• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2017.05a
• /
• pp.252-254
• /
• 2017

Tire is one of the most important to drive cars. There is high possibility to occur slip phenomenon and to increase braking distance depending on tire wear. Therefore, you should be check tire wear and replace tires periodically. In the past, most people manually check the wear level and judged whether or not to replace the tire. But, since the standard is different for each person, the replacement cycle becomes unclear. Since a clear replacement cycle is established, it is expected that the accident rate of a vehicle caused by a tire will be reduced. Therefore, i propose detection method for a tire wear using a motor rotation angle.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.03a
• /
• pp.871-876
• /
• 2008

The blade vibration problem of bladed disk is the most critical subject to consider since it directly affects the stable performance of the engine as well as life of the engine. Especially, due to complicated vibration pattern of the bladed disk, more effort was required for vibration analysis and test. The research of measuring the vibration of the bladed disk, using NSMS(Non-intrusive stress measurement) instead of Aeromechanics testing method requiring slip ring or telemetry system with strain gauge, was successful. These testing can report the actual stresses seen on the blades; detect synchronous resonances that are the source of high cycle fatigue(HCF) in blades; measure individual blade mis-tuning and coupled resonances in bladed disks. In order to minimize the error being created due to heat expansion, the tip timing sensor is installed parallel to the blade trailing edge, yielding optimal result. Also, when working on finite element analysis, the whole bladed disk has gone through three-dimensional analysis, evaluating the family mode. The result of the analysis matched well with the test result.

• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 2004.04a
• /
• pp.139-144
• /
• 2004

This study aims to analyze the accuracy of rover speed change in route surveying using RTK-GPS. Route surveying methods using GPS contain Static, DGPS, and RTK-GPS. Much research of navigation system, positioning of vehicles by DGPS, and accuracy analysis by GPS surveying have already been done. From this study, it is firstly found that DGPS is suitable for car navigation and sea navigation with an error of meter scale but not good for detailed construction, designing maps and updating GIS databases. Secondly, RTK-GPS can be used for managing gas pipes, water supply and drain pipes and fiber-optic cable that are needed to be controlled in a real time basis. Thirdly, since the accuracies of route surveying by RTK-GPS and DGPS are not correctly matched with the change of rover speed, the choice of route surveying method from those two should follow the need of accuracy fidelity Further study should focus on Cycle Slip problem and coordinate change problem in tunnel and mountainous areas.

• Journal of the Korean Society for Heat Treatment
• /
• v.4 no.4
• /
• pp.24-33
• /
• 1991

The effects of thermomechanical treatments on microstructure and fatigue properties of 7050 Al alloy were investigated. The precipitation kinetics changed to a faster rate due to cold deformation employed in this special TAHA thermomechanical treatments including pre-aging, plastic deformation and two step final-aging. The G.P. zones in the under-aged condition were cut by dislocations and dissolved during the plastic deformation. During the low cycle fatigue, the T6' condition showed cyclic hardening behavior whereas the TMT5, TMT27 and T76 conditions showed cyclic softening at above 0.7% total strain amplitudes. The ${\Delta}K_{th}$ value of TMT27 was improved more than two times, compared with that of T76 condition. The T6' with small shearable precipitates resulted in the markedly high ${\Delta}K_{th}$ value. This is thought to be resulted from dislocation reversibility and roughness-induced crack closure due to planarity of slip.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.12
• /
• pp.61-67
• /
• 2005

This paper presents the carrier phase DGPS method providing a stable navigation solution under the condition of frequent blockage of the GPS signals. The proposed algorithm reject the channels having large errors using a clock bias drift and then calculated the more accurate solution. By investigating the relation between visible satellites` elevation and their clock bias drift, a proper threshold is set. Simulation shows that the presented result is as good as that of commercial system with real data.

• Journal of Institute of Control, Robotics and Systems
• /
• v.18 no.11
• /
• pp.1034-1039
• /
• 2012

In this paper, a structure of precise positioning based on satellite navigation system is proposed. The proposed system is consisted with three parts, range domain filter, navigation filter and position domain filter. The range domain filter generates carrier phase-smoothed-Doppler and Doppler-smoothed-code measurements. And the navigation filter calculates position and velocity using double-differenced code/carrier phase/Doppler measurements. Finally, position domain filter smooth position error, and it means enhancement of positioning performance. The proposed positioning method is evaluated by trajectory analysis using precise map date. As a result, the position error occurred by multipath or cycle slip was reduced and the calculated trajectory was in true lane.

• 유체기계공업학회:학술대회논문집
• /
• 2001.11a
• /
• pp.482-487
• /
• 2001

Leaf type foil bearings have been used successfully in many aerospace applications such as air cycle machines, turbocompressors and turboexpander. These applications are characterized by light loads, constant speeds and low to moderate temperatures. But, as system on start-up or shutdown, sliding contact between the shaft and foil surfaces cause wear. So, in present study, to understand pressure-flow characteristics and deformation of foil bearing, flow/structure interaction analysis was used. and using this method, 2D and 3D calculation was peformed for shape of foil bearing to know circumferential direction flow and leakage flow characteristics of axial direction.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11a
• /
• pp.331.1-331
• /
• 2002

Four degrees of freedom mathematical model is presented to describe the fundamental mechanisms of the disc brake squeal noise. A contact parameter is introduced to describe the coupling between the in-plane and the out-of-plane motions. The friction coeficient including "relative velocity" and ′normal force" can be generally formulated as the form of multiplication with polynominal parameters(${\beta}$, ${\gamma}$). (omitted)

• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.1
• /
• pp.31-36
• /
• 2009

This paper presents a novel scalar adaptive filter, which is reformulated by additional acceleration term. The filter continuously estimates three different kinds of covariance such as the measurement noise covariance, the velocity error covariance and the acceleration error covariance. For estimating three covariances, we use the innovation method for the measurement noise covariance and the least square method for other covariances. In order to verify the proposed filter performance compared with the conventional scalar adaptive filter, we make indoor experimental environment similar to outdoor test using the ultrasonic sensors instead of GPS. Experimental results show that the proposed filter has better position accuracy than the traditional scalar adaptive filter.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.6 no.1
• /
• pp.49-58
• /
• 2003

Compared with generic GPS receiver, post-processing software GPS receiver has many advantages for high dynamic vehicle tracking. It has the advantage of the application of various tracking algorithms and aiding schemes. The post-processing system observes the carrier phase measurement data from the recorded GPS signals, detects and isolates the cycle slip. The observed carrier phase data and the raw data of the reference station are processed by carrier phase DGPS scheme. And the integer ambiguity resolution algorithm is used for resolving single frequency carrier phase ambiguity. The results of static and real flight test are presented and show that the proposed GPS translator processing system satisfies submeter accuracy.