• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.24 no.2
• /
• pp.227-234
• /
• 2006

Ministry of construction & transportation is operating for the soil and rock information system and is considered to accurate application of soil conversion factor that is essentially necessary for accurate calculation of earth volume. Since the balance of cutting earth in public work, the plan of spoil bank or borrow pit are directly related to construction costs, accurate calculation of earth volume and efficient scheme of haul are important. As such, this study has provided methods that can acquire information that is more rapid, applicable to job sites, and trustworthy by comparing resultant values of photogrammetry, laser scanning, or inside job site experimentations, and calculated soil conversion factor by applying photogrammetry and laser scanning methods for hard rock that has difficulty in calculating soil conversion factor. The study can provide alternatives that can resolve the problems of unbalanced earth volume that may arise in applying to plans the earth conversion factor that relies on planning books and experience without considering the characteristics of job site earth, and can establish its relevancy by calculating soil conversion factor for hard rock that has relative difficulties in doing inside or job site testing.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.22 no.1
• /
• pp.9-14
• /
• 2002

Evegradies 71' kenaf (Hibiscus cannabinus L.) was grown at 160,000 plants per ha in a volcanic ash soil in Jeju island to determine the optimum frequency of split N application fer forage production. Nitrogen fertilizer was applied with 240 kg/ha, and frequencies of the split N applications were 1, 2, 3, 4 and 5 times. Plant height averaged across two harvests increased from 187 to 201cm as N was split-applied from one to three applications and then decreased to 201cm in five applications. This pattern held for the number of branches and leaves per plant stem diameter and weight of plant per plant. Fresh forage yield increased from 91.8 to 114.2 MT/ha. dry matter yield from 12.70 to 16.6 MT/ha, crude protein yield from 1.75 to 2.48MT/ha, and total digestible nutrients (TDN) yield from 5.39 to 7.63 MT/ha as N was split-applied from one to four applications, and then decreased to 106.6, 15.0, 2.32, and 7.22 MT/ha in five applications, respectively As N was split-applied from one to five applications, crude protein content increased from 13.8 to 15.4%. ether extract content from 4.1 to 5.9%, and TDN content from 42.4 to 48.1%. but crude fiber decreased from 38.2 to 37.1% and crude ash content from 11.5 to 8.6%. Nitrogen free extract content was about 19.0% regardless of cutting height.

• The Journal of the Petrological Society of Korea
• /
• v.14 no.1
• /
• pp.24-37
• /
• 2005

In this study we examined the geomorphological and geological characteristics of the granite landforms in the Iksan area. Moreover we investigated the source areas of stones which are used to build the Mieruksaji west stone pagoda. Joint is most identifiable geomorphological and geological structure in the Iksan area. Direction of J1 joint appears to be N71°E∼EW, and that of J2 joint ranges N20°W∼N20°E. Cross-pattern joint is predominant in the study area, and linen.-pattern vertical joint is also observed. Tor and corestone are easily found as geomorphological features in the study area. Corestones forming for are almost 2∼3 m across and 2∼3 m or over 5 m high. Their hardness is mainly of hammer bounce. Tower-type and castle-type of for are characteristic in the Mireuksan granites. Other geomorphological features such as tafoni, gnamma are also observed in the study area. Petrographical and geochemical features of the stones used for the Mireuksaji west stone pagoda are compared with those of the granites cropped out nearby, and indicate that the stones from the Mieruksaji west stone pagoda are quite similar to the Mireuksan granites. In the Mireuksan we can easily find lots of old traces for rock cutting.

• Food Science and Preservation
• /
• v.11 no.4
• /
• pp.508-515
• /
• 2004

In this study, salting conditions and dehydration methods were investigated. Salting time, concentration and temperature could be considered to variables in salting conditions. The diffused salt amounts to beef jerky depending on time are sharply increased in two hours. This result is caused by the difference decrease of concentration gradient between bulk solution and beef jerky. The increase of salting concentration and temperature resulted also in the increase of a diffused salt. The deeper bulk concentration made diffusion to beef easily with the bigger driving force and the movement of molecules is more active according to temperature increase. Dehydration is conducted with various methods such as natural drying, cold air drying and hot air drying. Comparing with color and texture among the drying methods, cold air drying showed superior quality in color and texture. Beef jerky by cold air drying colored more reddish than other drying methods and good cutting shear stress and tensile strength. In case of hardness and chewiness, hot air drying method showed the highest value, which means the worst texture.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.18 no.4
• /
• pp.37-42
• /
• 2018

