• 전기화학회지
• /
• 제10권2호
• /
• pp.145-149
• /
• 2007

본 논문은 마이크로전극 측정시스템을 사용하여 니켈수소전지의 전극 소재로 사용되고 있는 수산화니켈의 단일 입자에 대해 전기화학적 평가를 수행 하였다. 즉 Carbon fiber 마이크로전극을 수산화니켈 입자 한개 위에 전기적인 접촉을 이루도록 조정하고 전기화학적 평가를 수행하였다. Cyclic Voltammetry 실험 결과 수산화니켈의 산화 환원 반응과 산소 발생 반응(OER)이 명확하게 분리 되고 있음을 확인하였으며, 전위주사속도를 증가 시킬 경우 환원 전하량은 주사 속도에 의존하지 않고 거의 일정한 수치를 보여 주고 있으나, 산화 전하량은 환원 전하량 보다 크고 주사속도 구간에서 부반응인 산소발생이 증가하고 있음을 확인했다. 그리고 Calvanostat에 의한 정전류 충방전 실험의 결과 수산화니켈 단일 입자의 방전용량은 이론용량 289 mAh/g에 근접한 수치(약 250 mAh/g)를 보여 주었으며 또한 Potential Step에 의해 단일 입자내의 수소이온 확산계수($D_{app}=3{\sim}4{\times}10^{-9}\;cm^2/s$)가 얻어졌다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제39권5호
• /
• pp.542-547
• /
• 2015

Since the oil price has been significantly jumped for several years, a heavy oil of low quality has been mainly used in the diesel engine of the merchant ship. Thus, a combustion chamber of the engine has been often exposed to severely corrosive environment more and more because temperature of the exhaust gas of the combustion chamber has been getting higher and higher with increasing of using the heavy oil of low quality. As a result, wear and corrosion of the engine parts such as exhaust valve, piston crown and cylinder head surrounded with combustion chamber are more serious compared to the other parts of the engine. Therefore, an optimum repair welding for these engine parts is very important to prolong their lifetime in a economical point of view. In this study, Inconel 625 filler metal were welded with GTAW method in the cast steel which would be generally used with piston crown material. And the corrosion properties of weld metal, heat affected and base metal zones were investigated using electrochemical methods such as measurement of corrosion potential, anodic polarization curves, cyclic voltammogram and impedance etc. in 35% $H_2SO_4$ solution. The weld metal and base metal zones exhibited the highest and lowest values of hardness respectively. Furthermore, the corrosion current density of the weld metal zone revealed the lowest value, having the highest value of hardness. The corrosive products with red color and local corrosion like as a pitting corrosion were considerably observed at the base metal zone, while these morphologies were not wholly observed in the weld metal zone. In particular, the polarization characteristics such as impedance, polarization curve and cyclic voltammogran associated with corrosion resistance property were well in good agreement with each other. Consequently, it is suggested that the mechanical and corrosion characteristics of the piston crown can be predominantly improved by repair welding method using the Inconel 625 electrode.

• 한국산학기술학회논문지
• /
• 제14권4호
• /
• pp.2037-2042
• /
• 2013

기존 DSSC의 상대전극을 TCO-less로 하여 도전성과 촉매기능을 동시에 가지고 있는 Pd의 안정성 확인을 위해 열증착기를 채용하여 유리기판 전면에 Pd를 90nm 두께로 증착하고 전해질과의 반응 안정성을 확인하였다. $0.45cm^2$급 면적을 가진 glass/FTO/blocking layer/$TiO_2$/dye/electrolyte(10 mM LiI + 1 mM $I_2$ + 0.1 M $LiClO_4$ in acetonitrile solution)/Pd/glass 구조의 DSSC 소자를 만들고, 시편제작 1시간, 12시간 후의 변화를 육안분석, 광학현미경과 FESEM을 이용하여 미세구조 분석을 진행하고, 전기적 분석은 각각 C-V(cyclic voltammetry measurements), I-V(current voltage) 분석을 통해 확인하였다. 미세구조 분석을 통하여 시간이 지남에 따라 확연히 Pd과 전해질이 반응하여 부식되는 것을 확인하였고, 전기적으로도 시간이 지남에 따라 촉매활동도와 효율이 감소하는 것을 확인하였다. 최종 효율은 1시간 후에는 0.34%의 광전효율을 보였으나 12시간 후에는 0.15%를 나타내어 약 44%로 감소하였다. 따라서 염료감응태양전지에 Pd촉매를 채용하기 위해 $I^-/I_3{^-}$ 전해질이 아닌 다른 전해질을 사용하거나 Pd 전극이 아닌 다른 촉매재를 사용해야 함을 확인하였다.

