• Journal of Sensor Science and Technology
• /
• v.6 no.5
• /
• pp.407-413
• /
• 1997

The crystallized CuPc(copper phthalocyanine) film on a p-type <100> Si substrate is prepared at the substrate temperature of $300^{\circ}C$ by thermal evaporation. X -ray diffraction analysis showed the CuPc film to have a-axis oriented structure. For the measurement of photovoltaic characteristics of the CuPc/Si film and the Si substrate, a transverse current-voltage (I-V) curve is observed. In the dark, the Au/Si junction is shown to be ohmic contact. However, under illumination, a photovoltaic effect is not observed. The I-V curve in the dark indicates that the CuPc film on Si may form an ohmic contact. Since the CuPc film is a p-type semiconductor, the CuPc/p-Si junction has no barrier at the interface. Under illumination, the CuPc/Si junction shows a large photocurrent comparing with that of the wafer. The result indicates that the CuPc layer plays an important role in the photocarrier generation under red illumination (600 nm). The CuPc/Si film shows the photo voltaic characteristics with a short-circuit photocurrent ($J_{sc}$) of $4.29\;mA/cm^{2}$ and an open-circuit voltage ($V_{oc}$) of 12 mA.

• Journal of Sericultural and Entomological Science
• /
• v.13 no.2
• /
• pp.123-133
• /
• 1971

The author is the first man who tried to use an anesthetic on insect specially for silkworm in orde to evaluate the silkworm health and silk yielding ability and the obtained results are as followings. 1. The necessary ether vapor induction for narcosis on silkworms is varied by the glowth of the silkworm which the larger worm is, the longer induction is required. For instance, it was 2∼3 minutes for the worms of third day fifth instar silkworm in case use of ether anesthetic. 2. The longer anesthetic induction for silkworms, the longer recovery needs from anesthesia. In case five minutes ether vapor induction, silkworms recovered narcosis during in 5∼130 minutes which had varied very much by the health variation. 3. The ether induction caused silkworm to vomit digestive juice from a few per cent of the worms, but the chloroform induction showed majority of the worms to vomit the digestive juice out of mouth. So, the ether was found as better anesthetic for silkworms. 4. When ether induction last more than 20∼30 minutes, the recovered silkworms can eat mulberry, but when it gets more than three hours they can not eat mulberry. And when it last more than ten minutes, the silkworm may eat mulberry leaf, but they can not spinn cocoon properly. 5. In case five minutes ether induction for silkworms on third day fifth instar, the stronger variety is, the rallier recovered from narcosis. 6. The recovering duration from narcosis varies regarding with each worm health which shows Poisson′s distribution even in a same variety silkworm. 7. The female worms recover from narcosis earlier than male worms which means the female worm is stronger than male one. 8. The later recovered silkworm from narcosis spinned more rich cocoon silk and ended with smaller pupae weight. Such a tendency showed until at some recovery duration, then the silk yield droped down on the worms recovered in more longer duration. The author (Choe) had named such a relation curve as "Silk Yield Curve against Silkworm Health." 9. The silk yield or cocoon layer ratio had varied from 13 to 27% even in a same worm varity cocoon which showed serious variation and call attention carefulness for the duplication work of a variety silkworm eggs. 10. Not always the rich silk yielding worm is the best worm during the silkworm selection and it should be considered with the silkworm health evaluation. 11. At present situation, only specific breeding expert is allowed to join in the selection service because of need many years experience by use of visual observation, but the ether anesthesia method may help such an evaluation with more accuracy and easy way even for the people in fresh on the field. 12. The effect of the narcosis on the silkworm for the next generation or hybrid worm will be reported in next publication.

• Journal of Radiation Industry
• /
• v.17 no.4
• /
• pp.471-479
• /
• 2023

In In-situ radioactivity measurement techniques, efficiency calibration models use predefined models to simulate a sample's geometry and radioactivity distribution. However, simplified efficiency calibration models lead to uncertainties in the efficiency curves, which in turn affect the radioactivity concentration results. This study aims to develop an efficiency calibration optimization methodology to improve the accuracy of in-situ gamma radiation measurements for byproducts from industrial facilities. To accomplish the objective, a drive mechanism for rotational measurement of an byproduct simulator and a sample was constructed. Using ISOCS, an efficiency calibration model of the designed object was generated. Then, the sensitivity analysis of the efficiency calibration model was performed, and the efficiency curve of the efficiency calibration model was optimized using the sensitivity analysis results. Finally, the radiation concentration of the simulated subject was estimated, compared, and evaluated with the designed certification value. For the sensitivity assessment of the influencing factors of the efficiency calibration model, the ISOCS Uncertainty Estimator was used for the horizontal and vertical size and density of the measured object. The standard deviation of the measurement efficiency as a function of the longitudinal size and density of the efficiency calibration model decreased with increasing energy region. When using the optimized efficiency calibration model, the measurement efficiency using IUE was improved compared to the measurement efficiency using ISOCS at the energy of ²²⁸Ac (911 keV) for the nuclide under analysis. Using the ISOCS efficiency calibration method, the difference between the measured radiation concentration and the design value for each simulated subject measurement direction was 4.1% (1% to 10%) on average. The difference between the estimated radioactivity concentration and the design value was 3.6% (1~8%) on average when using the ISOCS IUE efficiency calibration method, which was closer to the design value than the efficiency calibration method using ISOCS. In other words, the estimated radioactivity concentration using the optimized efficiency curve was similar to the designed radioactivity concentration. The results of this study can be utilized as the main basis for the development of regulatory technologies for the treatment and disposal of waste generated during the operation, maintenance, and facility replacement of domestic byproduct generation facilities.