With advancements in digital image production technology, the branch of stereoscopic image technology has also been undergoing active development. Accordingly, research and development on cutting-edge display products for mounting stereoscopic images are currently being pursued. There are various problems that can occur when viewing 3D images. Because viewers feel visual fatigue while perceiving the depth of the images provided via an artificial method, a negative human factor such as visual fatigue has become one of the most prominent concerns, especially as it is a factor that affects the ongoing maintenance of 3D images. Therefore, by identifying the factors affecting the depth of the graphic images provided in 2D images, and subsequently using this information to develop an image processing method, we conducted depth-related experiments and analysed them under the assumption that stereoscopic images could be reproduced without visual fatigue. Thus, we analysed the most significant factors related to depth and verified the interactions by performing depth-related factors-based ANOVA variance analysis by differentially applying the texture, colour temperature, and contrast ratio to graphic images. We determined the significance of the factors related to depth and proposed a method to improve depth based on an analysis of the results of the experiments conducted in this study.

• Composites Research
• /
• v.28 no.4
• /
• pp.168-175
• /
• 2015

Recently, the applications of carbon fiber reinforced plastics (CFRPs) have become broader than ever when it comes to such industries as automotive, ships, aerospace and military because of their lightweight-ness and high mechanical properties. Thermosetting plastics like epoxy are frequently used as the binding matrix in CFRPs due to their high hardness, wetting characteristics and low viscosity. However, they cannot melted and remolded. For this reason, thermosetting plastic wastes have caused serious environmental problems with the production of fiber reinforced plastics. Thus, many studies have focused on the carbon fiber reinforced thermoplastics (CFRTPs) and recycling carbon fiber. In this study, recycled carbon fiber (RCF) was prepared from CFRPs using a pyrolysis method, which was employed to separate resin and carbon fiber. The degree of decomposition for epoxy resin was confirmed from thermal gravimetric analysis (TGA) and scanning electron microscope (SEM). The RCF was cut and ground to prepare a carbon fiber composite sheet (CFCS). CFCS was manufactured by applying recycled carbon fibers and various thermoplastic fibers. Various characterizations were performed, including morphological analyses of surface and cross-section, mechanical properties, and crystallization enthalpy of CFCS at different cooling conditions.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.31 no.4
• /
• pp.291-299
• /
• 2005

Objectives : It is well known that cigarette smoking is harzardous to the osseointegration of dental implant, due to the impaired wound healing accompanied by reduced alveolar bone density. The aim of this study is to evaluate the influence of cigarette smoke on the implant osseointegration by the time factor consideration. Materials and methods : Twenty-four male Spraque-Dawley rats (8 weeks, weighting 200 to 250g) were used in this study. In the experimental group, 13 rats were exposed to cigarette smoke, 8 minutes per day during 6 weeks, and 12 rats in the control group were not exposed at any time. RBM (Resorbed blasting media) surfaced implant (diameter 3.3mm, length 5.0mm, AVANA Co., Korea) was placed in the right femur of each rat. Each implant with surrounding bone was prepared with microtome (cutting band 0.2mm$^{(R)}$, EXAKT Co., Germany) after 1 day, 2, 4, 8 and 12 weeks and stained with toluidine blue (1%). Another clinical investigation of each implant was also done at each evaluation time. Results : Clinical investigation around implant fixture showed that there were no significant differences between the control and experimental group. Microscopic observation around implant fixture showed that there were significant differences between the control and experimental group at the initial stage after implant fixture installation. Experimental group showed a decreased bone to implant contact within 4 weeks compared to control group, but showed similar characteristics after 4 weeks. Conclusion : Smoking inhalation effect on the dental implant showed the impaired wound healing by vasoconstriction and decreased intramedullary blood flow at initial stage of osseointegration. This experimental results can be clinically useful to the implant surgery of smoking patients.

• Korean Journal of Oriental Medicine
• /
• v.15 no.2
• /
• pp.51-61
• /
• 2009

Objective: Much has been known that the systematical theory of acupuncture was developed from stone needle as therapeutic tools for orthopedic diseases in ancient times. Stone needle is very old therapeutic method like moxibustion and has been recognized that it was developed since the Stone Age in China so far. In the present study, it was examined for the origination and formation of stone needle based on stone relics of the Stone Age in Korean Peninsular, the medical and geographical literatures. Materials and methods: The facts of stone needle was examined and arranged on the ancient medical or geographical literatures such as The Yellow Emperor's Canon Internal Medicine, Shanhaijing as an ancient geographical book, etc. The clan societies and family related to an origination of stone needle was chased together with their cultural characteristics and origination. The stone relics which have been digged out of historic sites in the North-East Asia were examined for a relevance to stone needle. Results: In The Yellow Emperor's Canon Internal Medicine, it was referred to the stone needle that originated from a fishery zone related to the east coast district in North-East Asia. Through the examination of Shan Hai Jing as an ancient geographical book and its historical reviews, a Go-yi clan society who keep Go's family tree dealt well with the stone needle and jewels including jade in the North-East Asia before the publication periods of The Yellow Emperor's Canon Internal Medicine, and is comprised in the culture of Dong-yi clan society but not the Chinese culture. The obsidian stones, which have been digged out of historical sites in the North-East Asia since the Stone Age, are originated from volcanic areas combined with seashore that seems to be Baekdu mountain district in Korea and Kyushu district in Japan. Furthermore, obsidian stone tools which were found out at Laodung peninsula and the Korean peninsula are archeologically similar to the stone needle with regards to the shape, size and dual-use. In addition, specific obsidian stone tools have been used in orthopedic surgery as well-crafted obsidian blades have a cutting edge up to five times sharper than high-quality steel surgical scalpels. Conclusion: The origin of obsidian stone needle is well corresponded to the explanation about that of the stone needle. It is suggested that the stone needle which influenced in completion of acupuncture and Meridian theory in China seems to be an obsidian stone, and distribution of obsidian stone needle has been closely connected to Dong-yi clan society which are lived in the North-East Asia including Baekdu-mountain district.

