• 대한전자공학회논문지SD
• /
• 제48권7호
• /
• pp.76-81
• /
• 2011

본 논문에서는 비아 절단 구조를 제안하고 2층 구조의 DRAM 패키지 기판 설계에 적용하여 낮은 임피던스를 가지는 파워 분배망(Power Distribution Network)을 구현하였다. 제안한 신규 비아 구조는 비아의 일부가 절단된 형태이고 본딩 패드와 결합하여 넓은 배선 면적을 필요로 하지 않는 장점을 가진다. 또한 비아 절단 구조를 적용한 설계에서는 본딩 패드에서 VSSQ까지의 배선 경로를 효과적으로 단축시킴으로써 PDN 임피던스를 개선시킬 수 있다. DRAM 패키지 기판 상의 윈도우 영역 형성과 동시에 비아의 일부 영역이 제거되므로 비아 절단 구조 제작을 위한 추가적인 공정은 없다. 또한 비아 홀 내부를 솔더 레지스트로 채움으로써 버(Burr) 발생을 최소화하였으며, 이를 패키지 기판 단면 촬영을 통해 검증하였다. 비아 절단 구조의 적용 및 VDDQ/VSSQ 배치에 의한 PDN 임피던스 변화를 검증하기 위해서 3차원 전자장 시뮬레이션 및 네트워크 분석기 측정을 통해 기존 방식을 적용한 패키지 기판과 비교 검증을 진행하였다. 신규 DRAM 패키지 기판은 대부분의 주파수 범위에서 보다 우수한 PDN 임피던스를 가졌으며, 이는 제안한 비아 절단 구조와 파워/그라운드 설계 배치가 PDN 임피던스 감소에 효과적임을 증명한다.

• 한국정밀공학회지
• /
• 제17권5호
• /
• pp.116-123
• /
• 2000

This paper presents an NC code post-processor that adjusts feedrates to keep the variation of metal removal rate along the tool paths minimum. Metal removal rate is estimated by virtually machining the part, whose surface model is built from a series of NC codes defined in operation plan, with cutting-tool-assembly models, whose geometry are defined in a machining database. The NC code post-processor modifies the feedrates by the adjustment rules, which are based on the machining knowledge for effective machining. This paper illustrates a procedure fur grouping machining conditions and we also show how to determine an adjustment rule for a machining-condition group. An example part was machined and it shows that the variation of cutting force was dramatically reduced after applying the NC code post-processor. The NC code post-processor is expected to increase productivity while maintaining the quality of the machined part.

• 한국세라믹학회지
• /
• 제40권10호
• /
• pp.931-935
• /
• 2003

A complex-shaped part was successfully fabricated by Laminate Object Manufacturing (LOM) technique using silicon nitride tape with aligned silicon nitride whisker seeds. The ceramic tape was cut using a commercial cutting plotter according to the cross section drafts generated by slicing a 3-D model, and then the tapes were stacked sequentially. In order to improve adhesion between the tapes, stacking was performed under vacuum. After binder burnout, the part was encapsulated using latex emulsion and was cold isostaically pressed under 250 ㎫. It was sintered to 98.5% TD at 2148 K for 4 h under 2 ㎫ nitrogen pressure.

• 한국정밀공학회지
• /
• 제18권8호
• /
• pp.96-106
• /
• 2001

As the drilling depth increases, the cutting torque increases and fluctuates, which can lead to the machine tool vibration, severe tool wear, and catastrophic tool breakage. Hence, cutting torque control is very important to improve productivity in drilling. In this paper, a PID controller was designed to control the drilling torque. The plant including the feed drive system, cutting process and spindle drive system was modeled for controller design. The Ziegler-Nichols method was used to determine the controller gain and control action times and the root locus plot was used to tune the controller gain for a certain cutting condition. Also, suggested was a simple method to obtain the tuned controller gain for an arbitrary cutting condition not using the Ziegler-Nichols method and the root locus plot. The performance of the designed controller and the effect of controller gain tuning were verified from experiments.

• Journal of Ecology and Environment
• /
• 제35권3호
• /
• pp.235-242
• /
• 2012

Mikania micrantha, a neo-tropical vine, is spreading rapidly in the tropical part of Nepal and is now threatening the rural ecosystem including biodiversity and rural livelihoods. However, no attempt has been made to control the spread of M. micrantha. As a result, the vines are spreading freely and rapidly. After a thorough literature review and assessment of forest management practices, we proposed a manual cutting method, as it suits the Nepalese situation for several reasons: required labor is readily available, as local communities are managing forest patches, and the method does not have any potential adverse effects on non-target native species. Experimental plots were laid out in August 2011 to examine the effectiveness of manual cutting. Two different site types based on canopy coverage were selected and divided into three blocks based on cutting strategy. Four treatments were assigned across the experimental plots following a complete block design. We harvested above-ground biomass according to the assigned treatment. The results suggested that there should be at least two consecutive cuttings within a 3-week interval before flowering, and that three consecutive cuttings resulted in 91% mortality of the vines. In addition, cutting promoted regeneration of native plant species. Employing regular cutting operations can modify understory shade enhancing regeneration of native species, which is a desirable condition to constrain proliferation of M. micrantha. Periodic cuttings reduced the competitiveness of M. micrantha regardless of canopy openness, but native ground cover should be retained.

