• Magazine of the Korean Society of Agricultural Engineers
• /
• v.40 no.5
• /
• pp.43-51
• /
• 1998

In design and management of sea0dikes, engineers need to study various transient seepage conditions through dikes not only for the sea water infiltration into dikes due to cyclic rises of sea water level also for the seepage flow out from dikes toward the sea due to cyclic drawdown of sea water level. Characteristics of seepage flow toward the sea from dikes are more complicated than as known and remained unclearly. The case of such seepage flow may be explained by figuring out seepage characteristics in filter as a part of sea-dikes. Filters in most sea-dikes in Korea are inevitably placed with reversely inclined shape due to field construction conditions. Most computer programs for seepage analysis based on the various numerical methods give practically acceptable results, but for the case of reversely inclined section of filters any verification to apply them might be needed. In this study, large scaled model tests were executed to verify and understand seepage flow through earth-filled sea-dikes. The results from numerical analysis and model tests show some remarkable differences in pore pressure distribution under cyclic changes of see level, and some of the results need to be considered in design and construction practices with further study.

• Geotechnical Engineering
• /
• v.2 no.1
• /
• pp.55-66
• /
• 1986

Considering the effects of confining pressure, initial shear stress, cyclic stress ratio and number of loading cycles, cyclic triaxial tests are carried out to clarify the soil dynamic properties such as shear modulus and value of material damping of clay under undrained cyclic loading conditions. The results show that no obvious dependency on initial shear stress and effective confining stress are recognized in the shear modulus and damping ratio plotted versus strain. However, the shear modulus decreases and the damping ratio increases with increasing axial strain. When compared with others, it is also revealed that the shear moduli are distributed within the range curves obtained using empirical equations derived by Marcuson et al. (3) and Kokusho et al. (4), and damping ratios are distributed between the curves obtained by Kokusho et al. (4) and Ishihara et al. (9).

• Journal of the Earthquake Engineering Society of Korea
• /
• v.28 no.1
• /
• pp.67-75
• /
• 2024

In the case of the Pohang earthquake, which had a magnitude of 5.4 in 2017, geotechnical damages such as liquefaction and ground settlement occurred. The need for countermeasures has emerged, and experimental research in the Pohang area has continued. This study collected undisturbed samples from damaged fine-grained soil areas where ground settlement occurred in Pohang. Cyclic tri-axial tests for identifying the dynamic characteristics of soils were performed on the undisturbed samples, and the results were analyzed to determine the cause of ground settlement. As a result of the study, it was determined that in the case of fine-grained soils, ground settlement occurred because the seismic load as an external force was relatively more significant than the shear resistance of the very soft fine-grained soils, rather than due to an increase in excess pore water pressure.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2002.03a
• /
• pp.67-74
• /
• 2002

An experimental assessment on the dynamic behavior of saturated sand which can consider the irregular characteristics of earthquakes was proposed. The equivalent uniform stress concept presented by Seed and Idriss has been applied to evaluate the liquefaction resistance strength to simplify earthquake loading. However, it was known that the liquefaction resistance strength of soil based on the equivalent uniform stress concept can't exactly mirror the dynamic characteristics of the irregular earthquake motion. In this study, estimation of the criterion of the liquefaction resistance strength was determined by applying real earthquake loading to the cyclic triaxial test. From the test results, relationships between excess pore water pressure and the earthquake characteristics such as magnitude or duration were determined. Magnitude scaling factors to determine the soil liquefaction resistance strength in seismic design were also proposed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.2 no.1
• /
• pp.51-64
• /
• 1994

Analytical study on the thermodynamical cyclic behabiour and characteristics of HFC-l34a refrigerant for automotive air conditionser system for the replacement of existing CFC-12 has been carried out in this paper through development of system performance simulation program, expecially in the view point of system design considerations. The results indicate that HFC-l34a system will give a greater refrigerating capacity than CFC-12 if appropriate engineering measures such as proper codensers, flow controllers, etc., taken for certain operating conditions. The results, however, also show that the operating power for compression process increases over entire temperature range as a result of decreasing volumetric efficiency due to larger specific volume and increased discharging pressure. The present study results indicate that proper selection of condensing and evaporating temperature plus refrigerant control is very important performance factor to have better COP in the HFC-134a system design.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.752-755
• /
• 2002

