• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.1
• /
• pp.39-45
• /
• 2009

The CRT(Cathode Ray Tube) displays have been substituted for FPDs(Flat Panel Displays) such as LCD(Liquid Crystal Display) and PDP(Plasma Display Panel) because they have a convex surface, large volume and heavy weight. The productivity of FPDs is greatly dependent on the area of thin glass panel with $0.6{\sim}0.8mm$ thickness because FPDs are manufactured by cutting a large-scaled thin glass panel with patterns to the required product dimensions. So FPD's industries are trying to increase the area of thin glass Panel. Through FEM(Finite Element Method) analysis and fluid analysis, we developed an non-contact and air-floating conveyor system which consists of transport-module, distributor, horizontal/vertical changer and controller for the 7th generation glass panel (2,200mm in width, 1,870mm in length and 0.7mm in thickness). The design technology developed in this study can be effectively applied to a conveyor system for a larger-scaled thin glass panel.

• Journal of Mechanical Science and Technology
• /
• v.19 no.5
• /
• pp.1158-1168
• /
• 2005

A shunt from the left ventricle to the left anterior descending artery is being developed for coronary artery occlusive disease, in which the shunt or conduit connects the the left ventricle (LV) with the diseased artery directly at a point distal to the obstruction. To aid in assessing and optimizing its benefit, a computational model of the cardiovascular system was developed and used to explore various design conditions. Computational fluid dynamic analysis for the shunt hemodynamics was also done using a commercial finite element package. Simulation results indicate that in complete left anterior descending artery (LAD) occlusion, flow can be returned to approximately 65% of normal, if the conduit resistance is equal for forward and reverse flow. The net coronary flow can increase to 80% when the backflow resistance is infinite. The increases in flow rate produced by asymmetric flow resistance are enhanced considerably for a partial LAD obstruction, since the primary effect of resistance asymmetry is to prevent leakage back into the ventricle during diastole. Increased arterial compliance has little effect on net flow with a symmetric shunt, but considerably augments it when the resistance is asymmetric. The computational results suggest that an LV-LAD conduit will be beneficial when the resistance due to artery stenosis exceeds 27 PRU, if the resistance is symmetric. Fluid dynamic simulations for the shunt flow show that a recirculating region generated near the junction of the coronary artery with the bypass shunt. The secondary flow is induced at the cutting plane perpendicular to the axis direction and it is in the attenuated of coronary artery.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.11
• /
• pp.4944-4949
• /
• 2012

The purpose of this paper is concerned with a development of air gun for use at work. A air gun is the tool to remove of cutting fluid and workpiece chip in industrial field used machine tool. And it generally is used to shoot a jet of compressed air. Worker must prepare respectively air gun for suction and shooting a jet of compressed air. Therefore we has developed new air gun. In this paper we research for design and analysis of it. The air gun is composed of body, pipe, opening and shutting unit, turning unit, air tube and elements for fabrication. The developed air gun is experimented to confirm the efficiency.

• Journal of Technologic Dentistry
• /
• v.9 no.1
• /
• pp.51-55
• /
• 1987

One of the primary advantages of acrylic resin teeth is their ability to bond chemically to the denture base resins. Fracture od acrylic resin teeth from a maxillary denture, however, is not uncommon. Bonding failures have been attributed to faulty boil-out procedures that fail to eliminate all traces of wax from the ridge lap surfaces of the teeth and to contamination of the ridge lap surface by careless application of tinfoil substitute. Attempts to increase the strength of the bond between acrylic resin teeth and heat-cured denture base resin include grinding the glossy ridge lap surface (in fluid system), painting the ridgelap surface of the teeth with monomer-polymer solution, and cutting retention grooves in the ridge lap surface of the teeth. This latter method has been tested by applying a tensile force in a labial direction to the incisal part of the lingual surface of the acrylic resin teeth. A progressive shear compressive load was applied at an angle to the lingual surface of acrylic resin teeth bonded to denture base acrylic resin. No statistically singificant advantage was derived by preparing retention grooves of different shapes in the ridgelap surface of the denture teeth.

• Economic and Environmental Geology
• /
• v.13 no.2
• /
• pp.104-116
• /
• 1980

The Ulsan mine is one of the largest contact metasomatic magnetite and scheelite deposits in the southeastern part of Korea. Mineralization at the Ulsan mine is localized along the contact between upper Cretaceous volcanic rocks and age unknown limestone which were intruded by 58 m.y. -old biotite-horndlende granite. General zonal sequence of skarn toward crystalline limestone from limestone-volcanics contact is grandite, grandite-salite and salite zones. On the otherhand volcanics origin skarns exhibits zonal sequences toward hornfels from boundary with limestone is garnet, garnet-epidote, and epidote zone. Compositions of garnets and clinopyro xenes are determined by the X-ray diffraction and reflective indecies. Local brecciation of these early skarns were followed by formation of the later skarn as zoned patches, breccia fillings and cross-cutting veins. Paragenetic sequence of late skarn minerals which is exhibited in the zoned patches and veins is an overlapping progression with time from andradite through hedenbergite or actinolite, quartz to calcite deposition. Magnetite metallization followed early formed skarns and pyrite pyrrhoite, sphalerite, galena, tennantite, scheelite and arsenopyrite deposition were simultaneously with hedenbergite, quartz and calcite of late skarn. Filling temperatures of fluid inclusions in calcites range from $160^{\circ}$ to $280^{\circ}C$.

