• 드라이브 ㆍ 컨트롤
• /
• 제11권4호
• /
• pp.53-60
• /
• 2014

This paper proposes a control scheme to reduce the power consumption of a variable displacement swash-plate type piston pump supplying oil to a valve-controlled hydraulic cylinder at constant pressure. Whenever flow rate demand was absent, the swash plate angle and the pump speed were changed to the minimum values required to compensate for the internal leakage flow. In response to command signals, the pump speed was changed in proportion to the absolute mean value of the speed component for position commands. At the same time, a pressure regulator was activated to maintain constant system pressure by precisely adjusting the pump speed with the swash plate angle fixed at the maximum. The conventional system consisting of a pressure-compensated variable displacement type pump is driven at a constant speed of 1,800rpm. By comparison, computer simulation and experimental results showed that idling power at stand-by status could be reduced by up to 70% by reducing the pump speed from 1,800rpm to 300rpm and the swash plate angle to the minimum.

• 선박안전
• /
• 통권23호
• /
• pp.78-97
• /
• 2007

SPM, which is an abbreviation of Single Point Mooring, also called as SBM(Single Buoy Mooring), is a special buoy besides the quays of the harbor for mooring ships, and is normally a 3m wide cone or cylinder shaped steel drum fixed underwater so it won't move, and is used for mooring cargo-work at outer port by laid-up ships and large crude oil carrier. The work of VLCC SPM mainly is accomplished on the open sea. On the open sea as a result of meteorological condition and the ocean wave influence, When the weather condition is get bed, peremptorily moving to the safety place, because of the gale and the billow, almost happened frequently, the pilot is unable to go on board and the tug is also unable to be used Now because of the bad weather the VLCC SPM moving to the other safety place frequently happened in the ulsan port. the construction of new harbor, it constructed many break water around SPM. So that it is necessary to propose the new standard about how to maneuvering area actually. The standard for handling ranges of the SPM operations was tested and verified by a simulation.. So that it is necessary to propose the new standard about how to maneuvering area actually.

• Journal of Computational Design and Engineering
• /
• 제1권1호
• /
• pp.13-26
• /
• 2014

Recently, renovations of plant equipment have been more frequent because of the shortened lifespans of the products, and as-built models from large-scale laser-scanned data is expected to streamline rebuilding processes. However, the laser-scanned data of an existing plant has an enormous amount of points, captures intricate objects, and includes a high noise level, so the manual reconstruction of a 3D model is very time-consuming and costly. Among plant equipment, piping systems account for the greatest proportion. Therefore, the purpose of this research was to propose an algorithm which could automatically recognize a piping system from the terrestrial laser-scanned data of plant equipment. The straight portion of pipes, connecting parts, and connection relationship of the piping system can be recognized in this algorithm. Normal-based region growing and cylinder surface fitting can extract all possible locations of pipes, including straight pipes, elbows, and junctions. Tracing the axes of a piping system enables the recognition of the positions of these elements and their connection relationship. Using only point clouds, the recognition algorithm can be performed in a fully automatic way. The algorithm was applied to large-scale scanned data of an oil rig and a chemical plant. Recognition rates of about 86%, 88%, and 71% were achieved straight pipes, elbows, and junctions, respectively.

• Tribology and Lubricants
• /
• 제16권3호
• /
• pp.223-230
• /
• 2000

Molybdenum dialkyl dithiophosphate(MoDTP) 마찰특성을 이원통 마찰시험기에 의한 마찰실험 및 X-선광전자분광분석기를 이용하여 마찰표면을 분석함으로써 MoDTP의 마찰감소 작용에 대해 고찰하였다 MoDTP의 마찰감소작용은 마찰표면에 생성하는 MoS$_2$에 의존하였다. 몰리브덴(Mo)이 용이하게 금속내부로 확산하는 질소분위기 중에서는 MoDTP의 마찰감소 특성은 나타나지 않았으며, 금속표면에 산화피막이 존재할 때 MoDTP의 마찰감소작용이 잘 나타남을 알 수 있었다

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제13권1호
• /
• pp.659-673
• /
• 2021

