• Journal of Surface Science and Engineering
• /
• v.26 no.2
• /
• pp.63-70
• /
• 1993

The mechanical properties of ferrite-martensited dual phases steels are affected by the microstructural factors, such as martensited volume fractions, ferrite grain size, strength ratio, connectivity, etc. Two phase alloys are technologically important. However, there is a lack of understanding as to stress-strain behavior of dual phase alloy in terms of stress-strain behavior of each component phases. The lack of the understanding stems from the complex deformation behavior of two phase alloys. The aim of this study is to rationalize stress-strain behavior of dual phase alloy in terms of the stress-strain behavior of component phase by systematically considering all the factors listed above. It was found that for a given martensite volume fraction, the calculated stress-strain curve was higher for a finer particles size than for a coarse particle sized within the range of the strains considered, and this behavior was seen for all the different volume fraction alloys considered. The calculated stress-strain curves were compared with corresponding experimental curves, and in general, good agreement was found. The maximum difference in flow stress between the calculated and the experimental results occurs at the nearly beginning of the plastic deformation.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.6
• /
• pp.1529-1540
• /
• 1993

The quenching of steels by water is one of the imprtant problems in the applications of heat treatment, but the fundamental researches by way of theoretical approaches have not been satisfactorily improbed yet. This study aimed at measuring the exact subcooled transient boiling curve for cylindrical specimens and at conducting the analytical researches into the prediction of cooling curves, including the latent heat of phase transformation of steel. Experiments of quenching were made with cylindrical specimens of carbon steel S45C of diameters from 12 to 30 mm and with Cu specimens of 12 mm diameter respectively. The internal temperature of specimens during the quenching process was measured by C-A sheathed thermocouple. The heat fluxes were numerically calculated by the numerical method of inverse heat conduction problem, using the measured inner temperature of specimen as a boundary condition. In case of ${\Delta}T_{sub}=80K$, $q_{s}$ is as follows $q_{s}=2.02{\times}10^{5}{\Delta}T_{set}^{0.05}:{\Delta}T_{set}\le500K.$ And the numerical analysis of unsteady heat conduction during the quenching process was made and the cooling curves were calculated by TDMA method.

• Ocean and Polar Research
• /
• v.33 no.3
• /
• pp.309-319
• /
• 2011

This is a preliminary study of the feasibility of obtaining reliable tidal current harmonic constants, using one month of current observations, to verify the accuracy of a tidal model. An inference method is commonly used to separate out the tidal harmonic constituents when the available data spans less than a synodic period. In contrast to tidal constituents, studies of the separation of tidal-current harmonics are rare, basically due to a dearth of the long-term observation data needed for such experiments. We conducted concurrent and monthly harmonic analyses for tidal current velocities and heights, using 2 years (2006 and 2007) of current and sea-level records obtained from the Tidal Current Signal Station located in the narrow waterway in front of Incheon Lock, Korea. Firstly, the l-year harmonic analyses showed that, with the exception of $M_2$ and $S_2$ semidiurnal constituents, the major constituents were different for the tidal currents and heights. $K_1$, for instance, was found to be the 4th major tidal constituent but not an important tidal current constituent. Secondly, we examined monthly variation in the amplitudes and phase-lags of the $S_2$ and $K_1$ current-velocity and tide constituents over a 23-month period. The resultant patterns of variation in the amplitudes and phase-lags of the $S_2$ tidal currents and tides were similar, exhibiting a sine curve form with a 6-month period. Similarly, variation in the $K_1$ tidal constant and tidal current-velocity phase lags showed a sine curve pattern with a 6-month period. However, that of the $K_1$ tidal current-velocity amplitude showed a somewhat irregular sine curve pattern. Lastly, we investigated and tested the inference methods available for separating the $K_2$ and $S_2$ current-velocity constituents via monthly harmonic analysis. We compared the effects of reduction in monthly variability in tidal harmonic constants of the $S_2$ current-velocity constituent using three different inference methods and that of Schureman (1976). Specifically, to separate out the two constituents ($S_2$ and $K_2$), we used three different inference parameter (i.e. amplitude ratio and phase-lag diggerence) values derived from the 1-year harmonic analyses of current-velocities and tidal heights at (near) the short-term observation station and from tidal potential (TP), together with Schureman's (1976) inference (SI). Results from these four different methods reveal that TP and SI are satisfactorily applicable where results of long-term harmonic analysis are not available. We also discussed how to further reduce the monthly variability in $S_2$ tidal current-velocity constants.

• Proceedings of the IEEK Conference
• /
• 2003.07c
• /
• pp.2589-2592
• /
• 2003

In this paper, a robust mixed H$_2$/H$\_$$\infty$/ output feedback control method is applied to the design of loop filter for PLL carrier phase tracking. The proposed method successfully copes with large S-curve slope uncertainty and a significant decision delay in the closed-loop that may exist In modern receivers due to a convolutional decoder or an equalizer. The objective is to design an output feedback controller which minimizes the H$_2$performance while satisfying the H$\_$$\infty$/ performance to guarantee the gain margin and phase margin for linear time invariant(LTI) polytopic uncertain systems. LMIs based approach is given to solve this problem. We can verify the H$\_$$\infty$/ performance satisfaction and minimize the phase detector error through the simulation result.

