• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.05a
• /
• pp.1100-1105
• /
• 2007

In the gas supply duct, the gas leakage caused by the impact of the construct equipment is serious problem. The identification of the impact position is an important issue and an engineering work. For the basic research of this problem, the principle studies for the acoustic wave propagation in a gas duct are proceeded in this paper. This principal work is based on the identification of the cut-off frequency associated with major modes of the gas duct theoretically and experimentally. The cut-off frequency is confirmed by STFT and cross-correlation function is used to identify the leakage position.

• Journal of the korean Society of Automotive Engineers
• /
• v.10 no.2
• /
• pp.54-60
• /
• 1988

This paper presents a study of tool-life equation on cut-off test by the statistical approach, referred to as response surface methodology instead of a conventional one-variable at a time method. It is the merit of response surface methodology that the test time is reduced to minimize the size and accurate analysis can be done. The reliability of such an equation can also be estimated. Two independent variables, cutting speed and feed rate, were investigated. A first order modeling equation is presented in this project. The results of this study are as follows that tool-life in cut-off operation is affected by cutting speed more than feed, and first order tool-life predicting equations are in good agreement with experimental results.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.27 no.10
• /
• pp.75-79
• /
• 2013

The automatic quiescent power cut-off receptacles(QPCR from now on) have achieved a noticeable energy saving so far. The government is preparing a new code for wider promotion of the QPCRs. This paper presents a new QPCR that adopts the latch relay instead of the conventional coil-operated relay. Measurement results of the prototype have shown up to 0.22W improvement of quiescent power compared with existing products.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.3
• /
• pp.533-541
• /
• 2001

In this paper, we proposed lowpass filter using all-pass sums of flat delay characteristics. this filter consisted of all-pass filter of parallel structure, the general analog filter is impossible to adjust the phase and the delay, using the Proposed filter, it has advantage to adjust them. And, we compared and analyzed this filter with passband width and magnitude characteristics, and the relation of group delay characteristics and cut-off frequency. Also, in order to obtain desired cut-off frequency, forming the weighing, we obtained desired cut-off frequency and group delay characteristics.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.8
• /
• pp.797-804
• /
• 2008

In the gas supply pipe, the gas leakage caused by the impact of the construct equipment is serious problem. The identification of the impact position is an important issue and an engineering work. For the basic research of this problem, the principle studies for the acoustic wave propagation in a gas pipe are proceeded in this paper. This principal work is based on the identification of the cut-off frequency associated with major modes of the gas pipe theoretically and experimentally The cut-off frequency is confirmed by STFT and cross-correlation function is used to identify the leakage position.

• Journal of Power System Engineering
• /
• v.17 no.1
• /
• pp.58-63
• /
• 2013

The aerodynamic performance of double inlet sirocco fan is strongly dependent upon the design factors of impeller and scroll. In this paper, the change of scroll size was adopted to investigate the aerodynamic performances of double inlet sirocco fan and indoor PAC. Especially, a scroll expansion angle and a cut-off clearance ratio were considered to change the scroll size. In addition, the installation depth between double inlet sirocco fan and indoor PAC was considered. As a result, the total pressure efficiency of double inlet sirocco fan shows about 62%~73% according to the change of scroll expansion angles. Moreover, the flowrate performance of indoor PAC is the best at the condition of a scroll expansion angle of 8°, an installation depth of 15 mm and a cut-off clearance ratio of 8%.

• Particle and aerosol research
• /
• v.8 no.1
• /
• pp.1-8
• /
• 2012

In this study, the collection efficiency of inertial impactors was numerically simulated by employing the statistical Lagrangian particle tracking(SLPT) model. The SLPT model was proven to be correct in predicting the impactor collection efficiency, when the numerically obtained collection efficiencies were compared with the experimental data of Marple et al.(1987) at normal pressure level and the experimental data of $Marjam{\ddot{a}}ki$ et al.(2000) at low pressure level. Based on the validation results, balloon-borne impactors with the cut-off sizes of $1{\mu}m$, $2.5{\mu}m$, and $10{\mu}m$ were designed. Then, the sampling flowrates of the inertial impactors, required to keep the cut-off sizes constant at different pressures and temperatures, were estimated according to the altitude.

• Journal of Korean Ophthalmic Optics Society
• /
• v.7 no.1
• /
• pp.35-38
• /
• 2002

Ferrite thin film with glass substrate was prepared by ferrite plating method in order to make sunglass which cut off ultraviolet and electromagnetic field. It has single phase of polycrystalline spinel structure and has gloss like as mirror and has hardness without scratch by scraping with nail. The transmittance of ferrite thin film is lowered near 400nm manifestly, which shows that the ferrite thin film was cut off ultraviolet successfully. Therefore, the sunglass with ferrite plating is use of cut of ultraviolet and electromagnetic field.

• Journal of Korean Society of Steel Construction
• /
• v.8 no.4 s.29
• /
• pp.19-29
• /
• 1996

In this paper, it is presumed that the stress time history was generated by simulation method and investigated compatibility in regard to the reappearance of stress time history. In this procedure, the identified frequency distribution of stress range of the steel railroad bridge varies with the rational values of cut off point and bar width. Thus, we show variable aspect of the equivalent stress range results from change of cut off point and bar width. In addition, we analyze the variable of RMC and RMS model due to the cut off point and bar width of the measured stress history which influencs the prediction of fatigue life in the steel railroad bridge. The simulated stress time history is carried out by the superposition method incorporating the vertical load with rotation moment obtained from the Hermition interpolation function, and compared with developing stress results from measured maxi mum stress. Through this study, we can estimate the remaining fatigue life from a safety point of view and comparative accuracy.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.1
• /
• pp.123-130
• /
• 1996

The procedure on the design of a new tungsten cabide throw-away cutting tool system for deep grooving or cut-off machining is suggested. For relieving the maximum stress level at the corner radius of the blade holder, the finite element method is used. Also the pulling test device is proposed for measuring the holding force of the insert between the blade holder and the insert considering the materials in contact and configuration parameters of the holder.