• Journal of Korea Water Resources Association
• /
• v.53 no.7
• /
• pp.545-555
• /
• 2020

A feasibility modeling for potential hydroelectric dam site selection was suggested using 1 sec ASTGTM (ASTER Global Digital Elevation Model) and Terra/Aqua MODIS (Moderate Resolution Imaging Spectroradiometer) derived land use (MCD12Q1) data. The modeling includes DEM pre-processing of peak, sink, and flat, river network generation, watershed delineation and segmentation, terrain analysis of stream cross section and reservoir storage, and estimation of submerged area for compensation. The modeling algorithms were developed using Python and as an open source GIS. When a user-defined stream point is selected, the model evaluates potential hydroelectric head, reservoir surface area and storage capacity curve, watershed time of concentration from DEM, and compensation area from land use data. The model was tested for 4 locations of already constructed Buhang, BohyunMountain, Sungdeok, and Yeongju dams. The modeling results obtained maximum possible heads of 37.0, 67.0, 73.0, 42.0 m, surface areas of 1.81, 2.4, 2.8, 8.8 ㎢, storages of 35.9, 68.0, 91.3, 168.3×10⁶ ㎥ respectively. BohyunMountain and Sungdeok show validity but in case of Buhang and Yeongju dams have maximum head errors. These errors came from the stream generation error due to ASTGTM. So, wrong dam watershed boundary limit the head. This study showed a possibility to estimate potential hydroelectric dam sites before field investigation especially for overseas project.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.18 no.1
• /
• pp.57-65
• /
• 2010

Two types of microbial fuel cells(MFC) were continuously operated using synthetic wastewater. One was conventional two-chambered MFC using proton exchange membrane(PEM-MFC), the other was upflow type membraneless MFC(ML-MFC). Graphite felt was used as a anode in PEM-MFC. In membraneless MFC, two MFCs were operated using porous RVC(reticulated vitreous carbon) as a anode. Graphite felt was used as a cathode in all experiments. In experiment of PEM-MFC, the COD removal rate based on the surface area of anode was about $3.0g/m^2{\cdot}d$ regardless of organic loading rate. And the coulombic efficiency amounted to 22.4~23.4%. The acetic acid used as a fuel was transferred through PEM from the anodic chamber to cathodic chamber. The COD removal rate in ML-MFC were $9.3{\sim}10.1g/m^2{\cdot}d$, which indicated the characteristics of anode had no significant effects on COD removal. Coulombic efficiency were 3.6~3.7 % in both cases of ML-MFC experiments, which were relatively small. It was also observed that the microbial growth in cathodic chamber had an adverse effects on the electricity generation in membraneless MFC.

• Korean Journal of Food Science and Technology
• /
• v.31 no.5
• /
• pp.1315-1323
• /
• 1999

The antimicrobial effects of ethanol and organic acids(acetic, citric, lactic. propionic, tartaric acid), either alone or in combination against four foodborne microorganisms (Listeria monocytogenes, Salmonella typhimurium, Staphylococcus aureus and Escherichia coli O157:H7) in tryptic soy broth were determined. Area under the growth curve, minimum generation time, maximum growth rate, and detection time were measured by using automated turbidometer Bioscreen(Labsystem, Finland), for 24 hr at $30^{\circ}C$. All microorganisms were not grown at 7% ethanol in the media. The 0.1% propionic acid showed the strongest inhibitory effects against S. aureus, L. monocytogenes and E. coli O157 : H7 compared with other organic acids, whereas 0.01% organic acids did not show significant inhibitory effect against microorganisms tested (p > 0.01) except S. aureus. The combination of 1% ethanol and 0.01% organic acids were significantly more effective than alone on growth of S. aureus and L. monocytogenes(p < 0.01).

