• Applied Biological Chemistry
• /
• v.39 no.3
• /
• pp.172-176
• /
• 1996

Effect of culture conditions such as pH, temperature, agitation speed and oxygen transfer rate on xylitol production from xylose by Candide parapsilosis ATCC 21019 mutant was investigated in a jar fermentor. The initial concentration of xylosr was fixed at 50 g/l in this experiment. When pH was increased, cell growth and xylose consumption rate were increased, but maximum xylitol production was shown in the range of pH 4.5 and 5.5 with a yield of 0.68 g/g-xylose. The optimal temperature for xylitol production was determined to be $30^{\circ}C$. Considering the importance of dissolved oxygen tension, for xylitol production, the effect of oxygen transfer rate coefficient $(k_La)$ on fermentation parameters was carefully evaluated in the range of $20{\sim}85\;hr{-1}\;of\;k_La$ (corresponding to $100{\sim}300$rpm of agitation speed). The xylitol production was maximized at $30\;hr^{-1}\;of\;k_La$(150 rpm). A higher oxygen transfer rate supported better cell growth with lower xylitol yield. It was determined that maximum xylitol concentration, xylitol yield and productivity was 35.8 g/l, 71.6% and $0.58\;g/l{\sim}hr^{-1}$, respectively, at $30\;hr^{-1}\;of\;k_La$ In order to further increase xylitol productivity, ferementation using the concentrated biomass(20 g/l) was carried out at the conditions of pH 4.5, $30^{\circ}C$ and $30\;hr\;1$ of oxygen transfer rate. The final xylitol concentration of 40 g/l was obtained at 18 hours of culture time. From this result, it was calculated that xylitol yield was 80ft on the basis of xylose consumption and volumetric productivity was $2.22\;g/l{\sim}hr$ which was increased by $3{\sim}4$ fold compared with $0.5{\sim}0.7\;g/l-hr$ obtained in a normal fermentation condition.

• Journal of Korea Water Resources Association
• /
• v.53 no.8
• /
• pp.627-636
• /
• 2020

Debris flow disasters primarily occur in mountainous terrains far from cities. As such, they have been underestimated to cause relatively less damage compared with other natural disasters. However, owing to urbanization, several residential areas and major facilities have been built in mountainous regions, and the frequency of debris flow disasters is steadily increasing owing to the increase in rainfall with environmental and climate changes. Thus, the risk of debris flow is on the rise. However, only a few studies have explored the characteristics of flooding and reduction measures for debris flow in areas designated as steep slopes. In this regard, it is necessary to conduct research on securing independent disaster prevention technology, suitable for the environment in South Korea and reflective of the topographical characteristics thereof, and update and improve disaster prevention information. Accordingly, this study aimed to calculate the amount of debris flow, depending on disaster prevention performance targets for regions designated as steep slopes in South Korea, and develop an independent model to not only evaluate the impact of debris flow but also identify debris barriers that are optimal for mitigating damage. To validate the reliability of the two-dimensional debris flow model developed for the evaluation of debris barriers, the model's performance was compared with that of the hydraulic model. Furthermore, a 2-D debris model was constructed in consideration of the regional characteristics around the steep slopes to analyze the flow characteristics of the debris that directly reaches the damaged area. The flow characteristics of the debris delivered downstream were further analyzed, depending on the specifications (height) and installation locations of the debris barriers employed to reduce the damage. The experimental results showed that the reliability of the developed model is satisfactory; further, this study confirmed significant performance degradation of debris barriers in areas where the barriers were installed at a slope of 20° or more, which is the slope at which debris flows occur.

• Journal of Physiology & Pathology in Korean Medicine
• /
• v.20 no.4
• /
• pp.766-783
• /
• 2006