Since Metallo-Porphyrin (MP) is very interesting compound due to its unique electronic and redox properties and it is also chemically and thermally stable, MP has been studied for potential memory and switching devices. In this study, thin films of 5,10,15,20 - Tetrakis - Octadecyloxymethylphenyl - Porphyrin - Zn(II) (Zn-TPP) were prepared by the Langmuir-Blodgett (LB) method and characterized by using UV/vis absorption spectroscopy and cyclic voltammetry. It was found that the proper transfer surface pressure for film deposition was 25 mN/m and the limiting area per molecule was $135{\AA}^2$/molecule. The current-voltage (I-V) characteristics of these films were investigated.

• Journal of Power System Engineering
• /
• v.14 no.4
• /
• pp.37-42
• /
• 2010

This paper deals with the sealing mechanism of the gasket component and the effects of design parameters for the exhaust manifold. The finite element model includes hot-end exhaust system and a simplified gasket model supplied by ABAQUS software. The mechanical behaviors of bead and body of a gasket are measured after several times of cyclic loads by gasket supplier. From the finite element analysis due to the cyclic thermal loads, the flange of exhaust manifold shows thermal expansion and contraction in longitudinal direction as well as convex and concave deformations with respect to the engine cylinder head. And, the contact pressures of the gasket beads suddenly changes by normal deformation of inlet flanges. Therefore, the magnitudes of contact pressures could be used to determine the sealing characteristics of the exhaust gas in the exhaust system. The distributions of contact pressures in gasket bead lines shows a good agreement with the engine test results.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.12
• /
• pp.1647-1655
• /
• 1997

The cyclic variations can be characterized by the variations in different type of parameters. These parameters may be grouped into four main categories: pressure-related parameters, combustion-related parameters, flame front-related parameters, and exhaust gas-related parameters. One of the resultant effects of the cycle-by-cycle variation in the combustion process, which is the most important with regard to the engine performance characteristics, is the cycle-by-cycle variation in IMEP. This paper uses the repetitive discharge igniter, which can change the ignition energy easily, to study on idle stability in a spark ignition engine. From this device, the 6 number of spark and 0.20 ms spark interval, it is very available for the idle stability.

• Journal of the Korean Vacuum Society
• /
• v.8 no.2
• /
• pp.127-135
• /
• 1999

Nickel oxide films were prepard by using the electron beam evaporation technique. Coloring and bleaching experiments for cyclic durability were repeated in KOH electrolyte by cyclic voltammetry. Visible spectrophtometry was used to assess the stability of the transmittance in the degraded films. X-ray photoelectron spectroscopy results showed that the grain surface are oxygen-rich compared to the grain interiors in a NiO film. Open circuit memory of colored films is about 400hours in lN KOH. The rate of self discharge was evaluated by measuring the transmittance at 550nm of a fully oxidized NiO film. The rate of self discharge was increased polynomially with time and the film is nearly bleached after about 400hours. It was also found that the degraded film by repeated cycles in the KOH solution changed the grain shape of film surface The film prepared under a vacuum pressure of $3\times10^{-4}$ mbar was found to be rather stable when subjected to the repeated coloring and bleaching cycles in KOH electrolyte. Band theory applied to explain the electrochromic mechanism was discussed.

• Earthquakes and Structures
• /
• v.7 no.5
• /
• pp.753-777
• /
• 2014

This study investigates the behavior of precast concrete cantilever wall systems with new vertical connections under cyclic loading. C-type steel connections for PC wall systems are proposed for the transfer of bending moments between walls in the vertical direction, whereas a shear key in the center of the wall is prepared to transfer shear forces by bearing pressure. The proposed connections are assembled easily because the directions of the slots are different at the edges of the walls. Structural performance characteristics such as the strength, ductility, and failure modes of test specimens were investigated. The longitudinal reinforcing steel bars, which are connected to the C-type connections, yielded first. Ultimate deformation was terminated owing to premature failure of the connections. The strength and deformation obtained from the cross-sectional analysis were generally similar to experimental data.