• Archives of Craniofacial Surgery
• /
• v.19 no.2
• /
• pp.157-161
• /
• 2018

A sialocele is a subcutaneous cavity containing saliva, most often caused by facial trauma or iatrogenic complications. In subcondylar fractures, most surgeons are conscious of facial nerve injury; however, they usually pay little attention to the parotid duct injury. We report the case of a 41-year-old man with a sialocele, approximately $5{\times}3cm$ in size, which developed 1 week after subcondylar fracture reduction. The sialocele became progressively enlarged despite conservative management. Computed tomography showed a thin-walled cyst between the body and tail of the parotid gland. Fluid leakage outside the cyst was noted where the skin was thin. Sialography showed a cutting edge of the inferior interlobular major duct before forming the common major duct that seemed to be injured during the subcondylar fracture reduction process. We decided on prompt surgical treatment, and the sialocele was completely excised. A duct from the parotid tail, secreting salivary secretion into the cyst, was ligated. Botulinum toxin was administrated to block the salivary secretion and preventing recurrence. Treatment was successful. In addition, we found that parotid major ducts are enveloped by the deep lobe and extensive dissection during the subcondylar fracture reduction may cause parotid major duct injury.

• Journal of Environmental Science International
• /
• v.15 no.1
• /
• pp.95-100
• /
• 2006

Heat transfer and flow characteristics in a pipe in which the rotating cutting tool for boring a underground pipe without digging were considered in this study. The amount of heat generation due to the friction between the rotating cutter and pipe wall, mixing (low of air and water injected to cool down are the two important factors to design the boring machine Computational fluid dynamics analysis using the Eulerian mixture model and the standard $\kappa-\varepsilon$ turbulence model was used to analyze the complex phenomena in a pipe during the process. Results show that pipe wall temperature decreased with increasing the cooling water inlet velocity. it is also shown that pipe wail temperature was lowered when the cutter rotation speed was increased until 600 rpm. There was no further cooling effect over 600 rpm.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.5
• /
• pp.653-658
• /
• 2011

In general, the purpose of packaging fasteners is a series of management activities to maintain the condition at the time of production until they get delivered to the end user. An automatic packing system for fasteners is consisted of bucket conveyor, slide feeder, vision inspection system, box-magazine conveyor system and automatic packing machine. Also, the automatic packing machine is consisted of six modules including charging device, clamping/opening device, sealing/cutting device, feeding/air-shower device, supplying/adjusting device and device frame, etc. In this paper, we proposed an automatic packing mechanism of the one station concept for packing work of fastener objects where the continuous batch work is performed in a finite space. The proposed one-station packing mechanism has been optimized through mechanical, dynamical, structural and fluid analyses. And it had been manufactured as the prototype of automatic packing machine. The field test for validation of performance was performed directly at the production line of bolt and screw. In the field test, this packing machine showed an efficiency of about 4.5 times the manual operation. It also showed 30% reduction in the consumption of packing materials compared to the manual operation. This automatic packing machine for fastener objects will be commercialized soon.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.14 no.3
• /
• pp.962-975
• /
• 2020

The accurate segmentation of infant brain MR image into white matter (WM), gray matter (GM), and cerebrospinal fluid (CSF) is very important for early studying of brain growing patterns and morphological changes in neurodevelopmental disorders. Because of inherent myelination and maturation process, the WM and GM of babies (between 6 and 9 months of age) exhibit similar intensity levels in both T1-weighted (T1w) and T2-weighted (T2w) MR images in the isointense phase, which makes brain tissue segmentation very difficult. We propose a deep network architecture based on U-Net, called Triple Residual Multiscale Fully Convolutional Network (TRMFCN), whose structure exists three gates of input and inserts two blocks: residual multiscale block and concatenate block. We solved some difficulties and completed the segmentation task with the model. Our model outperforms the U-Net and some cutting-edge deep networks based on U-Net in evaluation of WM, GM and CSF. The data set we used for training and testing comes from iSeg-2017 challenge (http://iseg2017.web.unc.edu).

• 한국전산유체공학회:학술대회논문집
• /
• 2011.05a
• /
• pp.518-522
• /
• 2011

Cartesian grid system has mainly been used in the casting simulation even though it does not nicely represent sloped and curved surfaces. These distorted boundaries cause several problems. A special treatment is necessary to clear these problems. A cut cell method on Cartesian grids has been developed to simulate three-dimensional mold filling Cut cells at a cast-mold interface are generated on Cartesian grids. Governing equations were computed using volume and areas of cast at cut cells. In this paper, we propose a new method that can consider the cutting cells which are cut by casting and mold based on the patial cell treatment (PCT). This method provides a better representation of geometry surface and will be used in the computation of velocities that are defined on the cell boundaries in the Cartesian gird system. Various test examples for several casting process were computed and validated. The analysis results of more accurate fluid flow pattern and less momentum loss owing to the stepped boundaries in the Cartesian grid system were confirmed. We can know the momentum energy at the cut cell is conserved by using the cut cell method. By using the cut cell method. performance of computation gets better because of reducing the whole number of meshes.