• Proceedings of the KIPE Conference
• /
• 2012.07a
• /
• pp.201-202
• /
• 2012

This paper presents a simple and cost-effective stand-alone rapid battery charging system of 30kW for electric vehicles. The proposed system mainly consists of active front-end rectifier of neutral point clamped 3-level type and non-isolated bi-directional dc-dc converter of multi-phase interleaved half-bridge topology. The charging system is designed to operate for both lithium-polymer and lithium-ion batteries. The complete charging sequence is made up of three sub-interval operating modes; pre-charging mode, constant-current mode, and constant-voltage mode. Each mode is operated according to battery states: voltage, current and State of Charging (SOC). The proposed system is able to reach the full-charge state within less than 16min for the battery capacity of 8kWh by supplying the charging current of 67A. The optimal discharging algorithm for Vehicle to the Grid (V2G) operation has been adopted to maintain the discharging current of 1C. Owing to the simple and compact power conversion scheme, the proposed solution has superior module-friendly mechanical structure which is absolutely required to realize flexible power expansion capability in a very high-current rapid charging system. Experiment waveforms confirm the proposed functionality of the charging system.

• Proceedings of the KIPE Conference
• /
• 2012.07a
• /
• pp.377-378
• /
• 2012

DC-DC 컨버터를 인터리브 방식으로 제어하면 출력 전류 리플이 저감되고, 출력 필터 커패시터의 용량을 줄일 수 있다. 하지만 공진(Resonance)을 통해 전력을 전달하는 LLC 공진형 컨버터의 경우 회로를 구성하는 공진 인덕터 및 공진 커패시터의 오차(Tolerance)로 인해 출력 전류 리플의 언밸런스가 심화될 수 있다. 따라서 이를 개선할 수 있는 방법에 대한 연구가 필요하다. 본 논문에서는 Y결선 정류기를 이용한 3상 인터리브드 LLC 공진형 컨버터의 출력 전류 리플 밸런싱 방법을 제안한다. 제안된 방법은 3상 인터리브드 LLC 공진형 컨버터와 각 LLC 공진형 컨버터 앞단의 Bridgeless PFC가 독립적으로 추가되어 회로가 구성된다. 3상 인터리브드 LLC 공진형 컨버터는 분할된 위상으로 비독립적으로 제어하며 출력 전류 리플의 언밸런스를 Bridgeless PFC의 출력 전압을 가변함으로써 개선할 수 있는 방법을 제안하고 이를 시뮬레이션(PSIM)을 통해 제안된 밸런싱 방법을 검증하였다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.11
• /
• pp.948-952
• /
• 2007

In this study, a low temperature sintering multilayer piezoelectric transformer for a DC-DC converter was manufactured using $(Pb,Ca,Sr,)(Ti,Mn,Sb)O_3$ ceramics. Its electrical properties were investigated according to the variation in frequency and load resistance. The voltage step-up ratio of the multilayer piezoelectric transformer showed a maximum value at a resonant frequency of input part and increased with an increase of load resistance. The efficiency of the multilayer piezoelectric transformer showed the highest value at a load resistance of 17 $\Omega$. The output power was increased with increasing input voltage. Temperature increase of the multilayer piezoelectric transformer was increased with the increase of output power. At the load resistance of 17 $\Omega$, the multilayer piezoelectric transformer showed the temperature rises of about $20^{\circ}C$ at the output power of 18 W, and stable driving characteristics.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.11
• /
• pp.2223-2228
• /
• 2009

Dye sensitized solar cells(DSCs) have been very economical and easy method to convert solar energy to electricity. DSC can reach low costs in future outdoor power applications. However, to commercialize the DSC, there are still many shortages to overcome such a low efficiency in a large size DSC. In this study, DSCs were fabricated by an electrospray coating method for the $TiO_2$ thin film. They were compared with DSCs prepared by conventional coating methods. We conducted an experiment to obtain the optimized parameters of voltage, flow rate, incident angle and distance in the electrospray method. After we fabricated $TiO_2$ film using that way, we investigated the characteristics of DSC through I-V Curve, SEM and EIS. This novel method shows stable performance with an energy conversion efficiency of 3.44 % under 1 sun illumination (AM 1, $P_{in}$ of $100\;mW/cm^2$).

• Proceedings of the KIEE Conference
• /
• 1995.07a
• /
• pp.443-445
• /
• 1995

Since the residential load is an AC load, while the output of solar cell is a DC power, the photovoltaic system needs the DC/AC converter to utilize solar cell and must provide the sinusoidal wave current and voltage with unity power factor in the case of driving to Interact with utility line. It is always necessary for the output of solar cell to operate in the vicinity of maximum power point, since it is greatly fluctuated by insolation. This paper treats that we will constitute a single phase PWM voltage source inverter and trace the modulation index which always maximize the output of solar cell in propotion to insolation variation and prove it by simulation that we can provide current wave, which is nearly sinusoidal wave with unity power factor, for load and utility line.

