• 한국태양에너지학회 논문집
• /
• 제32권4호
• /
• pp.43-50
• /
• 2012

Metal-metal oxide (M-M oxide) cermet solar selective coatings with a double cermet layer film structure were deposited on the Al-deposited glass substrate by using a directed current (DC) magnetron sputtering technology. M oxide (CrO and ZrO) was used as the ceramic component in the cermets, and Cr and Zr used as the metallic components. In addition, black Cr (Cr-$Cr_2O_3$ cermet) solar selective coatings were deposited on the Ni-plated Cu substrate by using a electroplating method for comparison. The thermal stability tests were carried out for performance evaluation of solar coatings. Reflectance measurements were used to evaluate both solar absorptance(${\alpha}$) and thermal emittance (${\epsilon}$) of the solar coatings before and after thermal testing by using a spectrometer. Optical properties of optimized cermet solar coatings were ${\alpha}{\simeq}0.94-0.96$ and ${\epsilon}{\simeq}0.1$ ($100^{\circ}C$). The results of thermal stability test of M-M oxide solar coatings showed that the Cr-CrO cermet solar selective coatings were more stable than the Zr-ZrO cermet selective coatings at temperature of both $400^{\circ}C$ in air and $450^{\circ}C$ in vacuum. The black Cr solar selective coatings were degraded in air at temperature of $400^{\circ}C$. The main optical degradation modes of these coatings were diffusion of metal atoms, and oxidation.

• 동력기계공학회지
• /
• 제22권1호
• /
• pp.41-47
• /
• 2018

This paper analyzes the output characteristics of a self excited induction generator with isolated mode according to change of its speeds and loads for building a hybrid electric propulsion system in special purpose ships by using power take off. The induction generators are being considered as an alternative choice to the well-developed generators because of their lower unit cost, inherent ruggedness, operational and maintenance simplicity. However, the generator working by stand alone has a few problems that the reactive power is required to establish the air gap magnetic flux, and the induced voltage and magnetizing current fluctuate when the load is varied. In spite of its advantages, basic design data of the capacitor bank and behaviors of the output characteristics of the generator are not sufficient for the system. Based on the operating condition(speed range of main engine) of the target boat, a reduced experimental equipment system was constructed to analyze the output characteristics of the SEIG. And a suitable capacitor bank of a stand-alone generator and its output characteristics under various loads was investigated in detail through these experiments. According to the experimental result, it was confirmed that the capacitor bank should be $70{\mu}F{\sim}100{\mu}F$, and the proper SEIG induced voltage should be DC 80 V ~ 250 V in order to storage electrical energy into a battery.

• 한국재료학회지
• /
• 제8권12호
• /
• pp.1152-1157
• /
• 1998

금속 타겟들을 이용한 반응성 스퍼터링법으로 $460~540^{\circ}C$범위에서 $Pt/Ti/SiO_2$/Si 기판위에 PZT 박막을 증착하였다. Perovskite상의 핵형성을 위해 Pb 휘발이 적은 저온($480^{\circ}C$)에서 짧은 시간 동안 PZT 박막을 증착한 후 Pb가 PBT 박막내에 과잉으로 함유되는 것을 억제하기 위하여 증착 온도를 증가시켜 박막을 증착하는 2단계 증착법을 사용한 결과 54$0^{\circ}C$의 고온에서도 perovskite 단일상과 화학양론비에 가까운 조성을 얻을 수 있었다. 2단계 증착법으로 제조된 PZT 박막은 우수한 전기적 특성을 나타내었으며 후속 RTA 처리로 더욱 특성을 향상시킬 수 있었는데 $17\mu$C/$\textrm{cm}^2$의 잔류분극, 45kv/cm의 coercive field, 그러고 -500kv/cm의 높은 전기장에서도 $10^{-4}$ A/$\textrm{cm}^2$의 양호한 누설전류 특성을 나타내었다.