• The Journal of Korean Academy of Prosthodontics
• /
• v.41 no.3
• /
• pp.319-324
• /
• 2003

Statement of problem. Adhesives in dentistry playa major role in the success of restorative treatments. In the treatment of all ceramic restoration it is needed to find the adequate bond strength between enamel and dentin. Purpose. The purpose of this study was to evaluate shear bond strength of resin cement bonded to extracted human uncut enamel, cut enamel, and dentin in vitro. Material and methods. Ten freshly extracted anterior teeth without any previous restorative treatments were chosen. The extracted teeth were embedded in PMMA cold acrylic in the shape of a cylinder, 25 mm in diameter by 25 mm in height. The bonding system used was as follow: Uni-Etch (32% phosphoric acid), One-Step adhesive, Duolink resin cement. The specimens were acid etched and rinsed with water. Two layers of One-Step adhesive were coated with a disposable brush on the uncut enamel. VIP curing light at $500mV/cm^2$ was used to cure the adhesive. For cut enamel shear bond test, the specimen used for uncut enamel was further reduced approximately $0.3{\sim}0.5mm$ using a laminate preparation diamond bur (0.3 mm in depth). The specimens were subsequently treated with 320-grit SiC paper followed by 600-grit SiC paper and cleaned with distilled water. The bonding procedure on the cut enamel was same as uncut enamel bonding procedure. For dentin bonding test, the specimen used for cut enamel was further reduced approximately $0.5mm{\sim}1.0mm$ using a laminate preparation diamond bur (0.5 mm in depth of diamond cutting). The amount of reduction was evaluated with the silicone mold. The specimens were subsequently treated with 320-grit SiC paper followed by 600-grit silicon carbon paper and cleaned in distilled water. The bonding procedure on the dentin was same as uncut enamel bonding procedure. All samples were mounted and secured on the Ultradent shear bond test sample holder, and Ultradent restricted shear bond testing device was used with Universal Instron machine until fracture. Analysis of variance (ANOVA) test was performed comparing the result at P<0.05. Multiple comparison (Tukey) was used to compare each groups. Result. The result showed that the mean value in shear bond strength of resin cement bonded to uncut enamel, cut enamel and dentin were 27.04 Mpa, 30.25 Mpa and 26.39 Mpa with respect. Conclusion. Within the limitation of this study, the mean value of the shear bond strength of cut enamel was higher than those of uncut enamel or dentin. However there existed no statistical differences between three different human dentition substrates due to increased adhesive characteristics.

• Korean Journal of Food Science and Technology
• /
• v.36 no.2
• /
• pp.276-282
• /
• 2004

Barley flakes were developed by extrusion cooking using broken kernels, by-products of the barley pearling process. Broken kernels from both non-waxy and waxy barley broken kernels were sufficiently gelatinized at the barrel temperature of over $100^{\circ}C$ and the moisture content of broken kernels of over 35%. Cutting and flaking roll separating properties of pellets prepared from non-waxy barley broken kernels were better than those of waxy barley broken kernels. Characteristics of pellets prepared by extrusion cooking in different mixing ratios of non-waxy and waxy barley broken kernels were investigated. As the mixing ratio of waxy barley broken kernels increased, RVA peak viscosity, apparent viscosity, and yield stress of prepared pellets decreased, while flow behavior index increased. As the mixing ratio of waxy barley broken kernels increased, compressive strength and bulk density of deep-fat fried flakes drastically decreased, and the size of air cells on cross-section increased, and thickness of cell-constituting bodies decreased. Sensory evaluation results showed that acceptability for texture and taste of flakes inclosed as the mixing ratio of waxy barley broken kernels increased, and optimum mixing level of waxy barley broken kernels appeared to be 30-40%.