This paper presents the design approach and test results of the Q-band precision subminiature coaxial adaptor based on transmission line theory using multi-step impedance and air-holes to increase its cutoff frequency. In order to increase the frequency performance, the adaptor is designed with hooked structure, fixing step, multi-air-holes, and outer conductor. The return loss increments due to the hooked structure and multi air-holes are minimized to 2 dB and 1.5 dB, respectively. A VSWR(Voltage Standing Wave Ratio) of <1.2 is obtained from DC to 40 GHz, while guaranteeing the durability of the adaptor from room-temperature$(25^{\circ}C)$ to $120^{\circ}C$.
본 논문은 wireless LAN 주파수 대역 (5725∼5825 MHz)에서의 다차원패턴기술(Photonic Band Gap : PBG)을 이용한 Yagi-Uda 안테나와 결합하여 광대역 마이크로스트립 패치 안테나를 구현하였으며, PBG Cell을 이용한 안테나와 이용하지 않은 안테나를 비교 분석하였다. PBG 구조를 적용한 안테나에서의 대역폭이 약 30 MHz 정도 더 넓게 나왔으며, 안테나의 이득 또한 1dB정도 더 높게 나왔는데 이는 Ground 면에 2차원적인 다차원 패턴 구조를 적용하여 안테나 표면을 따라 전파하는 전자파의 전송이 억제되도록 표면파의 발생을 효과적으로 차단했기 때문으로 분석된다.
JSTS:Journal of Semiconductor Technology and Science
/
제3권1호
/
pp.42-46
/
2003
In this paper, an MMIC broadband amplifier for wireless communication systems has been developed by using an active feedback method. This active feedback operates at much higher frequencies than a method by a spiral inductor feedback and its size is independent of the inductance value. The MMIC broadband amplifier was designed using a $0.5{\;}{\mutextrm{m}}$ MESFET library. The fabricated chip area was $1.4{\;}mm{\;}{\times}{\;}1.4{\;}mm. Measurement showed a gain of 18 dB with a gain flatness of ${\pm}3$ dB in a 1.5 GHz~3.5 GHz band. The maximum output power and the minimum noise figure were 14 dBm and 2.5 dB in the same band, respectively.
This paper presents millimeter wave monolithic microwave integrated circuit (MMIC) low noise amplifiers using a $0.15{\mu}m$ commercial pHEMT process. After carefully investigating design considerations for millimeter-wave applications, with emphasis on the active device model and electomagnetic (EM) simulation, we designed two single-ended low noise amplifiers, one for Q-band and one for V-band. The Q-band two stage amplifier showed an average noise figure of 2.2 dB with an 18.3 dB average gain at 44 GHz. The V-band two stage amplifier showed an average noise figure of 2.9 dB with a 14.7 dB average gain at 65 GHz. Our design technique and model demonstrates good agreement between measured and predicted results. Compared with the published data, this work also presents state-of-the-art performance in terms of the gain and noise figure.
The purpose of this study is to develop the miniaturized duplexer filter for mobile communications using high dielectric constant (${\varepsilon}$r > 100, 180) ceramic resonators. Duplexer filter was ocmposed of ceramic resonators which has been developed using BNT system and SCT system, respectively. Developed duplexer filter was formed to have Tx frequency band at 836.5 (($\pm$12.5)MHz and Rx frequency band at 881.5 ($\pm$12.5)MHz. Insertion loss at Tx frequency band was 1.41dB and 1.46dB, insertion loss at Rx frequency band was 3.49dB and 3.65dB, respectively. Especially, duplexer filters using dielectric cermaics with ${\varepsilon}$r = 180 were 8% smaller than commercially manufactured duplexer filters using dielectric ceramics with ${\varepsilon}$r = 90 by murata.
Abroad-band design method of a lumped-element 3 dB quadrature hybrid without magnetic coupling is proposed and discussed, where techniques of cascading fundamental hybrids via second-order delay equializers and adding matching sections are adopted. It is shown that the designed broad-band lumped-element 3 dB quadrature hybrid can be easily constructed and its bandwidth reaches up to 54%. Furthermore, the experiments have been carried out, the results of which agree with the theoretical ones, and hence, the validity of the broad-band design method proposed here was confirmed.