• YAKHAK HOEJI
• /
• v.36 no.6
• /
• pp.563-569
• /
• 1992

The sorption and desorption properties of four different solid adsorbents were evaluated for the trace enrichment of ibuprofen from biological samples. Chromosorb 107 gave the highest dynamic adsorption coefficient. Among the organic solvents examined, acetone gave the highest desorption coefficient. Using the Chromosorb 107 column, the optimum elution volume of the eluting solvent was evaluated from the breakthrough curve of ibuprofen. The usefulness of Chromosorb 107 as the solid adsorbent and acetone as the eluting solvent was examined for the solid-phase extraction of ibuprofen from serum in the concentration range of $20{\sim}40\;{\mu}g/ml$.

• The Bulletin of The Korean Astronomical Society
• /
• v.38 no.2
• /
• pp.56.2-56.2
• /
• 2013

We study the three-dimensional genus topology of large-scale structure using the CMASS Data Release 11 sample of the SDSS-III Baryon Oscillation Spectroscopic Survey (BOSS). The CMASS sample yields a genus curve that is characteristic of one produced by Gaussian random-phase initial conditions. The data thus supports the standard model of inflation where random quantum fluctuations in the early universe produced Gaussian random-phase initial conditions. Modest deviations in the observed genus from random phase are as expected from the nonlinear evolution of structure. We construct mock SDSS CMASS surveys along the past light cone from the Horizon Run 3 (HR3) N-body simulations, where gravitationally bound dark matter subhalos are identified as the sites of galaxy formation. We study the genus topology of the HR3 mock surveys with the same geometry and sampling density as the observational sample, and the observed genus topology to be consistent with LCDM as simulated by the HR3 mock samples.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.3C no.2
• /
• pp.43-47
• /
• 2003

Lead zirconate titanate (PZT) thin films were fabricated by the pulsed laser ablation deposition (PLAD) method onto Pt/Ti/SiO$_2$/Si substrates. Crystalline phases as well as preferred orientations in PZT films were investigated by X-ray diffraction analysis (XRD). The well-crystallized perovskite phase and the (101) preferred orientation were obtained by two-step annealing at the conditions of $650^{\circ}C$, 1 hour. It was found that the temperature for the pulsed laser ablated PZT films annealed via a two-step annealing process can be reduced 20$0^{\circ}C$ compared to that of the conventional three-step annealing temperature profile for enhancing the transformation of the perovskite phase. The remanent polarization and the coercive field of this film were about 20 $\mu$C/$\textrm{cm}^2$ and 46 kV/cm, while the dielectric constant and loss values measured at 1 KHz were approximately 860 and 0.04, respectively. The interesting phenomena of this film, such as vertical shift in hysteresis curve, are also discussed.

• Communications for Statistical Applications and Methods
• /
• v.6 no.2
• /
• pp.543-564
• /
• 1999

The principal aim of a sequential phase I clinical trial in which the toxicity reponses of a group of patient(s) determine the dose level of the next patient(s) group is to estimate the maximal tolerated dose(MTD) of a new drug, In this paper we compared with a simulation study the performance of the MTD estimates that are determined by a stopping rule in a design and also those that are determined by analyzing the data after a clinical trial is terminated. To the latter belong the mean median mode and maximum likelihood estimates. For the Standard Methods the stopping rule MTD is quite inefficient but the median MTD has a best efficiency and is robust with respect to the three different toxicity curves. The problem of non-convergence of MLE MTD is severe. A more improved MTD estimate is produced by combining the advantages of the various MTD estimates and its efficiency is better than the single median MTD estimate especially for the toxicity curve of an unlucky choice of dose levels. The simulation results suggest that simple types of phase I designs can be combined with relatively standard analytic techniques to provide a more efficient MTD estimate.

• Proceedings of the Polymer Society of Korea Conference
• /
• 2006.10a
• /
• pp.288-288
• /
• 2006

Natural rubbers (NR) reinforced by multi-wall carbon nanotubes (MWCNT) was found to show extraordinary improvement of mechanical property. We speculated that this was owing to the interfacial phase that surrounded CNT and investigated about the phase by atomic force microscopy (AFM). Using force modulation mode and force-distance curve analyses, we succeeded in obtaining the information of its nanometer-scale rheological property. We found that was actually surrounded by the interfacial phase, that had softer modulus than NR matrix.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.9 no.5
• /
• pp.564-571
• /
• 1985

The estimation of fracture toughness in inhomogeneous material is still insufficient because it is difficult to get information of fracture initiation at the crack tip. Therefore, martensite-ferrite dual phase steel was prepared for a model material and micro-fracture behavior was investigated in the region of pre-fatigue crack in order to understand the characteristic of fracture resistance in inhomogeneous materials. In the case of severely inhomogeneous state, micro-fracture appearance is not distributed homogenously so that the estimation of fracture toughness is hardly possible. On the other hand when the grain size is refined or the strength of martensite is lowered, micro-fracture appearance is distributed homogenously and fracture toughness remarkably increases.