This study aims to investigate the impact of the High Pressure Selective Catalytic Reduction system (SCR-HP) on a large marine two-stroke engine performance parameters by employing thermodynamic modelling. A coupled model of the zero-dimensional type is extended to incorporate the modelling of the SCR-HP components and the Control Bypass Valve (CBV) block. This model is employed to simulate several scenarios representing the engine operation at both healthy and degraded conditions considering the compressor fouling and the SCR reactor clogging. The derived results are analysed to quantify the impact of the SCR-HP on the investigated engine performance. The SCR system pressure drop and the cylinder bypass valve flow cause an increase of the engine Specific Fuel Oil Consumption (SFOC) in the range 0.3-2.77 g/kWh. The thermal inertia of the SCR-HP is mainly attributed to the SCR reactor, which causes a delayed turbocharger response. These effects are more pronounced at low engine loads. This study supports the better understanding of the operating characteristics of marine two-stroke diesel engines equipped with the SCR-HP and quantification of the impact of the components degradation on the engine performance.

• 한국음향학회지
• /
• 제30권1호
• /
• pp.33-41
• /
• 2011

음압을 감지할 수 있는 Sagnac 간섭계 센서와 온도 및 스트레인을 측정할 수 있는 FBG센서를 결합한 새로운 형태의 하이브리드 광섬유 센서 시스템을 구축하기 위하여 입력 광원인 CW를 TLS로 대체할 필요가 있어 이에 따라 광원의 변화와 맨드릴 재료의 변화에 따른 광섬유 센서의 응답 특성 연구가 필요하게 되었다. 제작된 맨드릴 재료는 PTFE와 PTFE에 카본을 섞어 만든 두 종류로 선택하여 중공 원통형 맨드릴 겉면에 광섬유를 18 m 감아 광섬유 센서로 제작하였다. CW 광원에 대하여 음원의 입력 주파수를 1 kHz~20 kHz까지 바꾸어 가며 트랜스포머 오일이 채워진 유조에서 실험하였다. 또한 FBG와 맨드릴형 광섬유 센서를 결합한 하이브리드형 광섬유 센서 시스템을 구성하고 TLS 광원을 입사광으로 실험하였다. 실험 결과 PTFE 센서의 탐지 크기는 카본 센서 탐지 크기보다 높게 나타났고 맨드릴 재질의 탄성계수 값이 적을수록 커진다는 이론 결과와 잘 일치함을 보였다. CW 광원과 TLS 광원에서 응답한 PTFE 센서의 특성을 주파수별로 상호 비교하여 보면 광원이 CW일 때 보다 TLS일 때 응답 특성이 우수함을 알 수 있었다. 본 연구를 통하여 TLS를 이용한 광섬유 센서는 FBG와의 하이브리드 시스템에 적용 가능하리라 사료된다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제39권5호
• /
• pp.542-547
• /
• 2015

Since the oil price has been significantly jumped for several years, a heavy oil of low quality has been mainly used in the diesel engine of the merchant ship. Thus, a combustion chamber of the engine has been often exposed to severely corrosive environment more and more because temperature of the exhaust gas of the combustion chamber has been getting higher and higher with increasing of using the heavy oil of low quality. As a result, wear and corrosion of the engine parts such as exhaust valve, piston crown and cylinder head surrounded with combustion chamber are more serious compared to the other parts of the engine. Therefore, an optimum repair welding for these engine parts is very important to prolong their lifetime in a economical point of view. In this study, Inconel 625 filler metal were welded with GTAW method in the cast steel which would be generally used with piston crown material. And the corrosion properties of weld metal, heat affected and base metal zones were investigated using electrochemical methods such as measurement of corrosion potential, anodic polarization curves, cyclic voltammogram and impedance etc. in 35% $H_2SO_4$ solution. The weld metal and base metal zones exhibited the highest and lowest values of hardness respectively. Furthermore, the corrosion current density of the weld metal zone revealed the lowest value, having the highest value of hardness. The corrosive products with red color and local corrosion like as a pitting corrosion were considerably observed at the base metal zone, while these morphologies were not wholly observed in the weld metal zone. In particular, the polarization characteristics such as impedance, polarization curve and cyclic voltammogran associated with corrosion resistance property were well in good agreement with each other. Consequently, it is suggested that the mechanical and corrosion characteristics of the piston crown can be predominantly improved by repair welding method using the Inconel 625 electrode.

