• Journal of Korean Society of Steel Construction
• /
• v.28 no.6
• /
• pp.467-476
• /
• 2016

For the connections between modular units in modular buildings, the bolted joints with connector plates are used commonly. The strength of structure is determined by the weakest part of structure and the connections may be weaker than the members being joined. Therefore, to check the safety of modular building, the structural performance of connections between modular units as well as that of beam-to-column connections should be evaluated. In this study, the behavior of module to module connection with straight and cross shaped connector plates is investigated by lateral cyclic tests according to KBC2009 0722.2.4 which shall be conducted by controlling the story drift angle in the width and the longitudinal direction respectively. All of test results generally show the stable ductile behavior up to 0.04rad drift levels and the tests in longitudinal direction show a superior energy dissipation per cycle in each of the load steps. However, the straight shaped connector plates have the degradation of stiffness with cyclic loading and the larger drift angle of column than the cross shaped connector plates.

• Applied Chemistry for Engineering
• /
• v.8 no.4
• /
• pp.568-574
• /
• 1997

The effect of microencapsulation of maetal hydride (MH) with copper on the electrode performance of a Ni/MH battery has been investigated. The MH electrodes were prepared with a combination of cold press and paste methods. The discharge capacity of the electrode increased with an addition of small amounts if CMC into the electrode, but decreased when heat-treated in an oxygen-free nitrogen flow. The capacity of a Cu-coated $LaNi_5$ electrode was higher than that of LaNi5electrode. The discharge capacity of the electrode prepared with Cu-coated $LaNi_5$ increased with the increase of copper content in the electrode. It is considered that the increase of copper content enhanced the current density on the electrode surface, leading to the increase of the discharge capacity The MH electrode coated by an acidic electroless plating method showed much higher discharge capacity than that using an alkaline electroless plating method. The discharge capacity of the $LaNi_{4.5}Al_{0.5}$ electrode was higher than that of the $LaNi_5$ electrode. Also, the effect of microencapsulation on the deactivation of $LaNi_5$ was studied using an absorption-desorption cycle in CO-containing hydrogen.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.5 no.2
• /
• pp.75-91
• /
• 2003

This study analyzed descriptions about dots, lines, and sides which are used as a basic elements to express geometric figures as followings: -In the aspect of formative art, dots form images and feelings through their concurrence when make a slight move to coordinates. The concurrence can bring out either positive or negative images; -Lines have unlimited variation as a core measure in body art. They can make optimal effects with different lines such as straight and curved lines of human body; -Sides express not only effects of texture and perspective but also of space and solid by color effects. Expressive characteristics and geometric shapes can be classified by tattoo, henna and body painting: First, colorful tattoos are favored by Caucasian and original tattoos are mostly used by yellow and colored races in the way of scarification to get decorative effects. Recently, a rapid cycle of fashion change in tattoo figures has developed a tentative method of tattooing and a variety of decoration methods. It has made it a lot easier to change a pattern of a tattoo. Tattoos are now popular among people because they no longer have to suffer from pains when they get their body tattooed for a long time. Since tattoos boast their unique beauty which consists of most dynamic and attractive images among the types of body art. It will be one of the most favored make-up methods in the nearest future. Second, geometric designs used in henna include crosses, dots, straight lines, triangles, date palms, and so on. Henna has been particularly loved as an instant decoration by the public since it gradually disappears as time goes on. Third, body painting enables to draw a three-dimensional effect because of its close relation with body movements in a limited space. Each individual will have a different feeling appealed in their body painting. Body painting has been applied to many different areas, especially to theatrical art using lights, music and performance altogether producing impromptu and experimental works. Unlike other arts such as painting, sculpture, visual and industrial arts, body painting has mobility. Since it is painted on a three-dimensional human body, it can bear originality expressing realistic objects or animals and strengthen creative functions using body lines. Moreover, geometric designs can be diversified by the sexes. As a result of analysis, geometric designs expressed in body art seemed to transcend expressions of beauty and turned out to be another way of decoration. Body art has also been used as a way to express visual integration and consolidation dynamically not by human instinct but by social changes. The needs for body art will grow as the future comes nearer and be recognized as a new and fresh value. Formative elements of geometric figures deliver visual impressions combined with human body and finally create more various types of body art in harmony of body lines.

