• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.136-136
• /
• 2009

It is investigated the cut-off frequency of Z-cut quartz microstrip low pass filter by the variation of applied electric field. Designed microstrip filter was simulated using the Ensemble v7.0(Ansoft). As a result of the experiment, the cut-off frequency showed 50 MHz shift when the applied electric field was 3 kV/cm.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2003.03a
• /
• pp.85-92
• /
• 2003

Generally, ordinary portland cement(OPC) is widely used for grouting to reduce permeability of ground under the foundations of structures. But, it is hard to be injected into the microscopic voids, fissures and crevices in soil or rock formation for the OPC material. Therefore new method what is called MSG(Micro Silica Grouting) has been developed recently to improve the weak point of the OPC material. In this case study, in order to verify performance of the MSG's water cut-off, trial injections were performed in rear of CIP(Cast in Place Pile) on the site A(weathered soil) and B(alluvial soil) that are constructed for the subway No. 9 nowadays. To take the proper grouting method of the MSG in the trial injecting, the injections are carried out for grouting types(constant pressure or fixed Quantity) and grouting methods(1.5shot or 2.0shot) and to confirm the effects of water cut-off and the injection range of the MSG, the tests of permeability and indicator(phenolphthalein) response were performed before and after the injection. Through the tests results, we could affirm the effects of water cut-off of the MSG and the injection range for the weathered and alluvial soil layers near the Han River. Finally we could make sure the application of the MSG method in actual construction under the layers.

• Journal of Korean Society of Steel Construction
• /
• v.12 no.2 s.45
• /
• pp.197-207
• /
• 2000

A transient heat transfer analysis and thermo-elastic analysis have been performed for the residual stress distribution on the fillet weldment used by finite element method. Specimen is fabricated single-pass fillet welding. This computation was performed for conditions including surface heat flux and temperature dependent thermo-physical properties using by heat input as parameter. Also, cut-off temperature of residual stress estimation by thermo-elastic analysis is determined. The fillet weldment were measured to determined their residual stress distributions for using hole-drilling method. As result, it was found that large tensile residual stress is about material yield strength, and the numerical simulation results for finite element method similar to residual stresses by hole-drilling method and other exiting research. Also, cut-off temperature is effectively determined by temperature which calculated maximum thermal stress equal to material yield strength.

• Transactions of Materials Processing
• /
• v.14 no.1 s.73
• /
• pp.37-42
• /
• 2005

In order to invstigate the influence of die design variables on the quality of the sheared surface in cutting of sandwich sheet metals, the cut-off operation is carried out, which is the typical shearing process in sheet metal forming technology. For experiments we made the cut-off die which can be easily adjusted for die design variables such as blankholding force, pad force and clearance. The sandwich sheet metals considered are clad304(STS304-Al1050-STS304) and anti-vibration sheet metal. The shearing process is visualized by the computer vision system installed in front of the cut-off die and the sheared surface is measured and quantitatively compared with the help of the optical microscope after cut-off operation. From test results it is shown that the shearing mechanisms are different according the material of which sandwitch sheet metal is composed. The influence of die design variable is explored and we found optimal conditions for both sandwich sheet metals. It is expected that this investigation can be utilized to get the better sheared surface.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1992.05a
• /
• pp.54-57
• /
• 1992

An electro-optical single modulator is fabricated in X-cut LiNbO$_3$by the annealed proton exchange and self-aligned method. First, the effect of annealing is characterized by examining single optical modulator. It is found that by controlling the annealing time, the single optical modulator can be made widely variable. The on-off state of modulator is performed by annealing process and self-aligned electrodes are used in fabricating the single modulator. The optical single modulator has very good figures of merits : the measured on-off switching voltage of about 2.7V.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1992.04a
• /
• pp.109-114
• /
• 1992

This paper describes an effect of operating condition on surface roughness in wire-cut FDM. The experimental values of surface roughness were measured by the test pieces under the condition of changing. On time, Off time, and Feed rate after fixing other conditions. The material of the test pieces is the alloy tool steel(STD 11) and was used after heat treatment. The results are as follows: 1. The surface roughness became rapidly worse according to the increase of On time and Feed rate. 2. The surface roughness became slowly better according to the increase of Off time.

• The monthly packaging world
• /
• s.245
• /
• pp.91-95
• /
• 2013

• Proceedings of the Korean Nuclear Society Conference
• /
• 2002.10a
• /
• pp.445.2-445
• /
• 2002

• The Journal of Engineering Geology
• /
• v.19 no.4
• /
• pp.493-499
• /
• 2009

Recently, the construction of Concrete Faced Rockfill Dam (CFRD) is increasing because rock material resources are plenty in Korea. Bedding zone in the CFRD is necessary enough bearing capacity to support the concrete face slab uniformly and enough impermeability to prevent the loss of fine soils in case of leakage from the concrete slab face. Therefore, cut-off the water leakage in bedding zone securely is the key factor influencing the safety of CFRD. Tested materials satisfied with the specification of particle size distribution at the Bedding Zone area are chosen for conducting permeability tests, which are done to evaluate the property of cut off the materials. Based on the test results, the effects of cut off the materials are investigated by considering the coefficient of permeability, the soil particle distribution, and the dry unit weight. Especially, the relationships between coefficient of permeability with effective size(D10), dry unit weight, and weight passing percent the No.4 sieve are suggested, and also the variation of coefficient of permeability with time are proposed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.809-812
• /
• 2001

We were fabricated of NiCr thin film resistors on A1$_2$O$_3$and SiO$_2$/Si substrates by dc magnetron sputtering system. The AC characteristics of resistors were studied. The cut-off frequency were found >10 MHz for the resistors with 39 ohm value of Alumina substrates, but the cut-off frequency were found 400 kHz for the resistors with 168 ohm value of SiO$_2$/Si substrates. In high frequency applications, the substrate selection is the most important factor.