• Journal of the Korean Geographical Society
• /
• v.42 no.3 s.120
• /
• pp.388-404
• /
• 2007

This study interprets evolution of fluvial terraces along the four Yeongdong- and Yeongseo streams such as Naerin River, Yeongok River, Golji River and Osip River, in Gangwon Province based on the tectonics. The results from the analyses of the distribution pattern of fluvial terraces and incision rates of rivers show distinctively the evidence as the axis of uplift by Taebaek Mountains, especially on the 4th, 5th and 6th terraces in upper reach of Osip River among the four streams. The axis of uplift extends to the zone of $30\sim40km$ in width as well as the divide. The difference of uplift between upper and middle reaches of Naerin River and total reach of Golji River wasn't found from the height from riverbed by the active uplifting along all reaches, estimated to be set in inner area of uplift zone. Incision rate of period between formation age of 2nd terrace and 1st terrace is calculated $0.13\sim0.22m/ka$, and incision rate of period between formation age of 1st terrace and Present is diversely calculated $0.17\sim0.27m/ka$ by the climatic discrepancy between the two periods. The incision rate of Yeongdong streams whose mouths reach to the sea level eroded actively more than Yeongseo streams in the uplift zone. And Yeongdong streams between formation age of 1th terrace and present appears to much higher than that of Yeongseo streams, due to active down-cutting in oder to balance against the sea level.

• The Journal of the Korea Contents Association
• /
• v.13 no.7
• /
• pp.131-140
• /
• 2013

Power shoulder look is most noticeable trend in women's wear in the 09/10 season. Specially jackets with sharper angle and wider shoulder became the best item since then, and were chosen for must-have item by fashion directors. Jacket occupied 50% in power shoulder items. Its shoulder angle was from 0 to 30 degree but items with 15 degree stood out among them. There are three methods to make power shoulder look jackets; shoulder extension method with moving shoulder tip up and sleeve cap height, method of extension and cutting sleeve cap with shorten shoulder length, and method of extension and moving shoulder tip up in the sleeve with shoulder line like raglan sleeve. As a result, shoulder angle is higher, starting point of shoulder line is closer to side neck point and shoulder point is extender to outside for appearance and fit. In shoulder extension method, the arm hole line was drawn with care by matching joining shoulder seam and setting the sleeve into the arm hole. In sleeve cap transformation, it is desired that starting point shoulder angle is moved closely to side neck point. In case of the sleeve with shoulder line, it needs to consider enough ease of shoulder and upper arm. For making patterns of power shoulder look jacket, it need to consider arm hole line, shoulder length, shoulder point position, sleeve cap height and sleeve width with interpretation design facts. In this study, through the analysis clothing construction method of power shoulder jacket, it is of help to pattern making for various power shoulder design items.

• Journal of Korean Society of Forest Science
• /
• v.89 no.3
• /
• pp.414-421
• /
• 2000

This study was carried out for the artificial forest stand of 23 years old jack pine(Pinus banksiana Lamb.) in Soheul-myun, Pochun-kun, Kyunggi province of Korea. The objectives of this study were to investigate the stand volume increment and the rate of stand volume, and were to investigate present stand volume to determine annual cutting volume for keeping stand volume to an ideal level for investigated jack pine stand. For a reasonable calculation of stand volume increment, diameter of breast height(DBH), tree height, bark width, and core length for the last 10 years for respective sampling plots were measured. By using these measurements annual diameter increment in DBH class, stand volume increment of 95% confidence interval and tree height curve equation were calculated. The tree height value was derived from the tree height curve equation. Calculation of tree volume by using the tree volume table was made by conferring the tree height value. The summarized results for investigated jack pine trees were having 7.7% annual stand volume increment with 6.1% estimated error. The total stand volume per ha was $79.58m^3$, accordingly the annual stand volume increment was $6.13m^3$ per ha, and the 95% confidence intervals range from 5.77 to $6.51m^3$.

• Journal of Periodontal and Implant Science
• /
• v.37 no.4
• /
• pp.791-803
• /
• 2007

