• Title/Summary/Keyword: DC/DC

Search Result 13,296, Processing Time 0.043 seconds

A Comparative Study of Commercial Catalysts for Methanol Steam Reforming (메탄올 수증기 개질반응에서의 상용촉매 비교연구)

  • Park, Jung-Eun;Park, Jae-Hyun;Yim, Sung-Dae;Kim, Chang-Soo;Park, Eun-Duck
    • Korean Chemical Engineering Research
    • /
    • v.49 no.1
    • /
    • pp.21-27
    • /
    • 2011
  • The comparison work was conducted for the methanol steam reforming among commercial Cu-based catalysts, viz. ICI-M45, which is for the methanol synthesis, MDC-3 and MDC-7, which are for the water-gas shift reaction. The catalytic activity for the water-gas shift reaction was also compared over three catalysts. Among them, MDC-7 showed the highest methanol conversion and formation rate of hydrogen and carbon dioxide at 473 K for the methanol steam reforming. To find out any promotional effect between ICI-M45 and MDC-7, three different packing methods with these two catalysts were examined. However, no synergistic effect was observed. The catalytic activity for watergas shift reaction decreased in the following order: MDC-7 > MDC-3 > ICI-M45. The highest activity of MDC-7 for the methanol steam reforming as well as the water-gas shift reaction can be due to its high surface area, copper dispersion, and an adequate Cu/Zn ratio.

EFFECTS OF SMEAR LAYER AND DENTIN PRIMERS ON THE SEALING ABILITY OF ROOT CANAL (근관 밀폐도에 미치는 도말층 및 상아질 접착강화제의 영향)

  • Yang, Jin-Suck;Hwang, In-Nam;Kim, Won-Jae;Oh, Won-Mann
    • Restorative Dentistry and Endodontics
    • /
    • v.25 no.4
    • /
    • pp.527-535
    • /
    • 2000
  • The purpose of this study was to evaluate effects of smear layer and dentin primers on the sealing ability of root canals. 126 extracted human teeth with single, straight canals and mature apices were used. The Samples were first classified into six groups as follows: presence of smear layer; absence of smear layer; Scotchbond Bond Multi-Purpose; All Bond 2; Mac Bond 2; Clearfil Liner Bond 2. A Positive control was also established. All teeth except the control group were then obturated with thermoplasticized gutta-percha and AH26. Electrochemical and dye penetration technique were later used to evaluate the degree of micro leakage through the root canal. Seventy teeth were then immersed in a 1% potassium chloride solution and An external power supply(DC 10 V) was then applied to the circuit for the electrochemical microleakage test. The degree of Microleakage was determined over period of 28 days before being evaluated. In total, 48 teeth were submitted to the dye infiltration technique. All specimen were suspended in 2% methylene blue dye for 1 week before being longitudinally split. The degree of dye infiltration was measured under a stereo microscope at ${\times}10$ magnification and evaluated. The results were as follows: 1. Apical microleakage increased throughout the test period in all group and one group having a smear layer showed a dramatic increase under electrochemical test (p<0.05). In the group having smear layer, the degree of apical microleakage was the highest, and the micro leakage was much higher than in the smear layer removed group in electrochemical test (p<0.05). Scotchbond Multi-Purpose, All Bond 2, Mac Bond 2 and Clearfil Liner Bond 2 showed lower micro leakage than one group having smear layer. The All Bond 2 and Clearfil Liner Bond 2 treated groups showed the lowest microleakage in electrochemical test (p<0.05). 2. There was no significant difference between the experimental groups in dye penetration technique. These results suggested that the removal of the smear layer from root canal and concomitantly the application of dentin primer into root canal could improve the sealing ability of root canal obturation.

  • PDF

Growth of Nanocrystalline Diamond on W and Ti Films (W 및 Ti 박막 위에서 나노결정질 다이아몬드의 성장 거동)