This study describes philosophical background regarding '虛' in oriental medicine in an effort to understand the relationships among some of the Eastern philosophy in accordance with differentiated meanings in several resources by analyzing examples of '虛' in Huang Di Nei Jing. The various usages of '虛' used in Huang Di Nei Jing are as follows: naming; condition of pulse; emptiness; '太虛' which was referred universal space by Chinese ; insufficiency, lack or scarcity, deficiency ; and the description of vitality, mental faculties. 外丹修煉(training by external substances) had the attitude do that withdraw the death by taking external materials. The meaning of '虛'in 外丹修煉 is similar to that in oriental medicine in terms of deficiency. That is, both 外丹修煉 and the oriental medicine consider that the death and disease are caused by the deficiency of something. However, there also exists difference between 外丹修煉 and the oriental medicine. 外丹修煉 supplements through withdrawal prohibition due to the characteristic of unchangeability and stern or immortal while oriental medicine provides concrete object of deficiency. 精(essence of life), 氣(ki, functional activity), and fe(vitality) not only have been considered as basic component of human body, but they also have been an important subject of health preservation for longevity with health in Taoism and oriental medicine. In oriental medicine, 精 and 氣 have been perceived as physical basis of human body and 神 as controller. 內丹修煉(Training of internal active substances) 掠nds to return to '虛', the early state of life through individual training, and attempts to withdraw death through continuous recurrence. The oriental medicine and 內丹修煉 held great value of 神 among health preservation of 精, 氣, and 神. They seek theoretical basis from philosophical Taoism. However, '虛' in Taoism is different from that in training by internal substances and oriental medicine: '虛' in philosophical Taoism has metaphysical concept which refers overcome of life and death, but '虛' in 內丹修煉 and oriental medicine have empirical concept. '太虛' is considered as formless space where it is emp Dut filled with 氣. It is conceptualized with the premise of the relevant adaptation of human body to natural environment theory referring that the interaction between the heaven and the earth makes changes; all creation is originated , and human is affected by the interaction of the heaven and the earth. Furthermore, in $\ulcorner$運氣七篇$\lrcorner$ (Seven chapters described about the five circuit phases and the six atmospheric influences), the expression that the earth is in the center of '太虛' and huge amount of 氣 supports it proves that $\ulcorner$運氣七篇$\lrcorner$ adapts '渾天設'(Chaotic universe thee). In Taoism, '虛' is the grounds where all creation is generated in the optimal condition of Tao. As regards the aspect of mentality, it is the condition in which one can free from the dualistic concepts such as right and wrong, beauty and ugliness, life and death, and so on. Although the ultimate goal of oriental medicine, the achievement of longevity without sickness, might contrast with the Taoist belief that perceives life and death as the natural phenomena or the flowing of the 氣, and eliminates all international, the idea of Taoism that one should live substantial life with naivety, and make Harmony with the nature might be influential to the oriental medicine.

• Journal of Plant Biotechnology
• /
• v.38 no.3
• /
• pp.221-227
• /
• 2011

This study was carried out to determine optimal medium conditions for mass propagation by bioreactor culture of ever-bearing strawberry (Fragaria ${\times}$ ananassa D.). Two different type of nitride were that mixed $NH_4NO_3$ and $KNO_3$ or added $KNO_3$ only. And nitride concentrations were at the 4 levels of $1/2{\times}$, $1{\times}$, $2{\times}$ and $3{\times}$ that was included $NH_4NO_3$ and $KNO_3$. Sucrose content ranged at 3 levels of $10g{\cdot}L^{-1}$, $20g{\cdot}L^{-1}$ and $30g{\cdot}L^{-1}$ and medium pH were at the 3 levels of 4.6, 5.6 and 6.6. In bioreactor culture, medium that are included $NH_4NO_3$ and $KNO_3$ together in MS medium was suitable for mass propagation. Medium EC rose rapidly when the nitride concentration was increased. For that reason, plantlet growth was inhibited. Shoots of nitride $1/2{\times}$ concentration was 10.8 ea and $1/2{\times}$ concentration was suitable for shoot propagation. Fresh weight of sucrose $30g{\cdot}L^{-1}$ was 3,101 mg which was heaviest and aerial and ground part were higher than the other concentration. Shoots were increased in proportion to the increasing concentration of sucrose. In the pH condition, from pH 5.6 to 6.8 were appropriate for the optimum growth of aerial and ground part of plant. From the results, in bioreactor culture for mass propagation, MS medium was suitable $1/2{\times}$ concentration that was included $NH_4NO_3$ and $KNO_3$ together, and added $30g{\cdot}L^{-1}$ of sucrose, and then adjusted pH between 5.6 and 6.6.

