• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.2
• /
• pp.115-122
• /
• 2016

In this paper, wideband Ku-band downconverter was designed to receiver digital satellite broadcasting. The low-nose downconverter was designed to form four local oscillator frequencies(9.75, 10, 10.75 and 11.3 GHz) representing a low phase noise due to VCO-PLL with respect to input signals of 10.7 to 12.75 GHz and 3-stage low noise amplifier circuit by broadband noise matching, and to select intermediate frequency bands by digital control. The developed low-noise downconverter exhibited the full conversion gain of 64 dB, and the noise figure of low-noise amplifier was 0.7 dB, the P1dB of output signal 15 dBm, and the phase noise -85 dBc@10kHz at the band 1 carrier frequency of 9.75 GHz. The low noise block downconverter(LNB) for wideband digital satellite broadcasting designed in this paper can be used for global satellite broadcasting LNB.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.23 no.8
• /
• pp.959-965
• /
• 2019

In this paper, we design a low noise amplifier to support ka-band satellite communication systems using 65-nm RFCMOS process. The proposed low noise amplifier is designed with high-gain mode and low-gain mode, and is designed to control the gain according to the magnitude of the input signal. In order to reduce the power consumption, the supply voltage of the entire circuit is limited to 1 V or less. We proposed the gain control circuit that consists of the inverter structure. The 3D EM simulator is used to reduce the size of the circuit. The size of the designed amplifier including pad is $0.33mm^2$. The fabricated amplifier has a -7 dB gain control range in 3 dB bandwidth and the reflection coefficient is less than -6 dB in high gain mode and less than -15 dB in low gain mode.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.21 no.3
• /
• pp.29-34
• /
• 2021

For the purpose of Application to the small radar sensor, the MMIC Chips, which are the core component of the W-band, was designed in Korea according to the characteristics of the transceiver and manufactured by 60nm GaN and 0.1㎛ GaAs pHEMT process. The output power of PA is 28 dBm at center frequency of W-band and Noise figure is 6.7 dB of switch and LNA MMIC. Output power and Noise figure of MMIC chips developed in domestic was applied to the transmitter and receiver module through W-band waveguide low loss transition structure design and impedance matching to verify the performance after the fabrication are 26.1~27.7 dBm and 7.85~10.57 dB including thermal testing, and which are close to the analysis result. As a result, these are judged that the PA and Switch and LNA MMICs can be applied to the small radar sensor.

• Ceramist
• /
• v.22 no.4
• /
• pp.350-356
• /
• 2019

Recently, transition metal dichalcogenide (TMDC) monolayers have been the subject of research exploring the physical phenomenon generated by low dimensionality and high symmetry. One of the keys to understanding new physical observations is the electronic band structure of 2D TMDCs. Angle-resolved photoelectron spectroscopy (ARPES) is, to this point, the best technique for obtaining information on the electronic structure of 2D TMDCs. However, through ARPES research, obtaining the long-range well-ordered single crystal samples always proves a challenging and obstacle presenting issue, which has been limiting towards measuring the electronic band structures of samples. This is particularly true in general 2D TMDCs cases. Here, we introduce the approach, with a mathematical framework, to overcome such ARPES limitations by employing the high level of symmetry of 2D TMDCs. Their high symmetry enables measurement of the clear and sharp electronic band dispersion, which is dominated by the band dispersion of single-crystal TMDCs along the two high symmetry directions Γ-K and Γ-M. In addition, we present two important studies and observations for the direct measuring of the exciton binding energy and charge transfer of 2D TMDCs, both being established by the above novel approach.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.6
• /
• pp.72-80
• /
• 1996

This paper presetns the development of a SSPA operating at KU-band(14~14.5 GHz) in order of replace TWTA used in the terrestria transponder of a satellite communication. The driving stage of SSPA uses internally matched 2W, 4W, 8W FET and the power stage is coupled with two internally matched 8W FET by branch-line cominer. The SSPA is fabricated with oth the RF circuit and the bias circuitry operating temperature compensation, regulation and sequence on aluminum housing. The SSPA testing resutls implemented in this way show 24.8$\pm$1dB small-signal gain, 41dBm P1dB power, a typical two tone C/IM3, -33dBc with single carrier backed off 6dB from p1dB, and gain stability over temeprature (-30~50)$\pm$1dB.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.15 no.2
• /
• pp.276-279
• /
• 2015