  • Park, Dong-Bae;Myung, Jae-Woo;Na, Bong-Kwon;Kang, Chan Hyoung
    • Journal of the Korean institute of surface engineering
    • /
    • v.46 no.4
    • /
    • pp.145-152
    • /
    • 2013
  • The growth behavior of nanocrystalline diamond (NCD) film has been studied for three different substrates, i.e. bare Si wafer, 1 ${\mu}m$ thick W and Ti films deposited on Si wafer by DC sputter. The surface roughness values of the substrates measured by AFM were Si < W < Ti. After ultrasonic seeding treatment using nanometer sized diamond powder, surface roughness remained as Si < W < Ti. The contact angles of the substrates were Si ($56^{\circ}$) > W ($31^{\circ}$) > Ti ($0^{\circ}$). During deposition in the microwave plasma CVD system, NCD particles were formed and evolved to film. For the first 0.5h, the values of NCD particle density were measured as Si < W < Ti. Since the energy barrier for heterogeneous nucleation is proportional to the contact angle of the substrate, the initial nucleus or particle densities are believed to be Si < W < Ti. Meanwhile, the NCD growth rate up to 2 h was W > Si > Ti. In the case of W substrate, NCD particles were coalesced and evolved to the film in the short time of 0.5 h, which could be attributed to the fact that the diffusion of carbon species on W substrate was fast. The slower diffusion of carbon on Si substrate is believed to be the reason for slower film growth than on W substrate. The surface of Ti substrate was observed as a vertically aligned needle shape. The NCD particle formed on the top of a Ti needle should be coalesced with the particle on the nearby needle by carbon diffusion. In this case, the diffusion length is longer than that of Si or W substrate which shows a relatively flat surface. This results in a slow growth rate of NCD on Ti substrate. As deposition time is prolonged, NCD particles grow with carbon species attached from the plasma and coalesce with nearby particles, leaving many voids in NCD/Ti interface. The low adhesion of NCD films on Ti substrate is related to the void structure of NCD/Ti interface.

Characteristics of BDD electrodes deposited on Ti substrate with TiN interlayer (TiN 중간층을 삽입하여 Ti기판 위에 증착한 BDD전극의 특성 평가)

  • Kim, Sin;Kim, Seo-Han;Yun, Jang-Hui;Song, Pung-Geun
    • Proceedings of the Korean Institute of Surface Engineering Conference
    • /
    • 2017.05a
    • /
    • pp.113-113
    • /
    • 2017
  • 최근 많은 산업의 발전으로 인해 환경오염을 유발시키는 폐수가 다량으로 배출되고 있으며, 이러한 폐수 속에는 유기용매, 고분자 물질 및 각종 염 등의 난분해성 물질들이 다량으로 함유되어 있다. 이런 물질들을 분해시키기 위해 물리적, 생물학적 수처리 방법이 많이 이용되고 있지만 이 방법들은 각각 운전비용과 처리비용이 고가인 단점이 있다. 따라서 비용과 효율 측면에서 효과적인 폐수처리를 위해서 전기화학적 폐수처리 방법이 많이 사용되고 있다. 물리적, 생물학적 처리 방법에 비해 비용이 적게 들고, 처리 후 잔류물이 남지 않으며, 독성을 띄는 산화제의 첨가 없이도 높은 폐수처리 능력을 보이기 때문에 친환경적이므로, 전기화학적 폐수산화 처리에 사용되는 불용성 전극에 대한 연구가 많이 진행되어져 오고 있다. 그 중 BDD(Boron-doped diamond) 전극은 표면에서 강력한 산화제인 수산화 라디칼의 높은 발생량으로 인해 뛰어난 폐수처리 능력을 보이므로 불용성 전극 분야에서 활발한 연구가 진행 중이다. 그러나 기존에 BDD 전극의 기판 모재로 이용되던 Si, W, Pb등은 모두 기계적 강도, 폐수처리 능력 및 독성 문제로 인해 한계가 있었고, 특히 Nb기판 위에 형성시킨 BDD 전극은 뛰어난 폐수처리 능력에도 불구하고 비싼 모재 원가로 인해 상용화가 힘든 실정이다. 이런 문제점을 해결하기 위해 높은 기계적 강도와 전기화학적 안정성을 가진 Ti 기판을 사용한 BDD 전극에 대한 연구가 보고되고 있다. 그러나 BDD와 Ti 간의 lattice mismatch, BDD층 형성을 위한 고온 공정시 탄소의 확산으로 인한 기판 표면에서의 TiC층 형성으로 인해 접착력이 감소하여 박리가 생기는 문제점이 있다. BDD와 Ti의 접착력을 향상시키기 위해 융점이 높고, 전기전도성이 우수한 TiN을 diffusion barrier layer로 삽입하면 탄소 확산에 의한 TiC층의 생성을 억제하여, 내부응력에 기인한 접착력 감소를 방지할 수 있다. 또 하나의 방법으로 Ti 기판의 전처리를 통해 BDD층의 접착력을 향상 시킬 수 있다. Sanding과 etching을 통해 기판 표면의 물리, 화학적인 표면조도를 부여하고, seeding을 통해 diamond 결정 성장에 도움을 주는 seed 입자를 분포시킴으로써, 중간층과 BDD층의 접착력을 향상시키고, BDD 결정핵 성장을 촉진시켜 고품질의 BDD박막 증착이 가능하다. 본 연구에서는 기존 Si, Nb 등의 기판 모재를 Ti로 대체함으로써 제조원가를 절감시키고, TiN 중간층을 삽입하여 접착력을 향상 시킴으로써 기존의 BDD 전극과 동등한 수준의 물성 및 수처리 특성을 가진 BDD전극 제작을 목표로 하였다. $25{\times}25mm$의 Ti 기판위에 TiN 중간층을 DC magnetron sputtering을 이용하여 증착 후, BDD 전극 층을 HFCVD로 증착하였다. 전처리를 진행한 기판과 중간층 및 BDD층의 미세구조를 XRD로 분석하였고, 표면 형상을 SEM으로 확인하였다. BDD전극의 접착력 분석을 통해 TiN 중간층의 최적 조성을 도출하고, 최종적으로 BDD/TiN/Ti 전극의 CV특성과 가폐수의 COD분해능력 및 축산폐수, 선박평형수 등의 실제 폐수 처리 능력을 BDD/Si, BDD/Nb 전극과 비교 검토할 것이다.