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.6
• /
• pp.24-33
• /
• 2000

Switching behaviour of the ferroelectric thin film and device characteristics of the MFSFET(Metal-Ferroelectric-Semiconductor FET) are simulated with taking into account the accumulation of oxygen vacancies near interface between the ferroelectric thin film and the bottom electrode caused by the progress of fatigue. In our switching model, relative switched charge is 0.74 nC before fatigue, but after the progress of fatigue it reduces to 0.15 nC with the generation of oxygen vacancies. It indicates that the generation of oxygen vacancies strongly suppresses polarization reversal. $C-V_G\;and\;I_D-V_G$ curves in our MFSFET device model exhibit the memory window of 2 V and show the accumulation, the depletion and the inversion regions in capacitance characteristic clearly. The difference of saturation drain current of the device before fatigue in shown by the dual threshold voltages in $I_D-V_G$ curve as 6nA/$cm^2$ and decreases as much as 50% after fatigue. Decrease of the difference of saturation drain currents by fatigue implies that the accumulation of oxygen vacancies with the fatigue should be avoided in the device application. Our simulation model is expected to play an important role in estimation of the behavior of MFSFET device with various ferroelectric thin films.

• Journal of IKEEE
• /
• v.21 no.4
• /
• pp.368-374
• /
• 2017

In this Paper, we developed a low power type LED security light using LED lighting that substitutes a 220[V] commercial power source for a solar cell module instead of a halogen or a sodium lamp. in addition, a PWM type drive control circuit is designed to minimize the heat generation problem and the drive current of the LED drive controller. in developed system, The light efficiency measurement value is 93.6[lm/W], and a high precision temperature sensor is used inside the controller to control the heat generation of the LED lamp. In order to eliminate the high heat generated from the LED lamp, it is designed to disperse quickly into the atmosphere through the metal insertion type heat sink. The heat control range of LED lighting was $50-55[^{\circ}C]$. The luminous flux and the lighting speed of the LED security lamp were 0.5[s], and the beam diffusion angle of the LED lamp was about $110[^{\circ}C]$ by the light distribution curve based on the height of 6[m].

• Parasites, Hosts and Diseases
• /
• v.29 no.1
• /
• pp.67-86
• /
• 1991

In order to determine the seasonal prevalence and population dynamics of Culex tritaeniorhynchus in relation to the epidemics of Japanese encephalitis, and ecology of these vector mosquito in Kyungpook Province, Korea, studies were con- ducted during the Period of 7 years from 1984 to 1990. Cx. tritaeniorhynchus first collected in June between 4th and 28th, and trapped in large numbers during the period from mid-August to early September, showed a simple sharply pointed one-peaked curve. There was a gradual decrease from mid-September, with a very small number of them collected until early October in every year. The average number of Cx. tritaeniorhynchus rapidly decreased after 1985, and the number became particularly low in 1989. The highest population density, which was observed in August during the initial three years, was found to be delayed in the following years, accompanied by a decrease in the number of mosquitoes. In the trend of nocturnal activity of Cx. tritaeniorhynchus, with oncoming darkness they become very active, gradually decreasing in activity toward mid night, but slightly increasing toward dawn. The immature stages of Cx. tritaeniorhynchus were first found in rice fields contributing to peak adult densities in mid-July. The highest average densities of Cx. trisaeniorhynchus was 14,900 per m2 on mid-August 19th. The larval Cx. tritaeniorhynchus showed high resistance levels and resistance ratios against 5 organophosphorus compounds. In the adult horisontal life table characteristics of Kyungsan colonies of Cx. tritaeniorhynchus under insectary condi- tions, life expectancy was 28.3 days for males and 59.8 days for females. The net reproductive rate was 7.8 and generation time was 25.6 days.

• Journal of the Microelectronics and Packaging Society
• /
• v.28 no.1
• /
• pp.47-54
• /
• 2021

For the bonding of smaller PCB solder bumps of less than 100 microns, an experiment was performed to make up a tin plating solution and find plating conditions in order to produce a bump pattern through tin electroplating, replacing the previous PCB solder bumps process by microballs. After SR patterning, a Cu seed layer was formed, and then, through DFR patterning, a pattern in which Sn can be selectively plated only within the SR pattern was formed on the PCB substrate. The tin plating solution was made based on methanesulfonic acid, and hydroquinone was used as an antioxidant to prevent oxidation of divalent tin ions. Triton X-100 was used as a surfactant, and gelatin was used as a grain refiner. By measuring the electrochemical polarization curve, the characteristics of organic additives in Triton X-100 and gelatin were compared. It was confirmed that the addition of Triton X-100 suppressed hydrogen generation up to -1 V vs. NHE, whereas gelatin inhibited hydrogen generation up to -0.7 V vs. NHE. As the current density increased, there was a general tendency that the grain size became finer, and it was observed that it became finer when gelatin was added.