• 대한디지털의료영상학회논문지
• /
• 제11권2호
• /
• pp.115-119
• /
• 2009

I think this will be valuable reference for assuring consistency and homogeneity of clarity and managing dental radiation equipment by experimentation of dental radiation equipment permanent which based on KS C IEC 61223-3-4 standard and KS C IEC 61223-2-7. Put a dental radiation generator and experiment equipment as source and film(sensor) length within 30 em, place the step-wedge above the film(sensor). Tie up tube voltage 60 kVp, tube current 7 mA and then get an each image through CCD sensor and film by changing the exposure time as 0.12sec, 0.25sec, 0.4sec. Repeat the test 5times as a same method. Measure the concentration of each stage of film image, which gained by experiment, using photometer. And the image that gained by CCD sensor, analyze the pixel value's change by using image J, which is analyzing image program provided by NIH(National Institutes of Health). In case of film, while 0.12sec and 0.25sec show regular rising pattern of density gap as exposure time's increase, 0.4sec shows low rather than 0.12sec and 0.25sec. In case of CCD sensor density test, the result shows opposite pattern of film. This makes me think that pixels of CCD's sensor can have 0~255 value but it becomes saturation if the value is over 255. The way that getting clear reception during decreasing human's exposed radiation is one of maintaining an equipment as a best condition. So we should keeping a dental radiation equipment's condition steadily through cyclic permanent test after factor examination. Even digital equipment doesn't maintain a permanent, it can maintain a clarity by post processing of image so that hard to set it as standard of permanent test. Therefore it would be more increase the accuracy that compare a film as standard image. Thus I consider it will be an important measurement to care for dental radiation equipment and warrant homogeneity, consistency of dental image's clarity through comparing pattern which is the result from factor test against cyclic permanent test.

• Steel and Composite Structures
• /
• 제13권3호
• /
• pp.239-258
• /
• 2012

In this paper, experimental investigations on high strength steel (HSS) stud connected steel-concrete composite (SCC) girders to understand the effect of shear connector density on their flexural behaviour is presented. SCC girder specimens were designed for three different shear capacities (100%, 85%, and 70%), by varying the number of stud connectors in the shear span. Three SCC girder specimens were tested under monotonic/quasi-static loading, while three similar girder specimens were subjected to non-reversal cyclic loading under simply supported end conditions. Details of casting the specimens, experimental set-up, and method of testing, instrumentation for the measurement of deflection, interface-slip and strain are discussed. It is found that SCC girder specimen designed for full shear capacity exhibits interface slip for loads beyond 25% of the ultimate load capacity. Specimens with lesser degree of shear connection show lower values of load at initiation of slip. Very good ductility is exhibited by all the HSS stud connected SCC girder specimens. It is observed that the ultimate moment of resistance as well as ductility gets reduced for HSS stud connected SCC girder with reduction in stud shear connector density. Efficiency factor indicating the effectiveness of high strength stud connectors in resisting interface forces is estimated to be 0.8 from the analysis. Failure mode is primarily flexure with fracturing of stud connectors and characterised by flexural cracking and crushing of concrete at top in the pure bending region. Local buckling in the top flange of steel beam was also observed at the loads near to failure, which is influenced by spacing of studs and top flange thickness of rolled steel section. One of the recommendations is that the ultimate load capacity can be limited to 1.5 times the plastic moment capacity of the section such that the post peak load reduction is kept within limits. Load-deflection behaviour for monotonic tests compared well with the envelope of load-deflection curves for cyclic tests. It is concluded from the experimental investigations that use of HSS studs will reduce their numbers for given loading, which is advantageous in case of long spans. Buckling of top flange of rolled section is observed at failure stage. Provision of lips in the top flange is suggested to avoid this buckling. This is possible in case of longer spans, where normally built-up sections are used.