This paper presents two 3-stage D-band stacked amplifiers developed in a $0.13-{\mu}m$ SiGe BiCMOS technology, employed to compare the conventional cascode topology and the common-base (CB)/CB stacked topology. AMP1 employs two cascode stages followed by a CB/CB stacked stage, while AMP2 is composed of three CB/CB stacked stages. AMP1 showed a 17.1 dB peak gain at 143.8 GHz and a saturation output power of -4.2 dBm, while AMP2 showed a 20.4 dB peak gain at 150.6 GHz and a saturation output power of -1.3 dBm. The respective power dissipation was 42.9 mW and 59.4 mW for the two amplifiers. The results show that CB/CB stacked topology is favored over cascode topology in terms of gain near 140 GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.2
• /
• pp.147-153
• /
• 2009

In this paper, FSS(Frequency Selective Surface) using defect mode characteristic is proposed. The unit cell using defect mode characteristic of the proposed FSS is offered lower resonant frequency in the same cell size. The number of suitable array is optimized 13 by 13. Also, the patch antennas operated in WCDMA(Wideband Code Division Multiple Access) Tx band and Rx band are designed for the comparison. The gain value of proposed FSS-1 complex structure (the patch antenna of Tx band and FSS) is improved 3.3 dB from 9.98 dBi to 13.28 dBi in Tx band. The gain value of proposed FSS-2 complex structure(the patch antenna of Rx band and FSS) is improved 5.53 dB from 9.81 dBi to 15.34 dBi in Rx band. Also the measured impedance bandwidth($VSWR{\leq}2$) of manufactured $13{\times}13$ array antenna is from 337 MHz(1.87 to 2.21 GHz). The measured radiation gain is 11.39 dBi(1.94 GHz), 13.11 dBi(2.05 GHz), 11.09 dBi(2.14 GHz). The measured radiation efficiency is 81 %. Because the proposed FSS structure has more higher gain, it will be applied to antenna of WCDMA repeater system.

• Advances in nano research
• /
• v.9 no.2
• /
• pp.105-112
• /
• 2020

Silicene is a two-dimensional (2D) derivative of silicon (Si) arranged in honeycomb lattice. It is predicted to be compatible with the present fabrication technology. However, its gapless properties (neglecting the spin-orbiting effect) hinders its application as digital switching devices. Thus, a suitable band gap engineering technique is required. In the present work, the band structure and density of states of uniformly doped silicene are obtained using the nearest neighbour tight-binding (NNTB) model. The results show that uniform substitutional doping using aluminium (Al) has successfully induced band gap in silicene. The band structures of the presented model are in good agreement with published results in terms of the valence band and conduction band. The band gap values extracted from the presented models are 0.39 eV and 0.78 eV for uniformly doped silicene with Al at the doping concentration of 12.5% and 25% respectively. The results show that the engineered band gap values are within the range for electronic switching applications. The conclusions of this study envisage that the uniformly doped silicene with Al can be further explored and applied in the future nanoelectronic devices.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.7
• /
• pp.1267-1271
• /
• 2009

In this paper, a diplexer circuit to separate GSM from CDMA band is designed using a LTCC (Low Temperature Cofired Ceramic) multi-layer technology. In order to increase a integration capability of the diplexer, it is designed using 3-dimensional (3-D) multi-layer compact inductor and capacitors in e-layer LTCC substrate with a relative dielectric constant of 7. In order to achieve high selectivity of the bands, a shunt capacitor and inductor are designed in the high-pass filter (HPF) and low-pass filter (LPF), respectively. The size of the fabricated diplexer including CPW pads is 3,450 ${\times}$4,000 ${\times}$694 ${\mu}m^3$An insertion loss (IL) and return loss in GSM band are less than -1.35dB and more than -5.66dB,respectively. In the case of CDMA band, the IL of -1.54dBandRLof above -9.30dBare archived.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.1
• /
• pp.1-16
• /
• 1996

In this paper, by combining the motion compensated transform coding with the sub-band decomposition technique, we present a motion compensated sub-band coding technique(MCSBC) for image sequence coding. Several problems related to the MCSBC, such as a scheme for motion compensation in each sub-band and the efficient VWL coding of the DCT coefficients in each sub-band are discussed. For an efficient coding, the motion estimation and compensation is performed only on the LL sub-band, but the discrete cosine transform(DCT) is employed to encode all sub-bands in our approach. Then, the transform coefficients in each sub-band are scanned in a different manner depending on the energy distributions in the DCT domain, and coded by using separate 2-D Huffman code tables, which are optimized to the probability distributions in the DCT domain, and coded by using separate 2-D Huffman code tables, which are optimized to the probability distribution of each sub-band. The performance of the proposed MCSBC technique is intensively examined by computer simulations on the HDTV image sequences. The simulation results reveal that the proposed MCSBC technique outperforms other coding techniques, especially the well-known motion compensated transform coding technique by about 1.5dB, in terms of the average peak signal to noise ratio.