• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2000.11a
• /
• pp.341-346
• /
• 2000

The effect of OTS(octadecyltrichlorosilane) SAM(self-assembled monolayer) on the micro-adhesion has been studied. OTS SAM was formed on the Si(100) surface and SPM (scanning probe microscope) tips with different radius of curvature were fabricated by a series of masking and etching processes. Pull-off forces of different tips on Si and OTS SAM surfaces were measured by SPM in different relative humidities. The surface of OTS SAM was changed to hydrophobic surface and the micro-adhesion force of OTS SAM was lower than that of pure Si. As the tip radius of curvature and the relative humidity increased. the micro-adhesion force increased. Based on the test results. the main parameter affected to the micro-adhesion was absorbed humidity on the surface.

• Tribology and Lubricants
• /
• v.17 no.4
• /
• pp.276-282
• /
• 2001

Nano adhesion between SPM (scanning probe microscope) tips and 075 (octadecyltrichlorosilane) SAM (self-assembled monolayer) was experimentally studied. Tests were performed to measure the nano adhesion and friction in both AFM(atomic force microscope) and LFM(lateral force microscope) modes in various conditions of relative humidity. OTS SAM was formed on Si-wafer (100) surfaces, and Si$_3$N$_4$ tips of different radius of curvature were used. When the surface was hydrophobic, the adhesion and friction forces were found lower than those of bare Si-wafer. Results also showed that micro-adhesion force increased as the relative humidity and the tip radius of curvature increased. The main parameter for affecting the micro-adhesion was found absorbed humidity on the contact surface. These results were discussed with the JKR model and a capillary force caused by absorbed water.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.12
• /
• pp.1301-1309
• /
• 2008

The curved portion fur each section running safety evaluation interpretation according to the track condition for improving the curved portion passage rate of a vehicle by using the multibody analysis model of the Saemaeul train was carried out. As a result, The excess of cant reaches the bad effect to the running safety in case the radius of curvature is small. In case the radius of curvature was large, we could confirm that the deficiency of cant reached the bad effect to the running safety. In the curved portion, the circular curve section most badly showed the running safety. The deficiency of curve length reaches the bad to the running safety. In the curved portion, the circular curve section most badly showed the running safety. Therefore the track condition(cant, transition curve length, etc) can reach the bad effect to the running safety of a vehicle, the exact design is required.

• Journal of the Semiconductor & Display Technology
• /
• v.20 no.4
• /
• pp.114-118
• /
• 2021

In this research, the dimensional error of the measured specimen according to the measurement method was analyzed for the length, angle, radius of curvature and diameter using a projector which is used in industry. One-way analysis was performed on each data tested 30 times using a statistical technique. Through the experiment, it was found that an error occurred in each data when measuring the length and radius of curvature according to the measurement method, and the null hypothesis that no error occurred when measuring the angle and length was established. Based on this experimental data, the automatic measurement when measuring the projector causes less measurement error, so automatic measurement is recommended when measuring a small product. Also, an optimal measuring method is suggested for securing reliability on formulations of measurement automation.

• Journal of the Korean Wood Science and Technology
• /
• v.30 no.3
• /
• pp.85-90
• /
• 2002

This study was carried out to investigate the dimensional stability of bentwoods by three treatments: steaming, urethane varnish coating, and polyethylene glycol (PEG) treatment. Bentwood processing employed a bending-jig with only 4 cm radius of curvature (ROC). The used species were bitter wood (Picrasma quassioides), painted maple (Acer mono), and birch (Betula schmidtiii). The bending properties of these are well-known in bentwood production (Jung et al., 2002). The bentwoods were treated repeated at room temperature [20℃, RH 80% (12 hours) and 40℃ under RH 10% (12 hours)]. To estimate the dimensional stability of bentwoods, we measured the radius of curvature and end-distance. The best results could be attained with PEG treatment. Steaming was the worst treatment. Comparing the properties of the different species, the dimensional stability of bitter wood was excellent. It was concluded that the steaming treatment was unsuitable for dimensional stability of bentwoods.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.8
• /
• pp.31-39
• /
• 1996