• 한국결정성장학회지
• /
• 제32권2호
• /
• pp.77-82
• /
• 2022

고효율의 수전해 촉매는 낮은 전압에서 빠른 속도로 산화반응이 가능하기에 반응 활성이 높은 촉매설계 및 제조 공정이 필요하다. 현재 귀금속 촉매가 산소 발생 반응 성능에 있어서 우수한 특성을 보여주고 있지만 높은 가격과 낮은 반응성에 의한 효율 한계성으로 인해 상용화에 큰 어려움을 겪고 있다. 최근 귀금속 촉매를 대체하기 위해 저비용/고효율 수전해 촉매 개발연구가 활발하게 진행되고 있는데, 본 연구에서는 가격적인 측면에서 부담이 적고 산소활성 반응이 뛰어난 니켈 금속과 전기전도성이 뛰어난 multi walled carbon nanotube(MWCNT)를 이용하고 pulsed laser ablation in Liquid(PLAL) 공정을 적용하여 MWCNT 구조내에 Ni 을 성공적으로 dopping하여 Ni-MWCNT 촉매를 제작하고자 하였다. High resolution-transmission electron microscopy(HR-TEM) 분석 및 X-ray photoelectron spectroscopy(XPS) 분석을 통하여 개발된 수전해 촉매의 구조 및 화학적 조성을 확인하였으며, 촉매 산소발생반응 평가는 선형 주사 전위법(Linear sweep voltammetry; LSV) 과전압 특성, 타펠 기울기(Tafel slope), 전기화학 임피던스 분광법(Electrochemical impedance spectroscopy; EIS), 순환 전압 전류법(Cyclic voltammetry; CV) 및 Chronoamperometry(CA) 측정법으로 진행하였다.

• 대한토목학회논문집
• /
• 제26권3C호
• /
• pp.201-207
• /
• 2006

유효응력의 산정을 위해 간극수압의 측정이 필수인 지반공학 분야의 실험에서는 멤브레인을 사용하여 구속압과 간극수압의 계측을 실시하지만 구속압의 변화 등에 의해 멤브레인이 공시체 쪽으로 관입하는 현상이 발생하여 체적변형률과 유효응력의 계측치에는 오차가 포함되게 된다. 본 연구에서는 중공비틀림 전단시험장치를 사용하여 등방제하과정과 반복전단과정 및 액상화 후의 재압밀 과정에 있어서의 멤브레인 관입량 및 관입 보정식에 대한 고찰을 실시하였다. 실험 결과, 반복전단에 의해 모래의 유효응력이 20kPa 이하의 낮은 유효응력 조건에서는 보정식에 의한 멤브레인 보정량이 과대평가 되고 있음을 알 수 있으며, 이러한 보정식의 한계는 유효응력이 0에 가까워질 수록 보정량이 급격히 증가하는 것이 원인이다. 본 연구에서는 이러한 점을 감안하여 보정량의 급증을 방지하기 위한 상수의 도입에 대해서도 검토하였다. 이와 더불어 초기 상대밀도가 높거나 액상화 후의 입자 재배열 등의 밀도 변화가 일어나는 경우에도 보정식의 적용에 대한 신중한 검토가 필요하다는 점도 확인하였다.

