation frequency of 2 MHz and the excitation voltage of 4.4 V$\_$p p/. The power consumption is estimated to be 50mW.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.40-41
• /
• 2006

In this work, we developed the 0-3 type piezoelectric composite to incorporate the advantages of both ceramic and polymer. The PVDF-PZT composites were fabricated with various mixing ratio by 3-roll mi11 mixer. The composite solutions were coated on ITO bottom-electrode deposited on PET (polyethylene terephthalate) polymer film by the conventional screen-printing method. After depositing the top-electrode of silver-paste, 4kV/mm of DC field was applied at $120^{\circ}C$ for 30min to poling the 0-3 composite film. The value of $d_{33}$ was increased as the PZT weight percent was increases. But the $g_{33}$ value showed the maximum at 65 wt% of PZT powder.

• Mycobiology
• /
• v.45 no.4
• /
• pp.409-420
• /
• 2017

Foliar sprays of three plant resistance inducers, including chitosan (CH), potassium sorbate (PS) ($C_6H_7kO_2$), and potassium bicarbonates (PB) ($KHCO_3$), were used for resistance inducing against Erysiphe cichoracearum DC (powdery mildew) infecting okra plants. Experiments under green house and field conditions showed that, the powdery mildew disease severity was significantly reduced with all tested treatments of CH, PS, and PB in comparison with untreated control. CH at 0.5% and 0.75% (w/v) plus PS at 1.0% and 2.0% and/or PB at 2.0% or 3.0% recorded as the most effective treatments. Moreover, the highest values of vegetative studies and yield were observed with such treatments. CH and potassium salts treatments reflected many compounds of defense singles which leading to the activation power defense system in okra plant. The highest records of reduction in powdery mildew were accompanied with increasing in total phenolic, protein content and increased the activity of polyphenol oxidase, peroxidase, chitinase, and ${\beta}$-1,3-glucanase in okra plants. Meanwhile, single treatments of CH, PS, and PB at high concentration (0.75%, 2.0%, and/or 3.0%) caused considerable effects. Therefore, application of CH and potassium salts as natural and chemical inducers by foliar methods can be used to control of powdery mildew disease at early stages of growth and led to a maximum fruit yield in okra plants.

• Korean Journal of Optics and Photonics
• /
• v.9 no.4
• /
• pp.215-220
• /
• 1998

We proposed an in situ measurement set-up and technique to measure the various electro-optic(E-O) properties of the E-O polymer. Using the proposed measurement set-up, the electro-optic effect and birefringence of unpoled side-chain E-O polymer induced by the strong dc and ac electric field were observed. The dependence of the E-O coefficients on the various poling conditions were measured with real time. To evaluate the thermal stability of the poled polymer the relaxation of the E-O effect was measured and the result was compared with well known polymer materials. The proposed measurement reduces the number of experimental steps and saves measurement time.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.11
• /
• pp.186-194
• /
• 2004

In this research, microfabrication technique using localized electrochemical deposition (LECD) with ultra short pulses is presented. Electric field is localized near the tool tip end region by applying a few hundreds of nano second pulses. Pt-Ir tip is used as a counter electrode and copper is deposited on the copper substrate in 0.5 M CuSO$_4$ and 0.5 M H$_2$SO$_4$ electrolyte. The effectiveness of this technique is verified by comparison with LECD using DC voltage. The deposition characteristics such as size, shape, surface, and structural density according to applied voltage and pulse duration are investigated. The proper condition is selected from the results of the experiments. Micro columns less than 10 $\mu$m in diameter are fabricated using this technique. The real 3D micro structures such as micro pattern and micro spring can be fabricated by this method. It is suggested that presented method can be used as an easy and inexpensive method for fabrication of microstructure with complex shape.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11a
• /
• pp.731-734
• /
• 2005

Generally, characteristics of electromechanical actuators are coupled with the mechanical and the electrical properties. Important mechanical parameters of these actuators are the achievable force and displacement in the presence of electric field. These mechanical parameters are related to the stress and strain of the materials and the actuator geometry. This paper presents how to measure the blocked force by using the micro-balance. The blocked force is defined as the force produced by the transducer under an applied voltage when the tip is constrained to zero motion. Also, a theoretical force by using the cantilever beam model is calculated under elastic domain. From the sample of 4 cm $\times$ 1 cm $\times$ 20 $\mu$m, the blocked farce measured from the equipment is 20.3 $\mu$N at 8 V$_{DC}$. By comparing it with the theoretical value, 24.9 $\mu$N, the blocked force measurement is acceptable. The furce measurement is also investigated with different AC electric fields and the frequency.