The purpose of this study was to evaluate exophytically vertical bone formation in residual ridge of the beagle dog by the concept of guided bone regeneration with a titanium reinforced e-PTFE membrane combined with irradiated cancellous human bone. Twelve male beagle dogs(mean age 1.5 years and mean weight 12kg) were used for this study. The alveolar ridges after extraction of all mandibular premolars were surgically and horizontally removed. At 8 weeks after extractions, full-thickness flap was reflected and cortical bone was removed with round bur and copious irrigation. Rectangular parallelepiped(10mm in length, 5mm in width, and 4mm in height) bended with titanium-reinforced e-PTFE(TR e-PTFE) membrane was placed on the decorticated alveolar ridge, fixed with metal pins and covered with full-thickness flap and assigned as a control group. Test groups ere treated with TR e-PTFE membrane filled with irradiated cancellous human bone. Of twelve beagle dogs, four control dogs and four test dogs without membrane exposure to oral cavity were sacrificed at 8 and 16 weeks respectively. The surgical sites were dissected out, fixed in 4% buffered formaldehyde, dyed using a Villanueva staining technique, and processed for embedding in plastic resin. The cutting and grinding methods were routinely processed for histologic and histomophometric analyis of exophytic bone formation as well as statistical analysis. The results of this study were as follows: 1. Exophytic bone formation in the both of experimental groups was increased respectively after surgery from 23.40% at 8 weeks to 46.26% at 16 weeks in the control groups, from 40.23% at 8 weeks to 47.11% at 16 weeks in the test groups(p<0.05). 2. At 8 weeks after surgery, exophytic bone formation was made 40.23% in the test groups and 33.40% in the control groups. Exophytic bone formation was significantly made in the test group more than in the control group. At 16 weeks after surgery, exophytic bone formation was made 44.11% in the test groups and 46.26% in the control groups. Exophytic bone formation was made in the test groups more than in the control groups, but there was no statistically significant differences. 3. The membrane was fixed with metal pins to closely contact it to the bone surface. So, collapse and deviation of the membrane could be prevented and in growth of connective tissue also could be blocked from the periphery of the membrane. On the basis of these findings, wee suggest that intraoral experimental model for exophytic bone formation may be effective to evaluate the effect of bone graft material. And it indicates that combined use of membrane and ICB graft material is more effective than use of membrane only for exophytic bone formation.

• Journal of Sericultural and Entomological Science
• /
• v.47 no.2
• /
• pp.68-77
• /
• 2005

A characteristic of subtropical zones region MK-T2 compares with an gaeryangppong, and the 9-10 schedule the times when a leaf blooms to are fast, and ratio that a branch edge by the colds becomes lean showed 5.7%, and a growth of the new branch which went out delivers 67.2 cm, mulberry loaves of the new branch which went out, and 18.6, a form of a leaf is the 1.10 that length of a leaf grew more a bit than width of a leaf up. Thickness of a leaf is $228.2{\mu}m$, and an area is more similar than gaeryangppong as $225.6cm^2$. in plant taxonomy, the hair whom the style exists short with 0.7 mm, and go to the pistil head inside so as to be rare is distributed, and belong to Dolichostylae Pubescentes. The new branch cutting which executed without remedy processes was independent of a thickness of a case branch, and the form and 100% root was said, and an gaeryangppong compared with the fact that 10% root went out of 15 mm ideal, and was excellent very, and looked, a root went out a root the soil and water, all showed a characteristic to go out at central of a branch bases at 45% ratio. Length was 24.6 mm, and were water rate 78.8%, and mulberry of MK-T2 was carrying together sweetness and acidity to pH 4.7 while, besides, arrival was 19.21 Brix%. A larva period and pupa ratio, cocoon thickness ratio are almost similar to gaeryangppong, or weight of one cocoon, cocoon thickness, 20,002 cocoon quantity shows some results to drop, and be soft of a leaf, and feed value certifications are comparatively top-ranking. As a result of having analyzed amino acid of the 3rd day of 5th silkworm larva which bred to MK-T2, a collation absorbing an gaeryangppong went, and looked, but compared with a collation in case of tests to eat MK-T2, and looked, and the lie collations were not detected a difference at Leu, but MK-T2 tests were detected mutual almost similar amino acid creation. medical efficacy of the 3rd day of 5th silkworm larva ethanol extract which bred to MK-T2 and black results, histologic a case did not appear at HE dyeing about the kidney organization which extracted form the rats which ate a silkworm ethanol extract and dyeing all chemical organization immunity, and one step protein revelation became lower with almost unidentified levels.

• Journal of Korean Society of Forest Science
• /
• v.16 no.1
• /
• pp.33-62
• /
• 1972