  • PDF

EFFECT OF RESIN MATRIX ON DEGREE OF CONVERSION AND FRACTURE TOUGHNESS OF DENIAL COMPOSITES (기질레진의 조성에 따른 복합레진의 물리적 성질에 관한 연구)

  • Lee, Yun-Shin;Choi, Kyoung-Kyu;Park, Sang-Jin
    • Restorative Dentistry and Endodontics
    • /
    • v.27 no.1
    • /
    • pp.77-86
    • /
    • 2002
  • Current composites are made with dimethacrylate monomers and silane-treated silica microfillers, either alone or with silane treated glass fillers The main reasons for clinical failure of dental composites are secondary caries, wear and fracture. Most of practitioner want to get a composite which is more tougher under occlusal stress, less polymerization contraction, and better handling properties in application clinically. The aim of this study was to investigate the influence of resin matrix with various flows on the physical proper-ties such as fracture toughness and degree of conversion of the experimental resins. It was hypothesized that flexible or tough resin composites can be designed by judicious choice of monomer composition Various flow resin matrices containing Bis-GMA, UDMA, and TEG-DMA were made by altering the pro-portion of the monomers. After the unfilled resins were light-cured for different light intensity, the fracture toughness(K$_{1c}$) was measured according to ASTM standard using the single edge notched geometry, and degree of conversion(DC) was measured by FTIR. And experimental composites were formulated with variations in the proportion of silanated quartz and strontium glass fillers as 60, 75, and 77wt%. Also, the physical properties of composites with various filer contents were evaluated as same manner. All resulting data were compared by ANOVA/Tukeys test at 0.05 level. The results were as follows; 1. The degree of conversion of high flow resin containing less Bis-GMA was higher than that of low flow unfilled resin 2. While the degree of conversion of unfilled resin was increased according to light intensity for polymerization, there was no significant increase with moderate and high light intensity. Also, the fracture toughness was not increased by high light intensity. 3. The fracture toughness was high in the low flow unfilled resin containing higher contents of Bis-GMA. 4. There was a significant increase for fracture toughness and a tendency for degree of conversion to be reduced when the content of fillers was increased. 5. In the experimental composites, the flow of resin matrix did not affected on the fracture toughness, even, which was decreased as increase of viscosity. These results showed that the physical properties of a dental composite could be attributed to the flow of resin matrix with relative content of monomers. Specific combination of resin monomers should be designed to fulfil the needs of specific indication for use.