본 논문에서는 RF 에너지 충전 시스템 기능이 가능한 이중대역 RFID 태그 안테나(Tag antenna)를 제안한다. 제안된 안테나는 UHF 대역과 Microwave 대역에서 각각 수동형과 능동형의 RFID 태그 안테나로 동작을 한다. 또한 능동형으로 동작하는 Microwave 대역 RFID 태그의 제한된 배터리 용량을 보충하기 위하여 수동형 태그로 동작하는 UHF 대역의 RFID 태그를 위한 RF 신호를 충전 회로에 적용 가능한 이중대역 RFID 태그 안테나의 특징을 가진다. 제안된 안테나는 UHF 대역 (917~923.5 MHz)과 Microwave 대역 (2.4~2.45 GHz)에서 동작을 위한 $50{\Omega}$의 단일급전이 이용된 다이폴(Dipole) 구조와 미앤더(Meander) 기생 소자들을 이용한 ${\lambda}/2$ 다이폴과 $1{\lambda}$ 다이폴로 각각 동작하는 이중대역 안테나의 특징을 가진다. 다이폴 구조는 Microwave 대역에서 동작을 하며, 다이폴 구조에 추가된 미앤더 기생 소자와 함께 UHF 대역에서 동작을 한다. 즉, Microwave 대역에 대하여 동작하는 다이폴 구조는 UHF 대역에서 동작을 위한 기생 소자들의 간접급전의 역할을 한다. 제작된 안테나는 UHF 대역의 917~923.5 MHz와 Microwave 대역의 2.4~2.45 GHz의 대역에 대하여 VSWR 2:1 이하를 만족하며, 또한 전방향적인 방사패턴 (Omni-directional radiation pattern)을 가진다. 안테나의 효율은 UHF 대역에서 45 % 이상, Microwave 대역에서 70 % 이상이며, 각각의 대역에서 0.18 dBi, 2.8 dBi 이상의 최대 이득을 가진다.
본 논문에서는 밀리미터파 탐색기에 사용되는 Ka-대역 수신기 모듈 설계 및 제작 기법을 제시하였다. 수신기 모듈은 안테나 연결을 위한 도파관, 순환기(Circulator) 및 모드 변환기, 수신기 보호를 위한 리미터 및 이득 제어 증폭기를 포함한다. 또한 모노 펄스 수신을 위한 합, 고각 및 방위각 채널로 구성되며 재밍 신호 확인을 위한 SLB(Sidelobe Blankin) 채널로 구성된다. 본 논문에서는 ADC(Analog to Digital Converter)의 비선형 특성에 따른 수신기 이득 및 이득 제어 범위를 분석하고, 넓은 수신기 동작 영역을 가지도록 설계되었다. 제작된 Ka-대역 수신기 측정 결과, 주파수 대역은 1 GHz, 잡음 지수는 8.2 dB 이하, 이득은 $56{\pm}2dB$, 동적 영역은 135 dB, 이득 제어 86 dB 이상, 채널간 격리도 35 dB 이상이다.
본 논문에서는 InGaAs enhancement mode $0.15{\mu}m$ pHEMT를 이용하여 6~10 GHz 대역에서 동작하는 wide-band 전력증폭기를 설계하였다. Enhancement 소자는 gate 바이어스를 양전압으로 사용하며, 음전압을 위한 추가회로 구성이 없어지며 모듈의 크기를 줄일 수 있다. 또한, 본 설계에서는 3D-EM(electromagnetic) 시뮬레이션을 통해 패키지 본드와이어의 인덕턴스 및 기판 손실을 예측하여 설계하였다. 광대역을 위해 lossy matching을 사용하고, 전력, 효율 관점에서 최적의 바이어스를 선정하여 설계하였다. 제안한 전력증폭기의 패키지 칩은 6~10 GHz 대역에서 20 dB 이상의 평탄 이득, 8 dB 이상의 입출력 반사손실, 출력전력은 27 dBm 이상, 전력부가효율은 35 % 이상으로 측정되었다.
본 논문에서 는 Ka-band 위 성 중계 기용 국부발진기 의 EM(Engineering Model)을 설계 및 제작하였다. 루프 대역 밖의 위상잡음을 개선하기 위해서 고임피던스 변환기를 이용한 낮은 위상잡음의 전압제어 발진기를 설계하고 샘플링위상비교기(Sampling Phase Detector)를 사용하여 전압제어 발진기를 고안정의 OCXO(Oven Controlled Crystal Oscillator)에 위상 고정시킴으로써 루프 대역 내의 위상잡음을 개선하였다. 개발된 국부발진기는 43.83 dBc 이상의 고조파 억압특성을 가지고 있으며 공급전력은 15 V, 160 mA를 필요로 한다. 위상잡음은 -102.5 dBc/Hz @10 KHz와 -104.0 dBc/Hz @100 KHz의 특성을 나타내며 출력전력은 -20 - +7$0^{\circ}C$의 온도 범위에서 13.50 dBm$\pm$0.33 dB의 특성을 얻었다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.