• Korean Chemical Engineering Research
• /
• v.46 no.2
• /
• pp.414-422
• /
• 2008

Adsorption experiments for $H_2$, $CH_4$, CO, $CO_2$ on activated carbon and zeolite 5A were performed by static volumetric method. A 4-bed pressure swing adsorption (PSA) process was to study separation of hydrogen from multi-component mixture gases ($H_2$ 72.2%, $CH_4$ 4.06%, CO 2.03%, $CO_2$ 21.6%). Dual-site langmuir (DSL) isotherm showed good or fair agreement with the experimental results. The optimum height of activated carbon layer was 55 cm with breakthrough results on the packing ratio of activated carbon to zeolite 5A. In PSA process, the effects of the process parameters such as total cycle time ($T_c$), ${\Delta}P$ at the provide purge step and adsorption pressure on the PSA performance were studied experimentally and theoretically.

• Journal of the Korean Electrochemical Society
• /
• v.11 no.4
• /
• pp.289-296
• /
• 2008

Electrochemical studies were performed by a half-cell test for the nickel hydroxide (cathode) and hydrogen storage alloy(anode) electrodes for the sealed Ni-MH batteries applicable to industrial use. The electrodes were fabricated and checked a charge efficiency and an internal pressure of the battery during charge-discharge cycling. In order to reduce the internal pressure of the sealed Ni-MH battery, cyclic voltammetry (CV) were performed on the electrodes of nickel hydroxide(cathode) and hydrogen storage alloy(anode), respectively. The results of the test showed clearly the oxidation/reduction and oxygen evolution reaction in a nickel hydroxide electrode and the hydrogenation behavior of a hydrogen storage electrode. The sealed Ni-MH battery of 130Ah was fabricated by using nickel hydroxide of a high over-voltage for an oxygen gas evolution and hydrogen storage alloy of a good performance for activation The battery showed a good characteristics such as a high charge efficiency of 98% at 1 C charge current, a low level internal pressure of 4 atm on a continuous over-charging and a large preservation capacity of 95% at 400 cycle.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.7
• /
• pp.741-753
• /
• 2008

This paper explores the throughput performance of CSMA/CA-based DCF protocol over both ideal channels and fading channels with payload size at the MAC layer in the 802.11a wireless LAN. In the ideal channel, there are no errors and at the transmission cycle there is one and only one active station which always has a packet to send and other stations can only accept packets and provide acknowledgements. In the fading channel, bit errors appear in the channel randomly and the number of stations is assumed to be fixed. And each station always has packets for transmission. In other words, we operate in saturation conditions. Up to now conventional research work about DCF throughput analysis of IEEE 802.11 a wireless LAN has been done over the ideal channel, but this paper is done over the Rayleigh/Ricean fading channel. So, the ratio of received average energy per bit-to-noise power spectral density $E_b/N_o$ is set to 25 dB and the ratio of direct-to-diffuse signal power in each sub-channel $\xi$ is set to 6 for combined Rayleigh/Ricean fading channel. In conclusion, it is shown that the saturation throughput is always less than the maximum throughput at all the payload size and the higher the transmission rate be, the higher the decreasing rate of saturation throughput compared to the maximum throughput be.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.45 no.9
• /
• pp.784-793
• /
• 2017

A two-axis gimbal-type X-band antenna mounted on an observation satellite can efficiently transmit high-capacity image data to a ground station regardless of both the satellite position and the orbital motion. However, this X-band antenna induces unnecessary micro-jitter which can degrade the image quality of the high-resolution observation satellite. Therefore, to achieve the high-resolution image quality from the observation satellite, micro-jitters have been required to be isolated. In this study, to resolve aforementioned drawback, we proposed blade gear using a shape memory alloy (SMA) applied to azimuth stage of X-band antenna. To investigate the rotational basic characteristics of the proposed SMA blade gear, we performed rotational static loading test. Futhermore, to evaluate the cycle to failure of the gear, accelerated life test was conducted. The temperature test was conducted to confirm rotational basic characteristics at various temperature conditions. To verify the isolation performance for micro-jitter, we performed micro-jitter measurement test.