• Korean Journal of Food Science and Technology
• /
• v.50 no.1
• /
• pp.44-54
• /
• 2018

To maintain the best quality of kimchi during long-term storage, we developed a fermentation storage mode for the kimchi refrigerator. The optimal kimchi fermentation temperature was determined to be $6^{\circ}C$ with fermentation time of 4-7 days in winter and 3-5 days in spring and fall. Based on these results, the fermentation storage mode conditions were programmed to consist of a fermentation temperature of $6^{\circ}C$ and fermentation times of 111 h in winter and 58 h in spring/fall. When kimchi was stored under the developed fermentation storage mode conditions, the total acidity of kimchi was almost the same as that of the control kimchi (stored $-2-\;-1^{\circ}C$ for 12 weeks). However, the number of lactic acid bacteria (LAB) and Leuconostoc sp. in kimchi were higher ($10^1-10^2CFU/mL$) than those in the control kimchi during storage. In addition, kimchi fermented and stored under the fermentation storage mode clearly received higher scores for overall preference than the control kimchi.

• Journal of Korean Society of Transportation
• /
• v.23 no.2
• /
• pp.117-130
• /
• 2005

In both deteministic user Optimal Traffic Assignment Model (UOTAM) and stochastic UOTAM, travel time, which is a major ccriterion for traffic loading over transportation network, is defined by the sum of link travel time and turn delay at intersections. In this assignment method, drivers actual route perception processes and choice behaviors, which can become main explanatory factors, are not sufficiently considered: therefore may result in biased traffic loading. Even though there have been some efforts in Stochastic UOTAM for reflecting drivers' route perception cost by assuming cumulative distribution function of link travel time, it has not been fundamental fruitions, but some trials based on the unreasonable assumptions of Probit model of truncated travel time distribution function and Logit model of independency of inter-link congestion. The critical reason why deterministic UOTAM have not been able to reflect route perception cost is that the route perception cost has each different value according to each origin, destination, and path connection the origin and destination. Therefore in order to find the optimum route between OD pair, route enumeration problem that all routes connecting an OD pair must be compared is encountered, and it is the critical reason causing computational failure because uncountable number of path may be enumerated as the scale of transportation network become bigger. The purpose of this study is to propose a method to enable UOTAM to reflect route perception cost without route enumeration between an O-D pair. For this purpose, this study defines a link as a least definition of path. Thus since each link can be treated as a path, in two links searching process of the link label based optimum path algorithm, the route enumeration between OD pair can be reduced the scale of finding optimum path to all links. The computational burden of this method is no more than link label based optimum path algorithm. Each different perception cost is embedded as a quantitative value generated by comparing the sub-path from the origin to the searching link and the searched link.

• Journal of agriculture & life science
• /
• v.44 no.3
• /
• pp.41-52
• /
• 2010

This study was conducted to estimate genetic parameters for growth traits using multivariate animal models in Yorkshire breed. For the study, 16,202 records for growth traits collected between the year 1999 and 2005 from Yorkshire pigs in K GGP were used. The effects of environmental factors such as sex, birth year, birth season, parity and birth weight group affected growth traits significantly (p<0.01). Birth weight tended to be positively correlated with average daily gain (ADG) and lean percent. But it seemed to affect age at 90 kg, average adjusted backfat thickness (BF), and eye muscle ares (EMA) negatively. For average pig suckling weight (ASW) and total weight at suckling (TWS), the higher birth weight is the better performance. But, in case of total number of born and number of suckling, the result was shown vice versa. Approximately 10~30% lower heritability estimates were obtained for growth traits by using the model that includes descriptions of common litter effects (CL) than by using the model that ignores those (NCL) for more accurate estimation of heritability. The estimates of heritabilities were 0.468, and 0.328 for ADG, 0.474 and 0.326 for age at 90 kg, 0.452, and 0.396 for BF, 0.240 and 0.200 for EMA and, 0.458, and 0.380 for lean percent in NCL and CL, respectively. Therefore, in order to estimate optimal genetic parameters, it could be inferred that the statistical model which considers litter effects must be applied.