• 한국자기학회지
• /
• 제10권5호
• /
• pp.250-255
• /
• 2000

본 연구에서는 double rectangular spiral형 공심 인덕터를 유사 LIGA공정으로, F $e_{86.7}$Z $r_{3.3}$ $B_{4}$A $g_{6}$ 자성막을 dc magnetron sputtering법으로 각각 제조한 후 인덕터의 구조를 변화시켜, 인덕터의 임피던스 특성에 미치는 자성막의 특성 인자에 대해 연구하였다. 공심 인덕터의 전류 방향과 자성 박막의 자화 용이축이 수직일 경우 인덕터의 인덕턴스가 향상되었고, 공심 인덕터와 F $e_{86.7}$Z $r_{3.3}$ $B_{4}$A $g_{6}$ 자성막 사이 절연막이 없는 경우 자성막의 자속 집속효과가 증가하여 절연막이 있는 경우보다 인덕턴스는 높고, 저항의 증가율이 높았으며, F $e_{86.7}$Z $r_{3.3}$ $B_{4}$A $g_{6}$ 자성막의 투자율이 높을수록 인덕터의 인덕턴스에 기여하는 부분이 증가하므로 인턱턴스는 향상되었다. 또한 인덕터의 주파수 특성은 공심 인덕터의 특성에 지배적인 영향을 받으므로 인덕터의 주파수 특성을 향상시키기 위해서는 자성막의 특성보다 공심 인덕터의 특성을 향상시키는 것이 바람직하다.키는 것이 바람직하다.

• The Korean Journal of Pain
• /
• 제8권2호
• /
• pp.350-353
• /
• 1995

The first lesion in neural tissue produced by electrical currents were made in the 19th century by workers using direct current. In 1953, Sweet and Mark clearly demonstrated that DC lesions have unpredictable and ragged borders and may vary in size. They, as well as Hunsperger and Wyss, suggested that the use of high frequency currents might provide improved results and were proved correct. However, $Bovie^{(R)}$ electrosurgical unit may also be used in percutaneous medial branch neurotomy if a lesion made at a point or the dorsal surface of the transverse process just caudal to the most medial end of the superior edge of the transverse process (Bogduk's method). At this point the medial branch lies on the bone and its depth and medial displacement are defined by the bone which precludes the need for lateral radiographs to check placement. A lesion was made at same target point using the $Bovie^{(R)}$ electrosurgical unit in a 41 year male patient who had received a Kaneda operation because of L2 compression fracture. The patient was relieved of pain without any adverse effects.

• 전기학회논문지
• /
• 제62권6호
• /
• pp.798-802
• /
• 2013

In a conventional DC power supply used for CO2 laser, the circuit elements such as a rectifier bridge, a current-limiting resistor, a high voltage switch, energy storage capacitors ans a high-voltage isolation transformer using high turn ratio are necessary. Consequently, those supplies are expensive and require a large space. Thus, laser resonator and power supply should be optimally designed. In this paper, we propose a new power supply using high frequency resonance phenomena for CW(Continuous wave) CO2 laser (maximum output of 23W with discharge length of 450mm). It consists of a transformer including leakage inductance, magnetizing inductance and half-bridge converter, a three-stage Cockcroft-Walton and PFC(Power factor correction) circuit. The output ripple voltage can be controlled the minimum of 0.24% under the high frequency switching of 231kHz. Furthermore, the output efficiency was improved to 16.4% and the laser output stability of about 5.6% was obtained in this laser system.

• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2018년도 추계학술대회
• /
• pp.39-42
• /
• 2018

본 논문에서는 진동 에너지 수확을 위한 MPPT 제어기능을 갖는 인터페이스 회로를 설계하였다. 설계된 회로는 수확된 교류 형태의 에너지를 시스템 구동에 필요한 직류 형태의 에너지로 정류하고, MPPT Controller를 통해 Open Circuit Voltage(Voc)를 주기적으로 샘플/홀드한 뒤, 입력전압을 최대 가용 전력점의 1/2되는 전압으로 유지시키면서, 수확된 전력을 부하에 전달하는 동작을 한다. 모든 회로들은 0.35-um CMOS 기술을 기반으로 설계되었으며, 모의실험을 통하여 동작을 검증하였다. 모의실험 결과 설계된 회로는 3V 입력전압에서 98nA의 전류를 소모하며, 최대 전력효율은 99.21%이다. 설계된 회로의 칩 면적은 $1.281mm{\times}1.236mm$ 이다.