Pitch pine (Pinus rigida Miller) in Korea has become one of the major silvicultural species for many years since it was introduced from the United States of America in 1907. To attain the more rational wood utilization basical researches on wood properties are primarily needed, since large scale of timber production from Pitch Pine trees has now been accomplishing in the forested areast hroughout the country. Under the circumustances, this experiment was carried out to study the wood anatomical, physical and mechanical properties of Pitch Pine grown in the country. Materials used in this study had been prepared by cutting the selected pitch pine trees from the Seoul National University Forests located in Suwon. To obtain and compare the anatomical and physical properties of the different parts of tree such as stem, branch, top and rootwood, this study had been divided into two categories (anatomical and physical). For the anatomical study macroscopical and microscopical features such as annual ring, intercellular cannal, ray, tracheid, ray trachid, ray parenchyma cell and pit etc. were observed and measured by the different parts (stem, branch, root and topwood) of tree. For the physical and mechanical properties the moisture content of geen wood, wood specific gravity, shrinkage, compression parallel to the grain, tension parallel and perpendicular to the grain, radial and tangential shear, bending, cleavage and hardness wree tested. According to the results this study may be concluded as follows: 1. The most important comparable features in general properties of wood among the different parts of tree were distinctness and width of annual ring, transition from spring to summerwood, wood color, odor and grain etc. In microscopical features the sizes of structural elements of wood were comparable features among the parts of tree. Among their features, length, width and thickness of tracheids, resin ducts and ray structures were most important. 2. In microscopical features among the different parts of tree stem and topwood were shown simillar reults in tissues. However in rootwood compared with other parts on the tangential surface distinctly larger ray structures were observed and measured. The maximum size of unseriate ray was attained to 27 cell ($550{\mu}$) height in length and 35 microns in width. Fusiform rays were formed occasionally the connected ray which contain one or several horizontal cannals. Branchwood was shown the same features like stemwood but the measured values were very low in comparing with other parts of tree. 3. Trachid length measured among the different parts of tree were shown largest in stem and shortest in branchwood. In comparing the tracheid length among the parts the differences were not shown only between stem and rootwood, but shown between all other parts of tree. Trachid diameters were shown widest in rootwood and narrowest in branchwood, and the differences among the different parts were not realized. Wall thickness were shown largest value in rootwood and smallest in branchwood, and the differences were shown between root and top or branchwood, and between stem and branch or top wood, but not shown between other parts of tree. 4. Moisture contents of green wood were shown highest in topwood and lowest in heartwood of stem. The differences among the different parts were recognized between top or heartwood and other parts of tree, but not between root and branchwood or root and sapwood. 5. Wood specific gravities were shown highest in stem and next order root and branchwood, but lowest in topwood. The differences were shown clearly between stemwood and other parts of tree, but not root and branchwood. However the significant difference is realized as most lowest value in topwood. 6. In compression strength parallel to the grain compared among the different parts of tree at the 14 percent of moisture content, highest strength was appeared in stem, next order branch and rootwood, but lowest in topwood. 7. In bending strength compared among the different parts of tree at the 14 percent of moisture content clearly highest strength was shown in branchwood, next order stem and root, but lowest in topwood. Though the branchwood has lower specific gravity than stemwood it was shown clearly high bending strength.

• Korean Journal of Agricultural Science
• /
• v.13 no.1
• /
• pp.103-112
• /
• 1986

This study was carried out to prevent the entwining of rice straw on rotary shaft and blade where rice straw was spreaded on paddy field as an organic source before rotary tilling. The rotary tillage was conducted in the paddy field having the soil moisture contents of 30%, 39%, 59% in dry basis and spreaded rice straw (450kg/10a) of 30cm, 45cm, 90cm length with the edged curve angles of rotary blade of $30^{\circ}$, $40^{\circ}$, $50^{\circ}$, $55^{\circ}$ at Yuseung area. And the test were performed on the plot which has width of 30cm and 5cm length and the quantity of entwined rice straw was analized. The test results were summarized as the followings. 1. Entwining phenomenon of rice straw was decreased as the blade edged curve angle increased. The edged curve angle of rotary blade must be determind by considering the characteristics of soil cutting resistance, tilling torque and entwining phenomenon of rice straw. But according to the entwining phenomenon of rice straw only, the edged curve angle of rotary blade should be bigger than $55^{\circ}$ for design. 2. Amount of entwining rice straw was minimized when soil moisture contents was 30 percent (d. b.). It would be better that rotary tillage is performed when soil moisture contents is lower than 30 percent in dry basis. 3. Amount of entwining rice straw was minimized when the length of rice straw was 30cm with $55^{\circ}$ edged curve angle. Therefore, it would be better to chop rice straw as 30cm. 4. Entwining phenomenon of rice straw was decreased as the forward speed decreased. To decrease the entwining rice straw, rotary tillage should be done with forward fist gear (0.35m/s).

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.54 no.2
• /
• pp.203-209
• /
• 2009

Yield monitoring is one of a precision agriculture technology that is used most widely. It is spatial variability analysis of yield information that should be attained with yield monitoring system development. This experiment was conducted to evaluate spatial variability of yield and grain moisture content in rice paddy field, and their relationships to rice productivity. It is necessary to minimize sampling interval for accurate yield map making or to control cutting width of rice combine. Considering small rice plots such as $0.2{\sim}0.4$ ha, optimum size of sampling plot was below 15 m more than 5 m in with and length. In variable rate treatment field, average yield was similar, but yield variation was reduced than conventional field. Gap of yield by another plot in same field was bigger than half of average yield than yield variation was significantly big. Therefore yield measuring flow sensor must be able to measure at least 300 kg/10a more than 1000 kg/10a. Variation of moisture content in same field was not big and spatial dependance did not appear greatly. But, variation between different field is appeared difference according to weather circumstance before harvesting. Change of spatial dependence of yield was not big, because of field variation of moisture content is not big.