• Proceedings of the KIPE Conference
• /
• 2015.11a
• /
• pp.7-8
• /
• 2015

In this paper a cell-to-cell fast charge balancing circuit for the Lithium-Ion battery module is proposed. In the proposed topology the energy in a high voltage cell is transferred directly to a low voltage cell through the operation of the dc-dc converter. Furthermore, the charge balancing can be performed regardless of the battery operation whether it is being charged, discharged or relaxed. The monitoring circuit composed of a DSP and a battery monitoring IC is designed to monitor the cell voltage and detect the inferior cell thereby protecting the battery module from failure. In order to demonstrate the performance of the proposed topology, a prototype circuit was designed and applied to 12 Lithium-Ion battery module. It has been verified with the experiments that the charge equalization time of the proposed method was shorter compared with those of other methods.

• Journal of Power Electronics
• /
• v.17 no.4
• /
• pp.1088-1096
• /
• 2017

Load variations on a distribution line result in voltage fluctuations at the point of common coupling (PCC). In order to keep the magnitude of the PCC voltage constant at its rated value and obtain zero voltage regulation (ZVR), a D-STATCOM is installed for voltage correction. Moreover, the ZVR mode of a D-STATCOM can also be used to balance the source current during unbalanced loading. For medium voltage and high power applications, a D-STATCOM is realized by the cascaded H-bridge topology. In the ZVR mode, the D-STATCOM may draw unbalanced current and in this process is required to handle different phase powers leading to deviations in the cluster voltages. Zero sequence voltage needs to be injected for ZVR mode, which creates circulating power among the phases of the D-STATCOM. The computed zero sequence voltage and the individual DC capacitor balancing controller help the DC cluster voltage follow the reference voltage. The effectiveness of the control scheme is verified by modeling the system in MATLAB/SIMULINK. The obtained simulations are further validated by the experimental results using a dSPACE DS1106 and five-level D-STATCOM experimental set up.

• Journal of Power Electronics
• /
• v.19 no.1
• /
• pp.179-189
• /
• 2019

Four-quadrant converters (4QCs) are widely used as AC-DC power conversion interfaces in many areas. A control delay commonly exists in the digital implementation process of 4QCs, especially for high power 4QCs with a low switching frequency. This usually results in alternating current distortion, increased current harmonic content and system instability. In this paper, the control delay is divided into a computation delay and a PWM delay. The impact of the control delay on the performance of a 4QC is briefly analyzed. To obtain a fundamental value of AC current that is as accurately as possible, a specific sampling method considering the PWM pattern is introduced. Then a current predictive control based on a modified z-transform is proposed, which is effective in reducing the control delay and easy in terms of digital implementation. In addition, it does not depend on object models and parameters. The feasibility and effectiveness of the proposed predictive current control method is verified by simulation and experimental results.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.21 no.6
• /
• pp.857-864
• /
• 2018

This paper describes about the circuit design and test of the electronic Arm Fire Device. Electronic arm fire device consists of igniter, circuit and housing case and it operates without the actuator such as torque motor or solenoid. A high-voltage DC-DC converter was used to generate the voltage for initiating the LEEFI(Low Energy Exploding Foil Initiator). The MEMS switch was used to detect the acceleration that occurs when missile is launched, and the circuit was designed considering the size, performance, and specification of the electronic devices. The performance test was conducted to verify the designed circuit and we confirmed that it operates well.

• Proceedings of the KIPE Conference
• /
• 2020.08a
• /
• pp.139-141
• /
• 2020

본 논문에선 다수의 변압기를 도입하여 복수의 입출력 포트 간 전력 동조화 문제를 해결할 수 있는 Quadruple-Active-Bridge(QAB) 컨버터를 제안한다. 기존 QAB 컨버터는 단일 변압기를 사용하기 때문에 입출력 포트 사이의 전력 동조화 문제가 발생한다. 따라서 단일 변압기에서 포트 간 전력 비동조화를 달성하기 위해 입력 포트의 누설 인덕턴스를 최소화하는 최적의 변압기 설계가 필요하나, 복수의 권선 구조로 인해 최적의 설계가 어렵다는 단점이 있다. 이러한 문제점을 해결하고자 본 논문에선 기존의 단일 변압기와 복수의 변압기를 함께 설치하는 구조를 제안한다. 제안한 구조를 통해 별도의 비동조화 알고리즘 없이 출력 포트 사이의 전력 동조화 문제를 해결할 수 있다. 그리고 변압기의 설계도 복잡했던 기존 QAB 와는 달리 쉬워지는 이점도 있다. 제안한 컨버터의 구조 및 전력 비동조화를 등가 모델을 통해 이론적으로 분석한다. 그리고 이를 검증하고자 3 kW급 시작품을 통해 전력전달 구조 및 전력 비동조화를 검증한다.