• 한국전기전자재료학회논문지
• /
• 제20권12호
• /
• pp.1093-1098
• /
• 2007

Tilting trains are currently in operation in 13 countries around the world. With the advances in tilting technology, verification of economic efficiency, and changes in economic situations, the introduction of tilting trains will rapidly spread across the globe. The measurement system is composed of the industrial computers installed in the console and the measurement racks mounted on each car. It is utilized to accumulate the data by the communication card and the optical cable. The optical cable and power cable are coupled at the connector located in joint of train to make easy to disconnect car each other. The signal conditioner is designed to choose and to extend the channel for each sensor readily. The sensor measurement rack has adopted as decentralization method. It is installed in each car to minimize the cable length. In also, it is manufactured based on 19"rack and covered to protect the cable. In this study, the programs for measurement and analysis were also developed to understand the traction system characteristics of TTX. Using this measurement system, we studied that acceleration test, re-powering test, and gradually powering test. The acceleration performance of TTX is 1.735 km/h/s, and it is inner standard value. The notch test result from 1 to 7 steps, DC link voltage is under standard value, and the output electric current of inverter is controlled normally. From the test results, we saw the performances of the traction systems are normal.

• 대한화학회지
• /
• 제36권3호
• /
• pp.412-418
• /
• 1992

비수용매인 아세토니트릴 중에서 Cu(Ⅱ)와 1,5,9,13-tetrathiacyclohexadecane[16-ane-$S_4$]의 착물에 대한 전기화학적 거동으로서 직류폴라로그램과 미분펄스폴라로그램으로부터 환원전류의 유형과 가역성을 조사하고, 이들 화합물의 분석적 응용으로서 수용액에 있는 Cu(Ⅱ) 이온을 염석추출법으로 정량하였다. 또한 아세토니트릴 용매 중에서 착물의 안정도 상수를 구하고, 분석적 응용으로 수용액 중의 Cu(Ⅱ)를 염석추출법으로 정량하기 위하여 추출조건, 곧 킬레이트와 염석제의 효과, pH 범위를 구하고 또한 Cu(Ⅱ) 이온을 정량하는데 있어서의 검량성과 공존이온 효과를 조사하였다. 실험결과로부터 환원 과정은 비가역적이었으며 환원전류는 확산지배적임을 알았다. 또한 아세토닐트릴 용매 중에서 착물의 log $K_f$의 값은 3.51이었으며 Cu(Ⅱ) 이온을 정량하는데 있어 공존하는 이온의 영향을 별로 받지 않아 선택성이 좋았으며 본 실험방법에 의한 정량한계는 60ppb 이었다.

• Journal of Power Electronics
• /
• 제15권1호
• /
• pp.190-201
• /
• 2015

This paper uses the switching function approach to present a simple state model of the Vienna-type rectifier. The approach introduces the relationship between the DC-link neutral point voltage and the AC side phase currents. A novel direct power control (DPC) strategy, which is based on the sliding mode control (SMC) for Vienna I rectifiers, is developed using the proposed power model in the stationary ${\alpha}-{\beta}$ reference frames. The SMC-based DPC methodology directly regulates instantaneous active and reactive powers without transforming to a synchronous rotating coordinate reference frame or a tracking phase angle of grid voltage. Moreover, the required rectifier control voltages are directly calculated by utilizing the non-linear SMC scheme. Theoretically, active and reactive power flows are controlled without ripple or cross coupling. Furthermore, the fixed-switching frequency is obtained by employing the simplified space vector modulation (SVM). SVM solves the complicated designing problem of the AC harmonic filter. The simplified SVM is based on the simplification of the space vector diagram of a three-level converter into that of a two-level converter. The dwelling time calculation and switching sequence selection are easily implemented like those in the conventional two-level rectifier. Replacing the current control loops with power control loops simplifies the system design and enhances the transient performance. The simulation models in MATLAB/Simulink and the digital signal processor-controlled 1.5 kW Vienna-type rectifier are used to verify the fast responses and robustness of the proposed control scheme.