• Journal of Life Science
• /
• v.31 no.1
• /
• pp.90-99
• /
• 2021

In this study, to reduce the production cost of poly(3-hydroxyalkanoates) (PHA), optimal cell growth and PHA biosynthesis conditions of the isolated strain Pseudomonas sp. EML8 were established using waste frying oil (WFO) as the cheap carbon source. Gas chromatography (GC) and GC mass spectrometry analysis of the medium-chain-length PHA (mcl-PHAWFO) obtained by Pseudomonas sp. EML8 of WFO indicated that it was composed of 7.28 mol% 3-hydrxoyhexanoate, 39.04 mol% 3-hydroxyoctanoate, 37.11 mol% 3-hydroxydecanoate, and 16.58 mol% 3-hydroxvdodecanoate monomers. When Pseudomonas sp. EML8 were culture in flask, the maximum dry cell weight (DCW) and the mcl-PHAWFO yield (g/l) were showed under WFO (20 g/l), (NH4)2SO4 (0.5 g/l), pH 7, and 25℃ culture conditions. Based on this, the highest DCW, mcl-PHAWFO content, and mcl-PHAWFO yield from 3-l-jar fermentation was obtained after 48 hr. Similar results were obtained using 20 g/l of fresh frying oil (FFO) as a control carbon source. In this case, the DCW, the mcl-PHAFFO content, and the mcl-PHAFFO yields were 2.7 g/l, 62 wt%, and 1.6 g/l, respectively. Gel permeation chromatography analysis confirmed the average molecular weight of the mcl-PHAWFO and mcl-PHAFFO to be between 165-175 kDa. Thermogravimetric analysis showed decomposition temperature values of 260℃ and 274.7℃ for mcl-PHAWFO and mcl-PHAFFO, respectively. In conclusion, Pseudomonas sp. EML8 and WFO could be suggested as a new candidate and substrate for the industrial production of PHA.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.37 no.4
• /
• pp.217-224
• /
• 2021

Purpose: The purpose of this study was to evaluate the porosity of resin modified glass ionomer (RMGI) by different mixing methods. Materials and Methods: Five specimens were prepared for each groups according to capsules and mixing methods. Two RMGI capsule and two mixing machines were used for this study. One resin-modified glass ionomer cement is Fuji II LC (F2LC) and the other is Photac Fil Quick Aplicap (PFQ). For Mixing of RMGI capsule, Rotomix using rotating motion and CM-II using shaking motion were used. After measuring height, radius and mass of specimens, Density was calculated. And porosity was measured using micro-computed tomography (micro-CT). All data were statistically analyzed using T-test, two-way ANOVA to compare between groups at 95% significance level to evaluate the affect of capsule and mixing method on the porosity. Results: The porosity was observed in all specimens generally. And there is significant differece between porosities according to RMGI capsule and Mixing method. The porosity of PFQ was lower than that of F2LC and the porosity of Rotomix was lower than that of CM-II. Conclusion: There was a difference of porosity according to kind of capsules and mixing methods. When using same capsule, less porosity was observed on PFQ than F2LC. When using same mixing mehod, less porosity was observed on Rotomix than CM-II. Using mixing machine of same coporation as that of RMGI capsule did not lead to lower porosity. Therefore, Selecting optimal mixing machine is important.

• Korean Journal of Remote Sensing
• /
• v.38 no.6_3
• /
• pp.1827-1836
• /
• 2022

Disasters that occur unexpectedly are difficult to predict. In addition, the scale and damage are increasing compared to the past. Sometimes one disaster can develop into another disaster. Among the four stages of disaster management, search and rescue are carried out in the response stage when an emergency occurs. Therefore, personnel such as firefighters who are put into the scene are put in at a lot of risk. In this respect, in the initial response process at the disaster site, robots are a technology with high potential to reduce damage to human life and property. In addition, Light Detection And Ranging (LiDAR) can acquire a relatively wide range of 3D information using a laser. Due to its high accuracy and precision, it is a very useful sensor when considering the characteristics of a disaster site. Therefore, in this study, development and experiments were conducted so that the robot could perform real-time monitoring at the disaster site. Multi-sensor module was developed by combining LiDAR, Inertial Measurement Unit (IMU) sensor, and computing board. Then, this module was mounted on the robot, and a customized Simultaneous Localization and Mapping (SLAM) algorithm was developed. A method for stably mounting a multi-sensor module to a robot to maintain optimal accuracy at disaster sites was studied. And to check the performance of the module, SLAM was tested inside the disaster building, and various SLAM algorithms and distance comparisons were performed. As a result, PackSLAM developed in this study showed lower error compared to other algorithms, showing the possibility of application in disaster sites. In the future, in order to further enhance usability at disaster sites, various experiments will be conducted by establishing a rough terrain environment with many obstacles.