• Journal of the Korean institute of surface engineering
• /
• v.48 no.5
• /
• pp.205-210
• /
• 2015

NbN coatings were prepared by ICP (inductively coupled plasma) assisted magnetron sputtering from a Nb metal target in $Ar+N_2$ atmosphere at various ICP powers. Effect of ICP on the microstructure, crystalline structure and mechanical properties of NbN coatings was investigated by field emission electron microscopy, X-ray diffraction, atomic force microscopy and nanoindentation measurements. The results show that ICP power has a significant influence on coating microstructure, structure and mechanical properties of NbN coatings. With the increasing of ICP power, coating microstructure evolves from the columnar structure of DC process to a highly dense one. Crystalline structure of NbN coatings were changed from cubic ${\delta}$-NbN to hexagonal ${\beta}-Nb_2N$ with increase of ICP power. The maximum nano hardness of 25.4 GPa with Ra roughness of 0.5 nm was obtained from the NbN coating sputtered at ICP power of 200 W.

• Journal of Power Electronics
• /
• v.19 no.6
• /
• pp.1536-1543
• /
• 2019

This paper presents an improved torque predictive control (TPC) for permanent magnet synchronous motors (PMSMs) using an indirect matrix converter (IMC). The IMC has characteristics such as a high power density and sinusoidal waveforms of the input-output currents. Additionally, this configuration does not have any DC-link capacitors. Due to these advantages of the IMC, it is used in various application field such as electric vehicles and railway cars. Recently, research on various torque control methods for PMSM drives using an IMC is being actively pursued. In this paper, an improved TPC method for PMSM drives using an IMC is proposed. In the improved TPC method, the magnitudes of the voltage vectors applied to control the torque and flux of the PMSM are adjusted depending on the PMSM torque control such as the steady state and transient response. Therefore, it is able to reduce the ripples of the output current and torque in the low-speed and high-speed load ranges. Additionally, the improved TPC can improve the dynamic torque response when compared with the conventional TPC. The effectiveness of the improved TPC method is verified by experimental results.

• Korean Journal of Materials Research
• /
• v.28 no.11
• /
• pp.611-614
• /
• 2018

Laminate composites composed of $0.95Pb(Zr_{0.52}Ti_{0.48})O_3-0.05Pb(Mn_{1/3}Sb_{2/3})O_3$ piezoelectric ceramic and Fe-Si-B based magnetostrictive amorphous alloy are fabricated, and the effect of control of the areal dimensions and the thickness of the piezoelectric layer on the magnetoelectric(ME) properties of the laminate composites is studied. As the aspect ratio of the piezoelectric layer and the magnetostrictive layer increases, the maximum value of the ME voltage coefficient(${\alpha}_{ME}$) increases and the intensity of the DC magnetic field at which the maximum ${\alpha}_{ME}$ value appears decreases. Moreover, as the thickness of the piezoelectric layer decreases, ${\alpha}_{ME}$ tends to increase. The ME composites exhibit ${\alpha}_{ME}$ values higher than $1Vcm^{-1}Oe^{-1}$ even at the non-resonance frequency of 1 kHz. This study shows that, apart from the inherent characteristics of the piezoelectric composition, small thicknesses and high aspect ratios of the piezoelectric layer are important dimensional determinants for achieving high ME performance of the piezoelectric-magnetostrictive laminate composite.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.5
• /
• pp.382-386
• /
• 2019

The alignment characteristics of liquid crystal (LC) molecules on a solution-derived lanthanum zinc oxide (LZO) film under ion-beam irradiation were demonstrated. Using the solution process, an LZO film was fabricated on the glass substrate and cured at $100^{\circ}C$. Afterwards, ion-beam irradiation was performed following the LC alignment method. Using this film, an LC cell was fabricated and the characteristics of the LC alignment were verified. Cross polarizing microscopy and the crystal rotation method were used to investigate the alignment state of the LC molecules on the LZO films. Furthermore, field emission scanning electron microscopy and X-ray photoelectron spectroscopy were used to explore the effect of the ion-beam irradiation on the LZO film. Through these, it was confirmed that the ion-beam irradiation induced surface modification, which demonstrated anisotropic physical and chemical surface characteristics. Due to this, uniform LC alignment was achieved. Finally, the residual DC and anchoring energy of the LC cell based on the LZO films were measured using a capacitance-voltage curve.