• Journal of Electrical Engineering and Technology
• /
• v.9 no.6
• /
• pp.2065-2069
• /
• 2014

The DAC-7512E is a 12-bit digital to analog converter that is low power and a single package with internal buffers. The DAC-7512E takes up minimal PCB area for applications of space power electronics design. The spacecraft mass is a crucial point considering spacecraft launch into space. Therefore, we have performed a TID test for the DAC-7512E 12-bit serial input digital to analog converter to reduce the spacecraft mass by using a low-level Gamma-ray irradiator with $Co^{60}$ gamma-ray sources. The irradiation with $Co^{60}$ gamma-rays was carried out at doses from 0 krad to 100 krad to check the error status of the device in terms of current, voltage and bit error status during conversion. The DAC-7512E 12-bit serial digital to analog converter should work properly from 0 krad to 30 krad without any error.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.1
• /
• pp.129-134
• /
• 2014

This paper presents a 10-bit 10-MS/s asynchronous successive approximation register (SAR) analog-to-digital converter (ADC) which consists of a digital-to-analog converter (DAC), a SAR logic, and a comparator. The designed asynchronous SAR ADC with a rail-to-rail input range uses a binary weighted DAC using metal-oxide-metal (MOM) capacitor to improve sampling rate. The proposed 10-bit 10-MS/s asynchronous SAR ADC is fabricated using a 0.18-${\mu}m$ CMOS process and its active area is $0.103mm^2$. The power consumption is 0.37 mW when the voltage of supply is 1.1 V. The measured SNDR are 54.19 dB and 51.59 dB at the analog input frequency of 101.12 kHz and 5.12 MHz, respectively.

• Journal of the Korea Society of Computer and Information
• /
• v.7 no.4
• /
• pp.115-120
• /
• 2002

This paper presents the implementation of IS-95 CDMA signal processor, baseband and Intermediate Frequency(IF) digital converter using Field Programmable Gate Array(FPGA) and ADC/DAC and frequency up/down converter IS-95 CDMA channel processor is generated the pilot channel signal with short PN code and Walsh-code generator. The digital If is composed of FPGA. digital transmit/receive signal processor and high speed analog-to-digital converter(ADC) and digital-to-analog converter(DAC). The frequency up/down converter consisted of filter, mixer, digital attenuator and PLL is analog conversion between intermediate frequency(IF) and baseband. This implemented system can be deployed in the IS-95 CDMA base station device etc.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.2
• /
• pp.414-422
• /
• 2013

This paper describes a 10-bit 10-MS/s asynchronous successive approximation register (SAR) analog-to-digital converter (ADC) using a split-capacitor-based differential digital-to-analog converter (DAC). SAR logic and comparator are asynchronously operated to increase the sampling frequency. The time-domain comparator with an offset calibration technique is used to achieve a high resolution. The proposed 10-bit 10-MS/s asynchronous SAR ADC with the area of $140{\times}420{\mu}m^2$ is fabricated using a 0.18-${\mu}m$ CMOS process. Its power consumption is 1.19 mW at 1.8 V supply. The measured SNDR is 49.95 dB for the analog input frequency of 101 kHz. The DNL and INL are +0.57/-0.67 and +1.73/-1.58, respectively.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.14 no.1
• /
• pp.33-41
• /
• 2019

We propose an embedded solution to design a high-speed and high-accuracy 16bit analog-digital signal processing interface for the control systems using various external analog signals. Choosing TMS320F28377D micro controller unit (MCU) featuring high-performance processing in the 32-bit floating point operation, low power consumption, and various I/O device supports, we design and build the proposed system that supports both 16-bit analog-digital converter (ADC) interface and high precision digital-analog converter (DAC) interface. The ADC receives voltage-level differential signals from fully differential amplifiers, and the DAC communicates with MCU through 50 MHz bandwidth high-fast serial peripheral interface (SPI). We port the boot loader and device drivers to the implemented board, and construct the firmware development environment for the application programming. The performance of the entire implemented system is demonstrated by analog-digital signal processing tests, and is verified by comparing the test results with those of existing similar systems.

• Proceedings of the IEEK Conference
• /
• 2002.06b
• /
• pp.149-152
• /
• 2002

The performance of a 1-bit DAC depends on that of the analog circuits. The mixed SC-CT (switched capacitor-continuous time) architecture is an effective design methodology for the analog circuits. This paper Proposes a new buffer scheme for the 1-bit digital-to-analog subconverter and a new SF-DSC(smoothing filter and differential-to-sig le converter) which performs both the smoothing filter and the differential-to-single convertor simultaneously.

• International Journal of Internet, Broadcasting and Communication
• /
• v.5 no.2
• /
• pp.11-14
• /
• 2013

This paper describes the sigma-delta ADC/DAC digital block with two channels. The ADC block has comb filter and three half band filters. And the DAC block has 5th Cascaded-of-Integrators Feedback DSM. The ADC and DAC support I2S, RJ, LJ and selectable input data modes of 24bit, 20bit, and 16bit. It is fabricated with 0.35um Hynix standard CMOS cell library. The chip size is 3700*3700um. It has been verified using NC Verilog Simulator and Matlab Tool.

• 한국초전도학회:학술대회논문집
• /
• v.12
• /
• pp.39-39
• /
• 2002

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.7 no.1
• /
• pp.28-35
• /
• 2007

This paper presents a high-speed flash analog-to-digital converter (ADC) for ultra wide band (UWB) receivers. In this flash ADC, the interpolating technique is adopted to reduce the number of the amplifiers and a linear and wide-bandwidth interpolating amplifier is presented. For this ADC, the transistor size for the cascaded stages is inversely scaled to improve the trade-off in bandwidth and power consumption. The active inductor peaking technique is also employed in the pre-amplifiers of comparators and the track-and-hold circuit to enhance the bandwidth. Furthermore, a digital-to-analog converter (DAC) is embedded for the sake of measurements. This chip has been fabricated in $0.13{\mu}m$ 1P8M CMOS process and the total power consumption is 113mW with 1V supply voltage. The ADC achieves 4-bit effective number of bits (ENOB) for input signal of 200MHz at 5-GSample/sec.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.2
• /
• pp.258-264
• /
• 2011

In this paper, we designed a frequency synthesizer with a low phase noise and fast lock time and excellent spurious characteristics using the offset-PLL(Phase Locked Loop) that is used in GSM(Global System for Mobile communications). The proposed frequency synthesizer has low phase noise using three times down conversion and third offset frequency of this synthesizer is created by DDS(Direct Digital Synthesizer) to have high frequency resolution. Also, this synthesizer has fast switching speed using DAC(Digital to Analog Converter). but phase noise degraded due to DAC. we improved performance using the DAC noise filter.