Notes on Powdery mildew of Ailanthus altissima caused by Phyllactinia corylea (Pers.) Karst (Phyllactinia corylea (Pers.) Karst에 의(依)한 가중나무 흰가루병(病))

  • Kim, Ki Chung
    • Journal of Korean Society of Forest Science
    • /
    • v.4 no.1
    • /
    • pp.9-13
    • /
    • 1965
  • Powdery mildew of Ailanthus altissima Sw. was first reported by J.S. Park in Korea, 1961. According to his report, this disease was found on the leaves of this tree species collected in Jeongup, 1957, and in Taejon, 1958. He described morphological characters of this pathogen and described also that the causal fungus may be closely related with Phyllactinia corylea. This disease which appears dusty grayish yellow molds under surface of leaves was collected again by the author in Kwangju, 1962. The present works were undertaken to make clear the species of causal fungus by means of the morphology and pathogenecity. According to the following results, the pathogen was identified as Phyllactinia corylea (Pers.) Karst. Morphological characters of the fungus Mycelia persistent or more or less evanescent; matured conidia solitary, aseptate, short-clavate to clavate to clavate, hyaline or yellowish, granulate, $44.6-89.2{\times}9.3-24.2{\mu}$, average $64.8-17.8{\mu}$ in size; conidiophores elongate clavate or columnar, hyaline, 2-3 septate, $122.8-346.0{\times}3.7-7.4{\mu}$, average $208.8{\times}6.3{\mu}$; per-thecia usually scattered, rarely gregarious, dark brown to black, depressed globose to globose, $223.2-297.6{\mu}$, average $267.8{\mu}$ in diameter; appendages 12-19, usually 15 in number, hyaline, straight, needle-shaped, sharply pointed at the apex and bulbous at the base, aseptate, $93.0-310.0{\times}5.0-8.0{\mu}$, average $173.3{\times}6.4{\mu}$ in size; asci elongate ellipsoidal to broadly clavate, hyaline, more or less stalked, 8-13 in number, $68.5-76.6{\times}26.1-34.2{\mu}$, average $71.4{\times}29.0{\mu}$ in size; ascospores 2-4, usually 2 in number, hyaline or yellowish, aseptate, ellipsoidal or ovate, $27.7-34.2{\times}14.7-17.9{\mu}$, average $25.5{\times}13.9{\mu}$ in size. Pathogenicity of the fungi In order to make clear the species of the fungus and the pathogenic differences of Phyllactinia fungi which are collected around the contaminated area and seemed to be related to Ailanthus powdery mildew, some inoculation experiments were performed. 1. Cross inoculation to several tree species with their pathogen: Tested materials; Phyllactinia in question on Ailanthus altissima Sw. Ph. fraxini (DC.) Homma. On Alnus firma S. et Z. Ph. moricola (P. Henn.) Homma on morus alba L. According to the results of the experiments, the reactions were all negative with the exception of the original hosts of tested fungi. 2. Inoculation to Picrasma ailanthoides Planch. : The appearance of symptom on the leaves of P. ailanthoides is not distinct, but more or less mycelial growth. Therefore, under the optimal condition in glass chamber, it may be possible to success artificially.

  • PDF

A Study on the Development of Reference Linking System Based on Digital Object Identifier for Korean Journal Articles (국내 학술지 논문의 DOI 기반 연계시스템 구축에 관한 연구)

  • 한혜영;정동열
    • Journal of the Korean Society for information Management
    • /
    • v.17 no.4
    • /
    • pp.207-227
    • /
    • 2000
  • Recenily, major internalional STM(Science, Trchnical, and Mcdivine) Publichers have been developing prototype systems that can provide the refeence linking of jouinal articles within the scholarly literature on a cross-publisher basis using the URN(Universal Resouree Name). In Korea, it is hard to find the efforts to link the scattered digitalized documents to an individual user through a unified web. In this study, a linking model for an inergrated gatewny fro, bibliographic information to full tcxt has been desugned and 'Electronic Research Resourced Linking system (E3R/LS)' has been developed as a prototype for centralized static reference linking system. There are three major components for constructing refrernce linking systems. The firsl componcnt the Digital Object Identifiet(DO1). is introduced as the public identifier inrended to be applied wherever thr item needs to be identified. For denl~iymg Korean journal articles, llie extended SICI(Serlal Ilem and Conlribut~on Idealifier) has becn newly dehed in 1111s study and is used as a suiiia on DOI. The reierence datubasc conlams the second com~onenl, metadiltil, linkcd to implemenied by all information providers. The CnRI resolution system is used for resolving a DOI into a URL as the third component.