• Corrosion Science and Technology
• /
• 제14권2호
• /
• pp.54-58
• /
• 2015

A heavy oil of low quality has been mainly used in the diesel engine of the merchant ship as the oil price has been significantly jumped for several years. Thus, a combustion chamber of the engine has been often exposed to severely corrosive environment more and more because temperature of the exhaust gas of the combustion chamber has been getting higher and higher with increasing of using the heavy oil of low quality. As a result, wear and corrosion of the engine parts such as exhaust valve, piston crown and cylinder head surrounded with combustion chamber are more serious compared to the other parts of the engine. Therefore, an optimum repair welding for these engine parts is very important to prolong their lifetime in a economical point of view. In this study, 1.25Cr-0.5Mo filler metal was welded with SMAW method in the forged steel which would be generally used with piston crown material. And the corrosion properties of weld metal, heat affected and base metal zones were investigated using electrochemical methods such as measurement of corrosion potential, anodic polarization curves, cyclic voltammogram and impedance etc. in 35% $H_2SO_4$ solution. The weld metal and base metal zones exhibited the highest and lowest values of hardness respectively. And, the corrosion resistance of the heat affected and weld metal zones was also increased than that of the base metal zone. Furthermore, it appeared that the corrosive products with red color and local corrosion like as a pitting corrosion were more frequently observed on the surface of the base metal zone compared to the heat affected and weld metal zones. Consequently, it is suggested that the mechanical and corrosion characteristics of the piston crown can be predominantly improved by repair welding method using the 1.25Cr-0.5Mo electrode.

• 폴리머
• /
• 제36권6호
• /
• pp.756-760
• /
• 2012

본 연구에서는 콜타르 피치를 출발물질로 하여 KOH로 활성화시킨 슈퍼커패시터용 전극소재를 제작하였다. 콜타르 피치와 KOH의 활성화 비율을 1:4로 설정한 후 활성화 온도를 $600{\sim}900^{\circ}C$까지 $100^{\circ}C$ 단위로 4종류의 활성탄소를 제조한 후 피치계 활성탄소의 전기화학적 성능에 대한 KOH 활성화 온도의 영향에 관하여 고찰하였다. 또한 활성탄소의 형태학적 특성 변화를 흡착등온선과 FE-SEM을 통하여 분석하였다. 실험결과, 활성탄소의 커패시턴스는 전극 내 내부저항의 감소에 따라 증가하였는데, 이는 활성화 온도가 증가함에 따라 활성탄소 내 미세기공이 발달했기 때문이라 판단된다.

• 전기학회논문지
• /
• 제67권3호
• /
• pp.413-418
• /
• 2018

In this paper, we describe the development of a non-enzymatic glucose sensor based on copper nanocubes(Cu NCs) electroplated laser induced graphene(LIG) electrodes which can detect a certain range of glucose concentrations. $CO_2$ laser equipment was used to form LIG electrodes on the PI film. This fabrication method allows easy control of the LIG electrode size and shape. The Cu NCs were electrochemically deposited on the LIG electrodes to improve electron transfer rates and thus enhancing electrocatalytic reaction with glucose. The average sheet resistances before and after electroplating were $15.6{\Omega}/{\Box}$ and $19.6{\Omega}/{\Box}$, respectively, which confirmed that copper nanocubes were formed on the laser induced graphene electrodes. The prepared electrode was used to measure the current according to glucose concentration using an electrochemical method. The LIG electrodes with Cu NCs demonstrated a high degree of sensitivity ($1643.31{\mu}A/mM{\cdot}cm^2$), good stability with a linear response to glucose ranging from 0.05 mM to 1 mM concentration, and a limit of detection of 0.05 mM. In order to verify that these electrodes can be used as flexible devices, the electrodes were bent to $30^{\circ}$, $90^{\circ}$, and $180^{\circ}$ and cyclic voltammetry measurements were taken while the electrodes were bent. The measured data showed that the peak voltage was almost constant at 0.42 V and the signal was stable even in the flexed condition. Therefore, it is concluded that these electrodes can be used in flexible sensors for detecting glucose in the physiological sample like saliva, tear or sweat.