• The Journal of the Petrological Society of Korea
• /
• v.17 no.2
• /
• pp.83-94
• /
• 2008

The Pungcheon-myeon, Andong, consists mainly of Precambrian metamorphic rocks, Jurassic igneous rocks, Cretaceous sedimentary rocks (Hasandong, Jinju and Iljik Formations) and Cretaceous igneous rocks (gabbroic rocks, dykes), in which several major faults are developed; Andong fault of ENE trend, which is the boundary fault of the Cretaceous Gyeongsang Basin and the Precambrian-Jurassic basement (Yeongnam Massif), Namhu fault parallel to it, Maebong fault of NNW direction, bow-shaped Gwangdeok fault of ENE direction which is convex toward SSE direction, and Hahoe fault of NNE direction. This paper is researched the geological structures around these major faults by means of the detailed geometric analysis on beddings, joints, faults and drag folds. As a result, a reverse slip faulting of top-to-the SSE movement accompanied with a regional drag folding is recognized from the arrangement of bedding poles measured around the Gwangdeok and Hahoe faults at its northeastern extension, and a zone of Gwangdeok drag fold of 150-300 m width, which is wider at the central and eastern parts of Gwangdeok fault and narrower at its western part and Hahoe fault, is also defined. It indicates that the Hahoe and Gwangdeok faults are a single fault and their movements are coeval unlike the results of earlier reasearchers. And, In this area are recognized two types of faults [(E)NE${\sim}$EW(fault I), WNW${\sim}$NNW (fault II), trending faults] and four types of joints [EW (I), (N)NW (II), NNE (III), NE (IV) trending joints]. These fractures were formed at least through four different events, named as Dn to Dn+3 phases. (1) Dn phase; the formation of joint (I) (Gwangdeok joint) and the intrusion of acidic dykes of EW trend under the compression of EW direction. (2) Dn+1 phase; the formations of joint (II) (Maebong joint), lens-shaped boudinage of acidic dykes, oblique-slip reverse fault (Fault I-Gwangdeok fault) under the compression of (N)NW direction, and the formation of regional zone of Gwangdeok drag fold accompanying the Gwangdeok faulting. (3) Dn+2 phase; those of joint (III), Fault II (Maebong fault) by dextral strike-slip movement of Maebong joint under the compression of NNE direction, and the extension cutting of Dn+1 structures due to the Maebong faulting. (4) Dn+3 phase; the jointing (IV) and the reactivation of Fault II as oblique-slip type with predominant dextral motion which took place under the compression of NE direction. It also suggests that the Maebong fault is not a tear fault deveolped during thrust tectonics of the Andong and Gwangdeok faults but is a post-fault during different tectonic event.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.15 no.3
• /
• pp.198-206
• /
• 1995

Baled silage making(BS) of selected forage crops was discussed during 1991-1993, to determine the best cutting time of the plants for BS production, BS yields and silage quality. Seven species of forage crops and pasture grasses(rye, barley, spring oat, Italian ryegrass, orchardgrass, alfalfa and grass-legume pasture mixtures) were harvested at different stage of growth from young plant to physiological maturity, and baled in a self constructed square baling chamber. Each bales, measured 90cm length, 60cm width and 50cm height, were wrapped with 0.05mrn thick polyethylene plastic film, and stored in stack silo. Each bales were weighed between 15-20 kg in dry matter basis. The effects of pre wilting and formic acid addition on the silage quality of young plant materials, which contained high water concentration, was also evaluated during the experiment. Rye plant including of barley and spring oat were evaluated as a good materials for baled silage making. Fodder rye produced high quality BS with a value of silage quality point 84(Flieg's point) when the plant harvested at stage of greatest dry matter accumulation by 12.64 tonha. The best quality BS of barley was obtained at stage of hard dough to yellow stage by 11.9 ton/ha dry matter yield and 81 point silage quality. Italian ryegrass and pasture grasses including of orchardgrass, alfalfa and grass-legume pasture mixtures procuced also high quality bale silage by harvesting at stage of late blooming. However pre witting operation and formic acid addition was required for BS production of grass materials because of high water contents. Water contents of Italian ryegrass and other pasture species ranged 18.9%(Italian) to 20.8%(alfalfa). Silage quality point of Italian BS harvested at late blooing was increased from 72 to 88 by 1/2-one day pre wilting and 0.3% formic acid treatment. Silage quality of young plant materials of rye and other forage crops, barley and spring oat were also improved markedly through the pre wilting treatment and formic acid addition.