• 한국초지조사료학회지
• /
• 제1권1호
• /
• pp.10-17
• /
• 1978

The experiment were carried out to determine the rate of regrowth, the changes of carbohydrates contained in the samples right after cutting, plant part for storage of carbohydtates and top-dressing time of ladino clover and orchardgrass. Plants were grown in the simple growth chamber as well as in the fields. The temperature, light intensity and light period were controlled to be 15-20$^{\circ}$, 4,250 Lux, and 15 hours in the simple growth chamber. The results obtained are as follows ; 1. The period of recovery to initial stands after cutting was about 3 weeks in ladino clover and 4-5 weeks in orchard grass in terms of dry matter and carbohydrates. 2. The content of total water-soluble carbohydrates of plant parts was the hightest in stolon of ladino clover and in sheath of orchardgrass, and the lowest in roots of ladino clover and orchardgrass. 3. Cutting resulted in a temporary decrease of total water-soluble carbohydrates in the shoots. Similar trends were observed when the plants were left intact with top-dressing. 4. The top-dressing applied simultalliousely with the cutting was more effective to stimu1ate regrowth than that applied after cutting, however, both of the simultaneous and after cutting application were still better than application prior to cutting.

• 한국지반환경공학회 논문집
• /
• 제6권2호
• /
• pp.15-20
• /
• 2005

도로 주변 절토사면 상부에 시공되는 산마루 측구는 상부로부터 흘러내리는 지표수를 원활히 배수시켜 절개면으로 유입되는 것을 방지한다. 국내의 경우 전 국토의 70%이상이 산악지로 구성되어 있어 도로 개설에 따른 절개면의 발생은 필연적이다. 여름 집중호우와 간극수압의 증가로 인하여 절개면의 불안정성은 증가된다. 그러나 절토사면 상부에 시공되어 있는 산마루측구는 품질관리의 어려움과 배수능력 부족 등의 문제점들이 있다. 따라서, 본 논문에서는 산마루 측구의 깊이와 투수계수에 따른 절토사면의 안전율 변화를 분석하였으며 적절한 측구 설치깊이를 결정하였다.

• 한국환경복원기술학회지
• /
• 제15권1호
• /
• pp.53-62
• /
• 2012

Culm cutting is very effective and convenient method for asexual propagation and even much less destructive than the other ways such as excavation of rhizomes. Despite that culm cutting is such a useful method, only few investigations for raising its efficiency have been carried out. We tried to examine the effect of different geographical populations and cutting sections on the shoot emergence, biomass production and its allocation in terms of cutting efficiency. Culms were sampled from three environmentally distinct wetlands : riparian marsh, salt marsh and montane fen and then they were cut separately into four sections from the bottom to the top part. Both factors of different population and section affected the shoot emergence together. Middle parts on the culm always showed more shoot emergence irrespective of different population. On the other hand, first section from salt marsh and fourth section from the montane fen did not exhibit any shoot emergence. Significant difference in increase of shoot emergence between different sections during investigation period was confirmed only from salt marsh population. Not only different population but also appropriate cutting section should be considered together for better efficiency in cutting of reed culms.

• 한국정밀공학회지
• /
• 제13권12호
• /
• pp.30-37
• /
• 1996

On-line process control equipment for CO$_{2}$ laser cutting is not available for industrial applications. The major part of the industrial laser cutting machines are adjusted off-line by highly educated engineers. The quality inspection of the sample is visual and referred to different quality scales. Due to the lack of automation the potential laser users hesitate to implement the cutting method. The first step toward an automation of the process is the development of a process monitoring system and the research is cincentrated on the area of on-line quality monitoring during CO$_{2}$ laser cutting. The method is based on the detection of the emitted light from the cutting front by photo diode. The developed monitoring system consists of the OP Amplifier, A/D convertor, power supply and PC. The signal from the photo diode has been undertaken from Fourier analysis and statistical analysis with real time. The photograph of striation pattern was taken by metallurgical microscope. As a result, it is possible to predict the striation pattern according to the beam traveling speed.

• 한국물환경학회지
• /
• 제23권3호
• /
• pp.348-355
• /
• 2007

We investigated temporal changes of composition, habitat area, growth rate and elements content of hydrophytes at the artificial vegetation island (AVI) in Kyungan Stream within Lake Paldang. We also assessed nutrient removal rate through cutting off the emergent part of hydrophytes. The kinds of hydrophytes have increased from four species (P. australis, P. japonica, T. angustifolia and the Z. latifolia) at initial stage of installation to more than 29 species for 6-year operation. P. japonica was most dominant species at the AVI in 2006. The habitat area of have increased about 2.5 times compared to the initial planting area, occupying 63% of AVI's vegetation area. The incoming species of S. fluviatilis and B. frondosa have adapted successively and expanded habitat area in the AVI. The relative growth rate of P. japonica and P. australis was highest in spring sprouting period. Their hights and weights have increased until summer, by the time they were cutting off the emergent part. They started regrowth immediately after cutting and continued to grow until September and withered away in November. The carbon contents of P. japonica and P. australis have increased during growth phase, on the contrary, the nitrogen and phosphorus contents have decreased. By cutting off and removing the emergent part (leaves and branches) of hydrophytes twice from AVI, $17.6gN/m^2/y$ of nitrogen and $1.3gP/m^2/y$ of phosphorus was removed from AVI in 2006.