In this paper, the error and its sources in manufacturing of bourdon tube pressure gage was studied, and the method to reduce such errors was discussed. In more detail, the effects of parallelism of rollers, spring back, uniformity of radius curvature and the ratio of circumferential speeds of rollers were invesrti- gated. As a reselt, we could find out that the aprallelism of roller affected to the displacement error at the free end of gage and that the amount of spring back was closely related with the ratio of circumferential speeds of rollers. The uniformity of curvature radius was determined by the distance between bending rollers and it was comparatively uniform in the range above 30 .deg. C from the both sides of tube. Also, the ratio of circumfer-ential speeds of rollers was finded out as a very important factor giving severe influence on the creep or the hysteresis of bourdon tube.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.34 no.3
• /
• pp.385-392
• /
• 2010

The breast types of middle-aged women of 80A (formerly 80B) size were classified through a 3D scanned nude body. Thirty seven measurements including the radius of curvature, surface area, volume, surface length, and breast displacements were used as input variables. We extracted five main factors through the factor analysis of the measurements and classified 36 subjects into 3 clusters through the cluster analysis. As a result of the factor analysis, the size of the breast, breast sag, the curvature of the inner and the outer breast curve, the width of the breast, and the nipple direction were found as the main factors. For the results of the classification of breast types, Cluster 1 was characterized by narrow breast width and unsymmetrical under the breast curve, whereas Cluster 2 was a wide and sagged shape. Cluster 3 was classified into big breast volume and symmetrical under-breast curve. The results are useful to the product development of high quality brassieres which reflect the 3D characteristics of breast types of middle-aged women.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.7 no.6
• /
• pp.1040-1046
• /
• 2006

This paper is aimed to investigate the deformation caused by ununiform contraction of injection molding with highly big differences of thickness by the continuity of various curvature radius. By CAE analysis, the uniform cooling structure and optimum molding conditions are found for Jars made of SAN and PMMA materials and applied to the design of chill. In order toevaluate the molding pressure, resin temperature, molding temperature, cooling conditions, Moldflow program is applied. As results of experiments, the deformation and inferiority phenomena in Jars are analyzed for each factor and proposed the injection molding conditions to minimize the cooling structure and reduce the cycle time.

• Journal of the Korean Wood Science and Technology
• /
• v.37 no.2
• /
• pp.128-136
• /
• 2009

Curved glued laminated timber (glulam) is rapidly coming into the domestic modern timber frame buildings and predominant in building construction. The radial stress is frequently occurred in curved beams and is a critical design parameter in curved glulam. Three models, Wilson equation, Exact solution and Approximation equation were introduced to determine the radial stress of curved glulam under pure bending condition. It is obvious that radial stress distribution between small radius and large radius was different due to slight change of neutral plane location to center line. If the beam design with extremely small radius, it should be considered to determine the exact location of maximum radial stress. The current standard KSF 3021 was reviewed and would be considered some adjustment determining the optimum radius in curved glulam. Current design principle is that the stress factor is given by the curvature term only in constant depth of the beam, but like tapered or small radius of beams, the stress factor by Wilson equation was underestimated. So current design formula should be considered to improvement for characterizing the radial stress factor under pure bending condition.

• Transactions of Materials Processing
• /
• v.16 no.7
• /
• pp.516-520
• /
• 2007

As the springback of sheet metal during unloading nay cause deviation from a desired shape, accurate prediction of springback is essential for the design of sheet stamping operations. On the removal of the applied load the specimen loses its elastic strain by contracting around the contour of the block, the radius $\rho$ can be determined by the residual differential strain. Therefore in this study the springback estimated by the residual differential strain is experimentally validated through the comparison with those obtained by U-bending test. The springback characteristics of two analytical models are also estimated at various processing conditions such as thickness, curvature of radius and drawing strain. The model based on residual differential strain has an applied transition strain where the springback undergoes a dramatic decrease. Both models show that springback decreases with increased strip thickness and with decreased radius of curvature. For no applied tension, the model based on residual differential strain predicts more springback as compared to the moment based model.