• Journal of Animal Environmental Science
• /
• v.9 no.2
• /
• pp.69-78
• /
• 2003

In this study, the energy conversion equipment from the radiation energy to mechanical energy by using n­pentane as the operating fluid was constructed and the performance to pump the water was tested for the utilization of solar powered water pump. The equipment was designed optimally, after the theoretical analyses of the water pumping head and water quantity per cycle were done. The pentane vapour temperature in the condenser and the temperature of the outlet water from the condenser became lowered and the heat transfer rate became higher with decreasing the water inlet level to the condenser. The temperature difference between the condenser and the water tank was significant. Therefore, the distance between the water tank and condenser was recommended to be shorten and the diameter of their connecting pipe was recommended to be narrow in order to reduce the resistance of the fluid passage and improve the heat transfer rate. The amount of water pumped was 1.6­2.4 liters. Mass flow rate of the cooling water became lowered when the cooling water pipe was prolonged from the condenser to improve the heat transfer rate.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.12
• /
• pp.4205-4209
• /
• 2011

The $Li_2Mn_{0.5}Fe_{0.5}SiO_4$ silicate was prepared by blending of $Li_2MnSiO_4$ and $Li_2FeSiO_4$ precursors with same molar ratio. The one of the silicates of $Li_2FeSiO_4$ is known as high capacitive up to ~330 mAh/g due to 2 mole electron exchange, and the other of $Li_2FeSiO_4$ has identical structure with $Li_2MnSiO_4$ and shows stable cycle with less capacity of ~170 mAh/g. The major drawback of silicate family is low electronic conductivity (3 orders of magnitude lower than $LiFePO_4$). To overcome this disadvantage, carbon composite of the silicate compound was prepared by sucrose mixing with silicate precursors and heat-treated in reducing atmosphere. The crystal structure and physical morphology of $Li_2Mn_{0.5}Fe_{0.5}SiO_4$ was investigated by X-ray diffraction, scanning electron microscopy, and high resolution transmission electron microscopy. The $Li_2Mn_{0.5}Fe_{0.5}SiO_4$/C nanocomposite has a maximum discharge capacity of 200 mAh/g, and 63% of its discharge capacity is retained after the tenth cycles. We have realized that more than 1 mole of electrons are exchanged in $Li_2Mn_{0.5}Fe_{0.5}SiO_4$. We have observed that $Li_2Mn_{0.5}Fe_{0.5}SiO_4$ is unstable structure upon first delithiation with structural collapse. High temperature cell performance result shows high capacity of discharge capacity (244 mAh/g) but it had poor capacity retention (50%) due to the accelerated structural degradation and related reaction.

• Korean Journal of Optics and Photonics
• /
• v.5 no.3
• /
• pp.423-430
• /
• 1994

We designed and fabricated the single mode fiber pigtailed DFB-LD module for 2.5 Gbps optical communication system. In the design of the DFB-LD module, we made the module divided into two parts of inner sub-module and outer 14-pin butterfly package and cylindrical shaped sub-module contain quasi confocal 2 lens system including optical isolator and electrical connection between these parts via hybrid substrate of bias T circuit. Laser welding was used to assemble the sub-module which requires accurate fixing between optical elements. The fabricated DFB-LD module showed optical coupling efficiency of 20% and - 3 dB small signal response of more than 2.6 GHz. We confirmed mechanical reliability of the module by temperature cycle test where the tested module exhibit optical power fluctuation of less than 10%. Finally we evaluated the performance of the fabricated DFB-LD module as light source of 2.5 Gbps optical communication system, sensitivity of - 30.2 dBm was obtained through 47 km optical fiber transmission under the criterion of $1\times10^{-10}$ BER and transmission penalties were 1.5 dB caused by extinction ratio and 1.0 dB caused by chromatic dispersion of normal single mode fiber. fiber.