• Journal of Advanced Marine Engineering and Technology
• /
• 제38권7호
• /
• pp.868-876
• /
• 2014

본 논문에서는 함정에 탑재된 추진용 엔진에 사용되는 디젤연료(MDO)의 분사상태를 가시화가 가능한 단기통 디젤엔진에 적용시켜 전 후 분사시기에 따른 연소특성, 일산화탄소(CO) 및 탄화수소(HC) 배출특성을 규명하고, 연소과정의 가시화를 통하여 연소특성을 분석하는데 초점을 두었다. 전 분사시기가 주 분사시기 쪽으로 지연될수록 실린더 내부 평균유효압력($P_{me}$) 및 최고압력($P_m$)은 상승했으나, 주 분사의 방열율은 저감되고, 일산화탄소 및 탄화수소의 발생량 또한 감소하였다. 후 분사시기가 빨라질 경우 주 분사에 의해 형성된 고온, 고압 하에서 연소가 이루어짐에 따라 실린더 내부 평균유효압력 및 최고압력은 증가하였고, 일산화탄소 및 탄화수소 배출수준 또한 증가하였다. 연소과정을 분석한 결과, 전 분사시기가 늦어질수록 주 분사 시 발생되는 착화지연은 매우 짧아지며, 화염강도는 매우 상승하였다. 분사시기에 관계없이 후 분사 시 착화지연 현상은 발생하지 않았으며, 후 분사시기가 늦어질수록 화염의 강도는 점점 떨어졌다.

• 한국해양공학회지
• /
• 제33권4호
• /
• pp.350-357
• /
• 2019

The development of marine technology is expected to increase the demand for marine plants because of increasing oil prices. Therefore, there is also expected to be an increase in the demand for cylindrical structures such as URF (umbilical, riser, flowline) structures and spars, which are used operating in various seas. However, a cylindrical structure experiences vortex induced motion (VIM) in a current. In particular, for risers and umbilicals, it is important to identify the characteristics of the VIM because interference between structures can occur. In addition, various studies have been conducted to reduce VIM because it is the cause of fatigue damage to structures. The helical strake, which was developed for VIM reduction, has an excellent VIM reduction performance, but is difficult to install on structures and has a negative effect on heave motion. Therefore, the purpose of this study was to supplement the shortcomings of the helical strake and develop a high-performance reduction device. In the reduction device developed in this study, a string is placed around the structure inside the flow, causing vibration. The vibration of this string causes a small turbulence in the flow field, reducing the VIM effect on the structure. Finally, in this study, the 2-DOF motion characteristics of models without a suppression device, models with a helical strake, and models with a string were investigated, and their reduction performances were compared through model tests.

• International Journal of Automotive Technology
• /
• 제6권1호
• /
• pp.15-21
• /
• 2005

The purpose of this paper is to experimentally investigate the engine pollutant emissions and combustion characteristics of diesel engine fueled with ethanol-diesel blended fuel (bio-diesohol). The experiments were performed on a single-cylinder DI diesel engine. Two blend fuels were consisted of $15\%$ ethanol, $83.5\%$ diesel and $1.5\%$ solublizer (by volume) were evaluated: one without cetane improver (E15-D) and one with a cetane improver (E15-D+CN improver). The engine performance parameters and emissions including fuel consumption, exhaust temperature, lubricating oil temperature, Bosch smoke number, CO, NOx, and THC were measured, and compared to the baseline diesel fuel. In order to gain insight into the combustion characteristics of bio-diesohol blends, the engine combustion processes for blended fuels and diesel fuel were observed using an Engine Video System (AVL 513). The results showed that the brake specific fuel consumption (BSFC) increased at overall engine operating conditions, but it is worth noting that the brake thermal efficiency (BTE) increased by up to $1-2.3\%$ with two blends when compared to diesel fuel. It is found that the engine fueled with ethanol-diesel blend fuels has higher emissions of THC, lower emissions of CO, NOx, and smoke. And the results also indicated that the cetane improver has positive effects on CO and NOx emissions, but negative effect on THC emission. Based on engine combustion visualization, it is found that ignition delay increased, combustion duration and the luminosity of flame decreased for the diesohol blends. The combustion is improved when the CN improver was added to the blend fuel.