  • PDF

ACQUISITION OF THE FLIGHT INFORMATION USING THE KSR-3 MAGNETOMETER (KSR-3 탑재 자력계를 이용한 비행정보 획득 연구)

  • Kim, Sun-Mi;Jang, Min-Hwan;Lee, Dong-Hun;Han, Young-Seok;Kim, Jun;Hwang, Seung-Hyun;Lee, Eun-Seok;Lee, Sun-Min;Kim, Hyo-Jin;Lee, Su-Jin
    • Journal of Astronomy and Space Sciences
    • /
    • v.20 no.1
    • /
    • pp.29-42
    • /
    • 2003
  • The KSR-3 magnetometers consist of the fluxgate magnetometer (MAG/AIM) for acquiring the rocket flight attitude information, and the search-coil magnetometer (MAG/SIM) for the observation of the Earth's magnetic fluctuations. The position (latitude, longitude, and height) and flight condition (the transformation angle) of the rocket is measured after the data based on these two magnetometers are compared with IGRF The gap in the vector of magnetic field between the position of the launching point and an impact point is taken into account in data reduction. Angular variation of pitch, yaw, and roll can be researched when the data is applied to the coordinate system of the rocket.

Amorphous Indium-Tin-Zinc-Oxide (ITZO) Thin Film Transistors

  • Jo, Gwang-Min;Lee, Gi-Chang;Seong, Sang-Yun;Kim, Se-Yun;Kim, Jeong-Ju;Lee, Jun-Hyeong;Heo, Yeong-U
    • Proceedings of the Korean Vacuum Society Conference
    • /
    • 2010.08a
    • /
    • pp.170-170
    • /
    • 2010
  • Thin-film transistors (TFT) have become the key components of electronic and optoelectronic devices. Most conventional thin-film field-effect transistors in display applications use an amorphous or polycrystal Si:H layer as the channel. This silicon layers are opaque in the visible range and severely restrict the amount of light detected by the observer due to its bandgap energy smaller than the visible light. Therefore, Si:H TFT devices reduce the efficiency of light transmittance and brightness. One method to increase the efficiency is to use the transparent oxides for the channel, electrode, and gate insulator. The development of transparent oxides for the components of thin-film field-effect transistors and the room-temperature fabrication with low voltage operations of the devices can offer the flexibility in designing the devices and contribute to the progress of next generation display technologies based on transparent displays and flexible displays. In this thesis, I report on the dc performance of transparent thin-film transistors using amorphous indium tin zinc oxides for an active layer. $SiO_2$ was employed as the gate dielectric oxide. The amorphous indium tin zinc oxides were deposited by RF magnetron sputtering. The carrier concentration of amorphous indium tin zinc oxides was controlled by oxygen pressure in the sputtering ambient. Devices are realized that display a threshold voltage of 4.17V and an on/off ration of ${\sim}10^9$ operated as an n-type enhancement mode with saturation mobility with $15.8\;cm^2/Vs$. In conclusion, the fabrication and characterization of thin-film transistors using amorphous indium tin zinc oxides for an active layer were reported. The devices were fabricated at room temperature by RF magnetron sputtering. The operation of the devices was an n-type enhancement mode with good saturation characteristics.

  • PDF

Anti-inflammatory Activity of the Galactomannans Produced by a New Fungal Strain Trichoderma erinaceum DG-312 (Trichoderma erinaceum DG-312 신규 곰팡이 균주로부터 생산된 galactomannan의 항염증 활성)

  • Joo Ji-Hoon;Lim Jong-Min;Koo Kwang-Bon;Yun Jong-Won;Choi Jang Won
    • Journal of Life Science
    • /
    • v.15 no.2 s.69
    • /
    • pp.287-292
    • /
    • 2005
  • The crude galactomannans (GMs) were obtained from the culture of a newly isolated fungus Trichoderma erinaceum DG-312 and their anti-inflammatory activity was investigated in mice. The maximum concentrations of mycelial biomass and GMs reached 9.44 g/l, 2.72 g/l at day 3 in a 5-l stirred-tank bioreactor, respectively. The results of Sepharose CL-6B gel chromatography and compositional analysis revealed that the crude GMs contain heterogeneous polysaccharides consisting of $74.9\%$ mannose and $24.1\%$ galactose. The GMs was shown to possess a significant anti-inflammatory activity against acetic acid-induced inflammatory mouse model in a dose-dependent manner, when mice were treated with 100 and 200 mg GMs/kg body weight. The inhibition in vascular permeability $(60.6\%)$ and in writhing response $(62.5\%)$ evidenced an anti-inflammatory activity of the GMs. The marked anti-inflammatory and writhing-lowering properties of the GMs suggest its potential therapeutic use.